SIM28 GPS Module Modem with GPS antenna
- Operating voltage: 12V DC.
- Frequency l1, 1575.42mhz
- C/a code 1.023mhz chip rate
- 16-channels GPS search engine
- Ultra-low-power design (38mA, typical)
- Compact size
- Built-in low noise, high gain active antenna
- Super-cohesive magnetic for installation
- High sensitivity (up to -152dBm type)
- Super-cohesive magnetic for installation
- Apply to host devices with USB or RS232
- Compatible with TTL serial
8 Channel Tracking Sensor Module Board Trace Module Infrared Detection
5 Channel Tracking Sensor Module Board Trace Module Infrared Detection
- 5 channel high sensitivity sensor
- Operating Voltage: 0V - 5.5V
- Detection distance: 0 - 4cm (black and white line sensors), 0 - 5cm (adjustable distance detection)
- High accuracy for tracking black lines.
- Special touch sensor design, making the robot design simple
- Integrated infrared sensor barrier unblinded and distance can be adjusted by sliding rheostat
- Digital output signal
- Indicator LEDs
A1 Universal Carbon Resistors & Rotary Potentiometers Parts Set for Arduino
Sim800C GPRS/GSM Shield with Antenna
- Chip: QuadBand SIM800C GSM CHIP.
- Supply voltage range: 4 to 4.4V
- Quad-band 850/900/1800/1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- Compliant to GSM phase 2/2+
- Control via AT commands
- Configurable baud rate.
- SMA connector with GSM L Type Antenna.
- Built-in SIM Cardholder on Top Side.
- Arduino compatibility: Arduino UNO R3, Arduino Mega etc.
- Antenna type: Finger antenna.
- Output: TTL and RS232 serial output.
- Simcard holder: standard size.
- Buzzer for CALL and SMS indication
- Built-in Network, Status leds.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Normal operation temperature: -20 °C to +55 °C.
- On-Board Buzzer for Ring Indication.
- On-Board provision for Speaker and Mic.
- Low power consumption
- Dimensions: 17.6*15.7*2.3mm
- Weight: 1.3g
Wemos D1 Mini ESP8266 NodeMCU WIFI board for Arduino
- Microcontroller: ESP-8266EX
- Operating Voltage: 3.3 V
- Digital I/O Pins: 11
- Analog Input Pins 1(Max input: 3.2V)
- Clock Speed: 80MHz/160MHz
- Flash: 4M bytes
- Length: 34.2mm
- Width: 25.6mm
- Use BRT (Bias Resistor Transistor)
- Easier into flash mode.
- 30% increase in radiating area
- Good stability.
- 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Compatible with Arduino
- Compatible with Node MCU
- Support OTA wireless uploading
- 11 x I/O pins,1 x ADC pin
MMA845 Digital Triaxial Accelerometer Precision Tilt 3-Axis Module
- Power Supply: 3v-5V.
- Pitch: 15mm.
- Mounting hole diameter: 3mm.
- IIC digital output.
- Up to two interruption functions.
- ±2 g/±4 g/±8 g dynamically selectable full scale
- Three motion detection channels.
- Freefall down or motion detection.
- Automatic ODR change for auto-wake and return to sleep
- Pulse detection.
- Vibration detection.
- Dimension: 1.45cm x 2.05 cm (L x W).
PCF8574 I/O For I2C Port Interface
- Communication: I2C
- Operating Voltage: 2.5-V to 6V.
- Open-Drain Interrupt Output
- Compatible With Most Microcontrollers
- 8-bit remote I/O pins
- Up to 64 I/O ports
- Low standby current
- Operating temperature: 40 degrees C to +85 degree C
- Supports Arduino cascading, and you can use at most 8 modules to extend 64 I/O at the same time.
- Â the address can be changed by a set a toggle switch.
- Every 2 seconds, make P0-P7 port output High level, Low level, and put 3 toggle switches to ON, the address of module is 0x27.
- PCB Size: 36 x 16mm
1.44 red serial LCD display module 128*128 TFT Color Screen PCB Adapter
- Display Size: 1.44″
- Driver IC: ST7735
- Input Voltage: 3.3V to 5V
- Resolution:128×128 color pixels
- Touch Screen: NO
- Interface Type: SPI
- TFT color screen, the effect is far better than other small CSTN screen
- Fully compatible and alternative 5110 interface
- On-board LDO, support 5V/3.3V input voltage
- PCB Size: 44×30mm
BMP280 Pressure Sensor module High Precision Arduino
- Chip:BMP280
- Operating Voltage: 1.71V to 3.6V
- Communication method: Standard IIC/SPI communication protocol
- Pin pitch: 2.54mm
- Operating Temperature: -40 to +85 deg. Celsius
- Operating Pressure: 300 hPa to 1100 hPa
- Peak current: 1.12mA
- Current consumption: 2.7µA @ 1 Hz sampling rate
- Accuracy between( 700 to 900hPa and 25 to 40 deg. C): ±0.12hPa and ±1.0m
- Package 8-pin LGA metal-lid
- Relative accuracy(950 … 1050hPa @25°C): ±0.12 hPa, equiv. to ±1 m
- RoHS compliant, halogen-fre
- Module size: 11.5mm*15mm
Solid Relay Module 4 channel 5v low level trigger for Arduino
- Operating Voltage: 5V
- Operating Current: 12.5mA
- Maximum Load: 2A @ 240VAC
- Static Current: 0mA
- Channels: 4 Channel.
- Switch Max frequency: 5KHz.
- Trigger Voltage Range:
- Separate LEDs showing the status of each Solid-State Relay
- Strong anti-interference ability and stable performance
- Dimension: :57 x 55 x 25mm
Solid Relay Module 2 channel 5v low level trigger for Arduino
- 5V Solid State 2-channel Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 2.5v
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- -Low Signal (Solid-State Relay ON / CLOSE), 0V- 2V or GND
- -High Signal (Solid-State Relay OFF / OPEN), 3.3V - 5.0V or leave it floating
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm