Solid Relay Module 1 channel 5v low level trigger for Arduino
- 5V Solid State Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 3.3-5V.
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm
A6 GSM GPRS Module Quad Band SMS Voice
- Working voltage: 3.3V-4.2V
- Power voltage> 3.4V
- Standby average current: 3mA
- Working temperature: -30 to + 80
- Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900
- Connect onto any global GSM network with any 2G SIM
- Make and receive voice calls using an external 8Ω speaker & electret microphone
- Facility to connect 4-pole TRRS mic and headset
- 8V UART port level – compatible with Arduino, Raspberry-Pi
- Supports serial-based AT Command Set
- Accepts Micro SIM Card
- Send and receive voice calls and SMS messages
- Class 10 GPRS with 85.6Kbps download speed and 42.8Kbps upload speed
- Dimensions: 22.8 × 16.8 × 2.5mm
Xbee Module S2C XBP24CZ7UIT-004
- Protocol: ZigBee
- Modulation: DSSS
- Frequency: 2.4GHz
- Data Rate: 1Mbps
- Power: Output 18dBm
- Sensitivity: 101dBm
- Serial Interfaces: SPI, UART
- Antenna Type: Antenna Not Included, U.FL
- Transceiver chipset: Silicon Labs EM357 SoC
- Operating voltage: 2.7V-3.6V
- Current Receiving: 31mA ~ 45mA
- Current Transmitting: 120mA
- Mounting Type Through Hole
- Operating Temperature: -40°C ~ 85°C
Xbee Pro S2C Module XBP24CZ7WIT-004
- Operating voltage: 2.7V-3.6V
- Max data rate: 250kbps
- 63mW output (+17dBm)
- Range: 1 mile (1600m)
- ADC Channels: 6 10-bit ADC input pins
- Digital I/O: 8
- 128-bit encryption
- Transmit Current: 120mA at 3.3VDC
- Receive current: 31mA at 3.3VDC
- Data Rate: RF 250Kbps, serial up to 1Mbps
- Indoor/urban range up to 300ft (90m)
- outdoor/RF line of sight range up to 2miles (3200m)
- Transmit power is 63mW (+18dBm)
- Receiver sensitivity is -101dBm
- Local or over-air configuration
- AT or API command set
- External Antenna Required
- Firmware upgrades via UART, SPI or over the air (OTA)
- ISM 2.4GHz frequency band, DSSS (direct sequence spread spectrum) interference immunity
- Dimension: 2.438cm x 3.294cm
XBee Base Board USB Output
- Compatible with all ZigBee modules (Series 1 and Series 2.5, standard and Pro)
- Built-in 3V3 Voltage regulator
- 3V and 5V dual power output
- 3V and 5V IO compatible
- Status LEDs ( RX, TX, RSSI, Power)
- Zig Bee Pins available at 2.54 mm berg strip
- USB Powered.
- Small footprint.
- All XBee pins are broken out.
- Reset button.
- USB 2.0 protocol
- BitBang mode ready
- Easily connected to a PC via mini USB cable
- XBee-setting support software X-CTU
HLK-RM04 UART to Serial Wifi Ethernet Wifi Module
- 2.4GHz 802.11b/g/compatible
- Support IEEE 802.3、IEEE 802.3u
- Wi-Fi Client/AP/Router Mode
- Support WPS/wds
- Baud rate range: 1200~500000bps
- Support transparent transmission mode
- Support multiple security authentication mechanisms: WEP64/WEP128/ TKIP/ AES & WEP/WPA-PSK/WPA2-PSK
- Support multiple network protocol: PPPOE/TCP/UDP/DDDNS & /DHCP/DNS/HTTP/Firewre
- Support AT+ instruction set
- Support two configuration methods: Serial/WEB
- Serial speed ratio adjustable up to 320400
- Transparent dual-way data transmission
- Integrated 10/100M Ethernet port, Max. baud ratio up to 230.4kbps
- Adopts Ralink program, high-quality material
- Built-in 360M MIPS CUP, 16M RAM, 4M FLASH, wireless baseband, RF front-end, and multi-peripheral bus
- Support IEEE 802.11 b/g/n, transparent protocol data transmission mode
- TCP server/TCP Client/UDP work mode, support network protocol: TCP / UDP / ARP / ICMP / HTTP / DNS / DHCP
- Support DHCP auto gain IP, support IP distribution at AP Mode
- Built-in antenna or external antenna
- Dimensions: 29mm*40mm* 8.8mm
Bluetooth Module HM-10 BLE 4.0 CC2540
- BT Version: Bluetooth Specification V4.0 BLE
- Working frequency: 2.4GHz ISM band
- Operating voltage of Module: 2.0V – 3.6V
- Modulation method: GFSK (Gaussian Frequency Shift Keying)
- Send and receive no bytes limit.
- Working frequency: 2.4GHz ISM band
- UART Serial Interface
- Full-Speed USB Interface
- 12 General Purpose Input/output Pins
- In-System-Programmable Flash- 128 KB or 256KB
- 8-KB SRAM
- 32-kHz Sleep Timer With Capture
- Long-range: Open space has 100 Meters
- RF Power: -23dbm, -6dbm, 0dbm, 6dbm
- Speed: Asynchronous: 2-6K Bytes, Synchronous: 2-6K Bytes
- Power: +2.5V~3.5VDC 50mA
- Power: Active state 8.5mA; Sleep state 50~200uA
- Working temperature: –20 ~ +105 Centigrade
- Dimension: 27mm x 13mm x 2.2 mm
HC-05 Bluetooth Module
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Operating Voltage: 4V to 6V (Typically +5V)
- Operating Current: 30mA
- Modulation: GFSK(Gaussian Frequency Shift Keying)
- Emission power: ≤4dBm, Class 2
- Sensitivity: ≤-84dBm at 0.1% BER
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
- Working temperature: -20 ~ +75Centigrade
- Serial Bluetooth module for Arduino and other microcontrollers
- Range: <100m
- Works with Serial communication (USART) and TTL compatible
- Follows IEEE 802.15.1 standardized protocol
- Uses Frequency-Hopping Spread Spectrum (FHSS)
- Can operate in Master, Slave or Master/Slave mode
- Can be easily interfaced with Laptop or Mobile phones with Bluetooth
- Supported baud rate: 9600,19200,38400,57600,115200,230400,460800.
- Dimension: 26.9mm x 13mm x 2.2 mm
TB6560 4 Axis Stepper Motor Driver
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- Stepper motor drive current: 1.5A - 3A/phase
- With the large heat sink to ensure good heat dissipation
- Double-pole constant flow PWM actuation output
- 6N137 high-speed OptoCoupler, to ensure a high speed without stepping out.
- Compatible Stepper motors: 2/4 Phase, 4/6/8 leads stepper motors within 3.5A
- 1 - 1/16 micro step setting - higher accuracy, smoother operation
- Full closed-type optical isolation to protect the user's computer and equipment
- Professional design, two-stage signal processing, super anti-jamming
- Bipolar constant current chopper drive motor low-speed non-creeping phenomenon, noise, non-resonant region
- Four input control
-
Ultrasonic Module Waterproof
- Operating Voltage: 5 V
- Sonar Sensing Range: 25-450 cm
- Sensing Range: 450 cm
- Frequency: 40 kHz
- Resolution: about 0.5cm
- Quiescent current: 5mA
- Total current draw: 30mA
- Beam Angle: less than 50 degrees
- Working temperature: -10 ~ 70 Celsuis
- Storage temperature: -20 ~ 80 Celsuis
- Small size, easy to use
- Low voltage, low power consumption
- High accuracy
- Strong anti-jamming
- Integrated with wire enclosed waterproof probe
- Suitable for wet, harsh measurement
TTP229 16WAY
- On-board TTP229 capacitive touch sensor IC
- Operating voltage 2.4V~5.5V.
- Built-in regulator with external enable / disable option.
- Operating current, @VDD=3V no load.
- At low power mode typical 2.5uA.
- At fast mode typical 9.0uA; @VDD=3V.
- The response time is about 100mS at fast mode, 200mS at low power mode
- Built-in regulator
- Adjustable sensitivity
- Two modes
- Simple 8 key mode with independent 8 Channel parallel output.
- Advanced 16 Key modes with I2C interface output.
- Provides Fast mode and Low Power mode selection by pad option (LPMB pin).
- Provides direct mode or toggle mode CMOS output or open-drain output.
- Auto calibration for life and the re-calibration period is about 4.0sec when the key has not to been touched.
- PCB Size: 49.3 x 64.5 mm
TTP224 4WAY
- On-board TTP224 capacitive touch sensor IC 4 keys
- 4 board-level status indicator
- Working voltage: 2.4V-5.5V
- Advanced Pins breakout, so that the output mode and working mode are selectable.
- Low power selection
- Operating Current: < 9 µA
- Fast Mode and Low Power Mode
- Various Output Mode selection
- Outputs sensing via dedicated output pins
- PCB board size: 35 (mm) x 29 (mm)