Leap Motion Controller
- Power supply: 5V DC via USB connector (minimum 0.5A)
- Data connection: USB 2.0
- Interaction zone: Depth of up to 60cm (24”) preferred, up to 80cm (31”) maximum;
- 140×120° typical field of view.
- 3 LEDs spaced on either side and between the cameras, baffled to prevent overlaps.
- Construction: Aluminium and scratch-resistant glass
- Operating temperature: 32º to 113º F (0º to 45ºC)
- Storage temperature: 14º to 122º F (-10º to 50º C)
- Relative Humidity: 5% to 85% (non-condensing)
- Two 640x240-pixel near-infrared cameras; spaced 40 millimetres apart infrared-transparent window, operate in the 850 nanometre +/-25 spectral range; typically operates at 120Hz; capable of image capture within 1/2000th of a second.
- Highly accurate hand and finger tracking with near-zero latency
- 135° field of view extending above the device
- Orion SDK compatible with Windows 7 or newer
- Updated V4 tracking
Infrared Ir Obstacle Avoidance Detector Sensor Module Adjustable 2-180cm
- Power requirements: 5 VDC
- Communication: Digital High/Low Output
- A variety of welding methods, vertical and horizontal, to expand the scope of application
- Add precision potentiometer to adjust infrared 38KHz detection range
- Sensor detection with enabling the port, convenient signal line as bus application line
- Power-on enable port default level, the sensor enables the detection output signal
- Detection range up to 1.2 meters
- Software enhancement, setting can avoid infrared light interference of the same module or other kinds of infrared remote control devices
- Working condition of each module recorded with EEPROM, reduce the probability of mutual interference of the same paragraph to 1%
- Signal low output
- Pin SIP header, applied in breadboard or through-hole project
- On-board set jumper JP, the signal output has a latch function when shorted, otherwise, it is jog output
- Operating temperature: 32 to 158 ° F (0 to +70 ° C)
- Size: 2.4cm × 2.8cm
4-axis Flight Control Sensor HMC5883L BMP085 MWC GY-651
- Model: GY-651
- Use the chip: HMC5883L + BMP085
- Power supply:3-5v (internal low dropout regulator)
- Size: 13.5mm * 15.8mm (pin spacing standard 2.54mm)
- Communication modes: standard IIC communication protocol
- Magnetic field range: ± 1.3 to ± 8.1 gauss
- Pressure range: 300-1100hPa
- Chip 12bit AD converter, 16-bit data output Machine welding process to ensure quality
- Size: 18mmx14mm
TB6560 4 Axis Stepper Motor Driver
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- Stepper motor drive current: 1.5A - 3A/phase
- With the large heat sink to ensure good heat dissipation
- Double-pole constant flow PWM actuation output
- 6N137 high-speed OptoCoupler, to ensure a high speed without stepping out.
- Compatible Stepper motors: 2/4 Phase, 4/6/8 leads stepper motors within 3.5A
- 1 - 1/16 micro step setting - higher accuracy, smoother operation
- Full closed-type optical isolation to protect the user's computer and equipment
- Professional design, two-stage signal processing, super anti-jamming
- Bipolar constant current chopper drive motor low-speed non-creeping phenomenon, noise, non-resonant region
- Four input control
-
WS2812 LED BREAKOUT BOARD
- Input Voltage: -0.5～VDD+0.5V
- Supply voltage: 5v
- Operating voltage: 4v -7v
- Integrating control circuit and RGB chip
- Built-in signal reshaping circuit
- Built-in electric reset circuit and power lost reset circuit
- 256 brightness and 16777216 colour display
- Viewing angle: 120 degree
- Cascading port transmission signal
- Red Vf: 1.8~2.2V
- Green Vf: 3.0~3.2v
- Blue Vf: 3.2~3.4V
- Red Wavelength: 620~630 nm
- Green Wavelength: 515~530 nm
- Blue Wavelength: 465~475 nm
- Red luminous intensity(20mA): 550~700mcd
- Green luminous intensity(20mA): 1100~1400mcd
- Blue luminous intensity(20mA): 200~400mcd
- Dimension: 1.8*1.3*0.8mm