XBee Module S2C XB24CZ7WIT-004
- Protocol: ZigBee®
- Transceiver chipset: Silicon Labs EM357 SoC
- RF Standard: 802.15.4
- Frequency (ISM Band): 2.4GHz
- Digital I/O: 15
- ADC Channels: (4) 10-bit ADC inputs
- Data Rate: RF 250 Kbps, Serial up to 1 Mbps
- Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m)
- Transmit Power: 3.1 mW (+5 dBm)
- Channels: 16 channels
- Encryption: 128-bit AES
- Voltage requirements: 2.1 to 3.6 VDC
- Current requirements: ~33 mA @ 3.3VDC (transmit), ~28 mA @ 3.3VDC (receive), <1 uA @25ºC (sleep)
- Migratable to Digi Mesh and ZigBee PRO protocols
- Configuration Method: API or AT commands, local or over-the-air (OTA)
- Communication: CMOS UART / SPI
- Dimensions: 27.61 x 24.38 x 4.06 mm
- Operating temperature range: -40 to +85 °C
- Integrated, Wire Antenna
- Interoperable with other ZigBee-compliant devices
- Programmable versions with on-board microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Through-hole form factor enables flexible design
TURBIDITY SENSOR
- Working voltage: DC5V
- Measure water turbidity and estimate water quality
- Operating Current: 30mA (MAX)
- Response time : <500ms
- Digital and analogue output
- High level: 5V, low level: 0V
- Operating temperature: -30 to 80 degrees C
- Storage temperature:-10 to 80 degrees C
- Compatible with Arduino, Raspberry Pi, AVR, PIC, etc.
- Weight: 15g
ECG Sensor Module – AD8232
- Single-supply operation: 2.0 V to 3.5
- Designed to extract, amplify, and filter small biopotential signals.
- Leads-Off Detection.
- Shutdown Pin.
- LED Indicator.
- Analog Output.
- 5 mm Jack for Biomedical Pad Connection.
- Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart.
- Fully integrated single-lead ECG front end
- Common-mode rejection ratio: 80 dB (dc to 60 Hz)
- Two or three-electrode configurations
- Qualified for automotive application
- Fast restore feature improves filter settling
- Dimension: 3.5cm x 3cm
WEMOS D1 Pro mini-16m External Antenna Connector ESP8266 WIFI Networking Smart Component
VS1053 MP3 Recording Module Development Board with Onboard Recording For UNO
- SPI interface, the control signal lines are led out
- A headphone and stereo output
- Onboard Microphone for recording
- A line-in input interface
- Separate 3.5 mm Jack for MIC and Speaker
- Onboard Power Indicator
- 3V and 2.8V of LDO chip AMS-1117 on board provides up to 800mA current
- Can play a variety of music formats, support for OGG encoding real-time recording
- A single power supply: +5 VDC
- 288 Mhz crystal
- TF card slot
PN532 NFC MODULE
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI, and HSU (High-Speed UART)
- I2C / UART: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance: 5cm-7cm
- Easy to change mode: with a small SMD Toggle Switch
- Longer distance: the reading distance becomes 5~7cm,
- On-board level shifter, Standard 5V TTL for I2C and UART 3.3V TTL SPI
- Work as an RFID reader/writer
- Work as a 1443-A card or a virtual card
- Support NFC with Android phone
- Small size
- Dimensions: 42.7*40.4*4mm
5V Wireless Power Supply Module Wireless Charging Module Wireless Transmission Module
- Magnetic-Coupled Resonance Technology
- Transmitting Voltage: 5V
- Output Power: 36W
- Output Voltage & Current: 5V, 3A
- Coil Size: outer diameter 82mm; inner diameter 30mm
- Transmitting Module Size: 17mm*30mm
- Receiving Module Size: 30mm*54mm
- Insulation Coil
- Compact Design
- Stable power supply
- Insulation Coil
- Space-saving design
Xbee Module S2C XBP24CZ7UIT-004
- Protocol: ZigBee
- Modulation: DSSS
- Frequency: 2.4GHz
- Data Rate: 1Mbps
- Power: Output 18dBm
- Sensitivity: 101dBm
- Serial Interfaces: SPI, UART
- Antenna Type: Antenna Not Included, U.FL
- Transceiver chipset: Silicon Labs EM357 SoC
- Operating voltage: 2.7V-3.6V
- Current Receiving: 31mA ~ 45mA
- Current Transmitting: 120mA
- Mounting Type Through Hole
- Operating Temperature: -40°C ~ 85°C
SIM 800
- Quad-band 850/900/1800/1900MHz.
- GPRS class 2/10.
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
- High-Quality Product (Not hobby grade).
- 5V interface for direct communication with MCU kit.
- Configurable baud rate.
- Built-in SIM Cardholder.
- Built-in Network Status LED.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Low power.
Microwave Sensor
1.3″ OLED Display I2C 128*64 display module Blue 4pin
1.8″ TFT DISPLAY FOR ARDUINO
- Display Size: 1.8″
- Driver IC: ST7735
- Input Voltage (V): 3.3 to 5
- Pixel Resolution: 128 x 160
- Interface Type: SPI
- 18-bit (262,144) colour
- 4 or 5 wire SPI digital interface
- Built-in microSD slot – uses 2 more digital lines5V compatible!
- Use with 3.3V or 5V logic
- On-board 3.3V @ 150mA LDO regulator
- 2 white LED backlight, a transistor connected so you can PWM dim the backlight
- 1×10 header for easy breadboarding
- 4 x 0.9″/2mm mounting holes in corners
- Overall dimensions: 34 x 56 x 6.5mm
- Current draw is based on LED backlight usage: with full backlight draw is ~50mA