KY-036 Metal Touch Sensor Module
- Main chip: LM393
- Working voltage: for DC 5V
- Single-channel signal output
- Low-level output signal used for human body touch sensor alarm
- Adjustable sensitivity
- Pin Connector to board: 4 Pins
- Dimensions: 43 x 16 x 15 mm / 1.69 x 0.63 x 0.59 inch
- Single-channel signal output
- Low-level output signal used for human body touch sensor alarm
- Adjustable sensitivity
- Long life
- High reliability
RIKO SN04-N NPN Inductive Proximity Sensor
• Operating Voltage(V): 10 ~30
• Current Consumption Max: 5 mA
• Detection distance(mm): 5 mm.
• Type of detection: Inductive.
• Cable Length: 145 cm.
• Response Frequency: 500Hz Max.
• Protection class: IP 67
• Red LED checks the state of the proximity sensor
• High repeated positioning accuracy
• High switching frequency
• Wide voltage range
• Antivibration, dust, water and oil prevention
• Reverse power protection, short circuit protection, directly connecting with PLC
• It can replace small switches and limit switches
1/4 CMOS 640*480 USB Camera with Collapsible cable for Raspberry Pi
• Interface: USB 2.0
• Sensor: 1/4 Cmos
• Operating Current: <120 mA
• Picture Format: VGA
• Resolution: 640X480
• Supports 300k pixels, a maximum resolution of 640×480, and VGA/ YUY2 packed formats
• Dimension: 40mm × 15mm × 30mm; designed for Raspberry Pi and PC
• With a retractable USB cable, convenient to store
• Applies USB 2.0 High-speed Sensor, plug-and-play, no driver installation
• High definition and true colour images.
• max pixels: 12m pixels
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
AMS1117 5V POWER SUPPLY MODULE
• Input: DC 6.5V – 12V (input voltage must be more than the output voltage (more than 1V))
• Output: 5V, 800mA (load current cannot exceed 800mA)
• Onboard AMS1117 chip.
• Onboard power indicator to indicate power is turned on: Red LED.
• Output voltage interface, connection to facilitate the experimental.
• Specially designed two pin mounting holes, can be directly fixed on the whole expansion board for experiments.
• Small Compact Size, 4Pin Type, Breadboard Friendly.
• 2P single row pin input and output for easy connection
• Dual-panel design, the layout is nice
AMS1117 3.3V POWER SUPPLY MODULE
• Input: DC 4.5V – 12V (input voltage must be more than the output voltage (more than 1V))
• Output: 3.3V, 800mA (load current cannot exceed 800mA)
• Onboard AMS1117 chip.
• Onboard power indicator to indicate power is turned on: Red LED.
• Output voltage interface, connection to facilitate the experimental.
• Specially designed two pin mounting holes, can be directly fixed on the whole expansion board for experiments.
• Small Compact Size, 4Pin Type, Breadboard Friendly.
• 2P single row pin input and output for easy connection
• Dual-panel design, the layout is nice
Micro USB Breadboard 5V Power Supply Module
MPR121
- Connection Interface: I2C.
- Operating Voltage: 2.5-3.6 VDC
- Application: Capacitive Touch Sensor Controller
- Number of touches inputs:12
- Capacitive touch sensor controller is driven by an I2C interface.
- Can control up to twelve individual electrodes, as well as a simulated thirteenth electrode.
- Eight LED driving pins.
- Connection to the microcontroller /microprocessor via I2C bus.
FT232 to TTL
- Material: PCB + Electronic Component
- Support 3.3V, 5V
- Main Color: Red
- Chipset: FT232RL
- USB power has over current protection, using 500MA self-restore fuse
- RXD/TXD transceiver communication indicator
- Pin definition: DTR,RXD,TX,VCC,CTS,GND
- Pitch:2.54mm
- Module Size: About 36mm(length)*17.5mm(width)
- Interface : Mini USB
- Single-chip USB to asynchronous serial data transfer interface.
- Entire USB protocol handled on the chip. No USB specific firmware programming is required.
- Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
- Fully integrated USB termination resistors.
- Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
- Data transfer rates from 300 baud to 3 M baud (RS422, RS485, and RS232) at TTL levels.
- 128 byte receive buffer and 256 bytes transmit buffer utilising buffer smoothing technology to allow for high data throughput.
Logic Level Converter
3.5″ inch ILI9486 TFT Touch Arduino Shield LCD Module
- 5″ diagonal LCD TFT display, with bright 4 white-LED backlights, default state: on
- It can control the backlight to connect the transistor to a digital pin
- 480×320 Pixels, with colourful and 18-bit, 262,000 different kinds of shade
- 4-wire resistive touchscreen
- 8-bit digital interface, plus 4 control lines
