1.44 red serial LCD display module 128*128 TFT Color Screen PCB Adapter
- Display Size: 1.44″
- Driver IC: ST7735
- Input Voltage: 3.3V to 5V
- Resolution:128×128 color pixels
- Touch Screen: NO
- Interface Type: SPI
- TFT color screen, the effect is far better than other small CSTN screen
- Fully compatible and alternative 5110 interface
- On-board LDO, support 5V/3.3V input voltage
- PCB Size: 44×30mm
BMP280 Pressure Sensor module High Precision Arduino
- Chip:BMP280
- Operating Voltage: 1.71V to 3.6V
- Communication method: Standard IIC/SPI communication protocol
- Pin pitch: 2.54mm
- Operating Temperature: -40 to +85 deg. Celsius
- Operating Pressure: 300 hPa to 1100 hPa
- Peak current: 1.12mA
- Current consumption: 2.7µA @ 1 Hz sampling rate
- Accuracy between( 700 to 900hPa and 25 to 40 deg. C): ±0.12hPa and ±1.0m
- Package 8-pin LGA metal-lid
- Relative accuracy(950 … 1050hPa @25°C): ±0.12 hPa, equiv. to ±1 m
- RoHS compliant, halogen-fre
- Module size: 11.5mm*15mm
CH375B U-DISK Read Write Module USB interface communication SPI interface
Solid Relay Module 4 channel 5v low level trigger for Arduino
- Operating Voltage: 5V
- Operating Current: 12.5mA
- Maximum Load: 2A @ 240VAC
- Static Current: 0mA
- Channels: 4 Channel.
- Switch Max frequency: 5KHz.
- Trigger Voltage Range:
- Separate LEDs showing the status of each Solid-State Relay
- Strong anti-interference ability and stable performance
- Dimension: :57 x 55 x 25mm
Solid Relay Module 2 channel 5v low level trigger for Arduino
- 5V Solid State 2-channel Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 2.5v
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- -Low Signal (Solid-State Relay ON / CLOSE), 0V- 2V or GND
- -High Signal (Solid-State Relay OFF / OPEN), 3.3V - 5.0V or leave it floating
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm
Solid Relay Module 1 channel 5v low level trigger for Arduino
- 5V Solid State Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 3.3-5V.
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm
50Kg Pressure Micro Scale Weighing Sensor
- Capacity : 50.kg
- Output Sensitivity (mv/v): 1.0±0.1.
- Nonlinearity (%FS): 0.03.
- Repeatability (%FS): 0.03.
- Input Resistance: 1000. Ω
- Insulation Resistance : ≥5000.MΩ
- Alloy Steel wired weighing load cell
- High Accuracy
- Simple Structure & Easy Installation.
- Internal 1000 Ω half-bridge strain gauge load cell, the range is 50kg, half-bridge structure
- You can use multiple load sensors simultaneously to increase the capacity range, Parallel use to add additional capacity.
A6 GSM GPRS Module Quad Band SMS Voice
- Working voltage: 3.3V-4.2V
- Power voltage> 3.4V
- Standby average current: 3mA
- Working temperature: -30 to + 80
- Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900
- Connect onto any global GSM network with any 2G SIM
- Make and receive voice calls using an external 8Ω speaker & electret microphone
- Facility to connect 4-pole TRRS mic and headset
- 8V UART port level – compatible with Arduino, Raspberry-Pi
- Supports serial-based AT Command Set
- Accepts Micro SIM Card
- Send and receive voice calls and SMS messages
- Class 10 GPRS with 85.6Kbps download speed and 42.8Kbps upload speed
- Dimensions: 22.8 × 16.8 × 2.5mm
Xbee Module S2C XBP24CZ7UIT-004
- Protocol: ZigBee
- Modulation: DSSS
- Frequency: 2.4GHz
- Data Rate: 1Mbps
- Power: Output 18dBm
- Sensitivity: 101dBm
- Serial Interfaces: SPI, UART
- Antenna Type: Antenna Not Included, U.FL
- Transceiver chipset: Silicon Labs EM357 SoC
- Operating voltage: 2.7V-3.6V
- Current Receiving: 31mA ~ 45mA
- Current Transmitting: 120mA
- Mounting Type Through Hole
- Operating Temperature: -40°C ~ 85°C
Xbee Pro S2C Module XBP24CZ7WIT-004
- Operating voltage: 2.7V-3.6V
- Max data rate: 250kbps
- 63mW output (+17dBm)
- Range: 1 mile (1600m)
- ADC Channels: 6 10-bit ADC input pins
- Digital I/O: 8
- 128-bit encryption
- Transmit Current: 120mA at 3.3VDC
- Receive current: 31mA at 3.3VDC
- Data Rate: RF 250Kbps, serial up to 1Mbps
- Indoor/urban range up to 300ft (90m)
- outdoor/RF line of sight range up to 2miles (3200m)
- Transmit power is 63mW (+18dBm)
- Receiver sensitivity is -101dBm
- Local or over-air configuration
- AT or API command set
- External Antenna Required
- Firmware upgrades via UART, SPI or over the air (OTA)
- ISM 2.4GHz frequency band, DSSS (direct sequence spread spectrum) interference immunity
- Dimension: 2.438cm x 3.294cm
XBee Base Board USB Output
- Compatible with all ZigBee modules (Series 1 and Series 2.5, standard and Pro)
- Built-in 3V3 Voltage regulator
- 3V and 5V dual power output
- 3V and 5V IO compatible
- Status LEDs ( RX, TX, RSSI, Power)
- Zig Bee Pins available at 2.54 mm berg strip
- USB Powered.
- Small footprint.
- All XBee pins are broken out.
- Reset button.
- USB 2.0 protocol
- BitBang mode ready
- Easily connected to a PC via mini USB cable
- XBee-setting support software X-CTU
HLK-RM04 UART to Serial Wifi Ethernet Wifi Module
- 2.4GHz 802.11b/g/compatible
- Support IEEE 802.3、IEEE 802.3u
- Wi-Fi Client/AP/Router Mode
- Support WPS/wds
- Baud rate range: 1200~500000bps
- Support transparent transmission mode
- Support multiple security authentication mechanisms: WEP64/WEP128/ TKIP/ AES & WEP/WPA-PSK/WPA2-PSK
- Support multiple network protocol: PPPOE/TCP/UDP/DDDNS & /DHCP/DNS/HTTP/Firewre
- Support AT+ instruction set
- Support two configuration methods: Serial/WEB
- Serial speed ratio adjustable up to 320400
- Transparent dual-way data transmission
- Integrated 10/100M Ethernet port, Max. baud ratio up to 230.4kbps
- Adopts Ralink program, high-quality material
- Built-in 360M MIPS CUP, 16M RAM, 4M FLASH, wireless baseband, RF front-end, and multi-peripheral bus
- Support IEEE 802.11 b/g/n, transparent protocol data transmission mode
- TCP server/TCP Client/UDP work mode, support network protocol: TCP / UDP / ARP / ICMP / HTTP / DNS / DHCP
- Support DHCP auto gain IP, support IP distribution at AP Mode
- Built-in antenna or external antenna
- Dimensions: 29mm*40mm* 8.8mm