MEPUNO ROBOT CONTROLLER BOARD
- Microcontroller ATMEGA328 P.
- Crystal for the microcontroller: 16 MHZ
- USB type B connector
- 5volt, 12 volts regulated circuit.
- Two separate regulated 5volt power supplies.
- On-Board On/Off switch.
- OnBoard DC jack for powering up using adaptors.
- On-Board Reset Switch.
- Onboard L293D dual DC motor driver.
- Onboard TSOP IR receiver.
- On Board 3 user LEDs (with jumper selection), TX/RX indication LEDs.
- On-board connectors for analogue interfacing.
- On Board Buzzer Interface.
- On-Board PWM Interfacing.
- On board FTDI Driver for adruino.
- Berg headers for external interfacing.
- Supports I2C /3 WIRE /RF/USART serial communication standards.
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
SIM28 GPS Module Modem with GPS antenna
- Operating voltage: 12V DC.
- Frequency l1, 1575.42mhz
- C/a code 1.023mhz chip rate
- 16-channels GPS search engine
- Ultra-low-power design (38mA, typical)
- Compact size
- Built-in low noise, high gain active antenna
- Super-cohesive magnetic for installation
- High sensitivity (up to -152dBm type)
- Super-cohesive magnetic for installation
- Apply to host devices with USB or RS232
- Compatible with TTL serial
XBee Module S2C XB24CZ7WIT-004
- Protocol: ZigBee®
- Transceiver chipset: Silicon Labs EM357 SoC
- RF Standard: 802.15.4
- Frequency (ISM Band): 2.4GHz
- Digital I/O: 15
- ADC Channels: (4) 10-bit ADC inputs
- Data Rate: RF 250 Kbps, Serial up to 1 Mbps
- Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m)
- Transmit Power: 3.1 mW (+5 dBm)
- Channels: 16 channels
- Encryption: 128-bit AES
- Voltage requirements: 2.1 to 3.6 VDC
- Current requirements: ~33 mA @ 3.3VDC (transmit), ~28 mA @ 3.3VDC (receive), <1 uA @25ºC (sleep)
- Migratable to Digi Mesh and ZigBee PRO protocols
- Configuration Method: API or AT commands, local or over-the-air (OTA)
- Communication: CMOS UART / SPI
- Dimensions: 27.61 x 24.38 x 4.06 mm
- Operating temperature range: -40 to +85 °C
- Integrated, Wire Antenna
- Interoperable with other ZigBee-compliant devices
- Programmable versions with on-board microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Through-hole form factor enables flexible design
DN40 – 1.5” Water Flow Sensor
- Model: YF-DN40
- Material: Plastic
- Function: Sensor, flow rate control
- Working Voltage: DC 5V~24V
- Thread size: BSP 1 1/2”
- Size:L 92x OD46 5"
- Colour: Black color
- Flow rate: 5~200L/min
- Flow Pulse: F(Hz)=(0.45xQ) +/-3% Q=L/min
- 1L water= 27Pulse
- Working Current: 15mA (DC5 V)
- Working Voltage: DC 4.5V
- Load Capacity: =10 mA (DC 5 V)
- Operating Working Temperature: -25 to +80 Degree C
- Liquid Temperature: 85
- Accuracy: 3~5%
- Working environment: water, liquid, light oil etc.
- Hydrostatic pressure> 1.75MPa meet
- Insulation resistance> 100M> 100M
- Accuracy in 1 ~ 120L / MIN ± 2% in line
- Flow pulse characteristics F = (0.45 * Q) Q = L / Min meet
- Weight: 146g
TURBIDITY SENSOR
- Working voltage: DC5V
- Measure water turbidity and estimate water quality
- Operating Current: 30mA (MAX)
- Response time : <500ms
- Digital and analogue output
- High level: 5V, low level: 0V
- Operating temperature: -30 to 80 degrees C
- Storage temperature:-10 to 80 degrees C
- Compatible with Arduino, Raspberry Pi, AVR, PIC, etc.
- Weight: 15g
ECG Sensor Module – AD8232
- Single-supply operation: 2.0 V to 3.5
- Designed to extract, amplify, and filter small biopotential signals.
- Leads-Off Detection.
- Shutdown Pin.
- LED Indicator.
- Analog Output.
- 5 mm Jack for Biomedical Pad Connection.
- Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart.
- Fully integrated single-lead ECG front end
- Common-mode rejection ratio: 80 dB (dc to 60 Hz)
- Two or three-electrode configurations
- Qualified for automotive application
- Fast restore feature improves filter settling
- Dimension: 3.5cm x 3cm
WEMOS D1 Pro mini-16m External Antenna Connector ESP8266 WIFI Networking Smart Component
VS1053 MP3 Recording Module Development Board with Onboard Recording For UNO
- SPI interface, the control signal lines are led out
- A headphone and stereo output
- Onboard Microphone for recording
- A line-in input interface
- Separate 3.5 mm Jack for MIC and Speaker
- Onboard Power Indicator
- 3V and 2.8V of LDO chip AMS-1117 on board provides up to 800mA current
- Can play a variety of music formats, support for OGG encoding real-time recording
- A single power supply: +5 VDC
- 288 Mhz crystal
- TF card slot
USB Host Shield
- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Operates over the extended -40°C to +85°C temperature range
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
- Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).
3.5” TFT for Raspberry Pi
- Operating Voltage: DC 5V.
- Touch Screen Controller: XPT2046
- Resistive touch.
- Dimension: 3.5 inch
- Resolution: 320×480 pixel
- Colors:65536
- Backlight: LED
- LCD Type: TFT
- LCD Interface: SPI
- Compatible with any version of the raspberry pie
- Drivers provided (works with your own Raspbian/Ubuntu/Kali)
- Compatible with Raspberry Pi A, B, A+, B+, 2B, 3B, 3B+,4B versions
- Size perfectly fits the Pi
- High-quality immersion gold surface plating
- Supports Raspbian system, Ubuntu system, kali Linux system
- Support software keyboard (system interaction without keyboard/mouse)
- Dimension: 10 x 8 x 4 cm
- Weight: 150 Grams
