5” TFT for Raspberry PI
- Display Size: 5″
- Resolution: 800 x 480 pixel
- Supply Voltage: 5V @1A
- Touch: 4-wire resistive touch
- LCD DRIVER IC: ILI9486L
- Refresh rate：60HZ
- Good touch response
- Large viewing angle
- Fast response time
- Support backlight control for low power consumption
- Compatible with Raspberry Pi 3, Pi2, Model B/B+
- Not only for Raspberry Pi
- Not only for mini-PCs, it can also work as a computer monitor
- The monitor can work with standard HDMI devices (adjust output resolution to 800*480),
- Touch function is only available for Raspbian and Ubuntu systems.
- Touch panel function not supported---Retropie, Windows 10
- LCD Size：11mm*77.93mm
- Weight:175g
Waveshare 5inch HDMI LCD (B) 800×480
- 800x480 high hardware resolution
- Resistive touch control
- Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers
- When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free
- When working as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free
- The backlight can be turned off to lower power consumption
- 5mm audio jack speaker provided and supports HDMI audio output
- Supports popular game consoles like Microsoft XBOX360 Sony PS4 and Nintendo Switch etc.
- Multi languages OSD menu for power management brightness/contrast adjustment etc.
- Also supports VGA input(specific cable is required and should be purchased separately)
- Dimensions:18 x 10 x 9 cm
- Weight: 200 Grams
Speech Recognition Module
- Working voltage: 3.3/5V
- Local Voice Recognition
- Very low rate of false triggering
- Speaker connector(JST2.0, the speaker is not included)
- Built-in microphone
- 22 recognition entry
- Default Baud rate: 9600
- Flash: 2Mbytes
- Microphone Sensitivity: -40dB
- Microphone SNR: 58dB
- Operating temperature: 0 – 85 degrees C
PICKIT-3 Programmer
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.
Black 2M Usb 6 Led Waterproof Borescope Endoscope Inspection Tube Camera
EP2C5T144 Altera Cyclone II FPGA Mini Development Board
- Onboard the EP2C5T144 chip.
- EPROM chip configuration using EPCS4, the size of 4Mbit.
- Onboard 50M active patch crystal (Crystal Slaughter halfback).
- Power supply with a largemouth outlet, single 5V power supply.
- Board has a power indicator and resets the switch.
- Onboard 3 SMD LED, the LED test can be done an experiment, more experiments using lead to complete.
- More IO ports and clock pins through the pin leads through these interfaces can be extended to any memory and peripherals.
- Board using a high-quality tantalum capacitor power filter.
- Support NiosII embedded CPU development.
- Board Dimension (LxWxH) mm: 72 x 52 x 13mm.
- Weight: 26gm.
Fingerprint Scanner TTL GT511C3 – 3.3V to 6V
- Model: GT-511C3
- Operating Voltage(VDC): 3 to 6
- CPU: ARM Cortex M3 Core (Holtek HT 32F2755)
- Sensors: Optical
- Image Size: 202 x 258 Pixel
- Resolution: 450 DPi
- Effective Scanning Area(mm): 20 x 16
- False Acceptance Rate (FAR): 0.001%
- False Rejection Rate(FRR): < 0.1%
- Operating Temperature : -20°C ~ +60°C
- Default Baud Rate: 9600bps
- High-Speed, High-Accuracy Fingerprint Identification using the Smack Finger 3.0 Algorithm
- Read and Write Fingerprint Templates and Databases
- Simple UART protocol (Default 9600 baud)
- Capable of 1:1 Verification and 1:N Identification
- High-accuracy & high-speed fingerprint identification technology.
- Works well with dry, moist, or rough fingerprints.
- 200 fingerprints storage.
- Easy one-touch enrolment.
- Dimensions(mm): 37 x 17 x 9.5
- Weight: 6gm
Finger print Scanner Module – TTL (GT-521F32)
- Operating Voltage: 3.3V to 6V DC
- Simple UART & USB communication protocol.
- Complies with USB 2.0 full-speed specification.
- Ultra-thin optical sensor.
- Finger window: 12.9 x 16.9 mm.
- Image Size: 258 x 202 Pixels.
- Resolution 450 dpi.
- Capable of 360° recognition.
- Storage for 200 unique fingerprints.
- False Acceptance Rate (FAR): <0.001%
- False Rejection Rate (FRR): <0.01%
- Wake up on Finger Function.
- CPU: ARM Cortex M3 Core MCU).
- Ultra-thin Optical Sensor.
- Works well with dry, moist or rough fingerprints
- Anti-scratch with surface high hardness ≧5
- 1:1 verification, 1:N identification.
- High accuracy and high-speed fingerprint identification technology.
- External UART-to-USB converter required (TX & RX levels: 3.3V).
EMG Sensor / Muscle Sensor Module For Arduino
- Power Supply: Normally ±9V dual power supply, the minimum voltage is ±3.5V
- The diameter of the Electrode Pad: 52 mm
- Cable Length: 2 feet
- Improved adjustable gain (more rugged)
- 5mm connector
- On-board port for new cables Connects to the board straight out of the box
- Supported with Arduino, Breadboard mountable
- Weight: 30gm.
GY-906 MLX90614ESF Contactless Temperature Sensor Module
- Small size, low cost
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Easy to integrate
- Factory calibrated in wide temperature range:
- Sensor temperature: -40...+125°C
- Object temperature: -70...+380°C
- High accuracy of 0.5°C over the wide temperature range
- (0...+50°C for both Ta and To) High (medical) accuracy calibration
- The measurement resolution of 0.02°C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuousreading
- Simple adaptation for 8...16V applications
- Sleep mode for reduced power consumption
STM32 Nucleo-64 development board with STM32F103RB MCU, supports Arduino and ST morpho connectivity
- STM32 microcontroller with LQFP64 package
- Two types of extension resources
- mbed-enabled (mbed.org)
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
- Flexible board power supply
- Three LEDs
- Two push buttons: USER and RESET
- USB re-enumeration capability: three different interfaces supported on USB
- Comprehensive free software HAL library including a variety of software examples
- Supported by wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs
NUCLEO-64 STM32G071RBT6 Development Board Arduino & ST Morpho Connectivity
- STM32 microcontroller in LQFP64 package
- 1 user LED shared with ARDUINO®
- 1 user and 1 reset push-buttons
- 768 kHz crystal oscillator
- Board connectors: ARDUINO Uno V3 expansion connectors morpho extension pin headers for full access to all STM32 I/Os
- Flexible power-supply options: ST-LINK, USB VBUS, or external sources
- On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
- Comprehensive free software libraries and examples available with the STM32Cube MCU Package
- Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded Workbench®, MDK-ARM, and STM32CubeIDE
- Board-specific features
- External SMPS to generate Vcore logic supply
- 24 MHz HSE
- Board connectors: External SMPS experimentation dedicated connector Micro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
- Arm® Mbed Enabled™ compliant