Heatsink for Raspberry pi 4
- Reduces the risk of hardware failure due to overheating
- Low profile, will fit into most cases.
- Simple, Passive cooling. No need for noisy fans.
- Perfectly sized for the RPi’s CPU
- Self-adhesive thermal layer for easy application
- The thermal resistance of 27°C/W
- Dimensions(LxWxH) mm:
- Material: Aluminium
- Colour: Silver
- Weight: 3g for a set of 3 Heat Sink
Logic Level Converter
IR-08H Infrared Obstacle Avoidance Sensor Module
- Infra-Red IR Emission Receiver IR-08H for Arduino
- Onboard with HS0038B HS38B IR receiver
- Operating Voltage: 3V – 5.5V
- Detection range : 2cm – 40cm
- Output level: Low logic level when an obstacle is detected
- Working current: 20mAh
- Working temperature: -10’C~+50’C
- IO interface: 4 line (-/+/S/EN)
- Output signal: TTL Level
- Adjusting mode: Multi resistance regulation
- Effective angle: 35°
- Size: 4.5 * 1.1cm(approx)
- Easy to assemble and use
- On-board detection indication
- Pin Connection to the board: 4 pins
- A pre-set knob to fine-tune distance range
MQ-9 Carbon Monoxide, Methane and LPG Gas Sensor Module
- Input voltage: DC 5V
- Power: 150mA
- DO output: TTL digital 0 and 1 (0.1 and 5V)
- AO output: 0.1-0.3V (relatively clean), the highest concentration voltage is about 4V.
- Suitable for home or factory gas leakage monitoring devices.
- Have better sensitivity to Carbon Monoxide, Methane and LPG Gas.
- High quality dual-panel design, with power indicator and TTL signal output instructions.
- DO switching signal (TTL) output and AO analog signal output.
- TTL output valid signal is low. (When the output low signal is on, it can be directly connected micro-controller or relay module.)
- Analog output voltage: the higher concentration, the higher voltage.
- Four screw holes, easy positioning.
- Long life and stability, quick response and resume.
Electrobot Micro HDMI to HDMI Cable (Compatible with Raspberry Pi 4)
3S BMS BOARD 25A
- Charging Voltage: 12.6V DC CC/CV
- Balance Voltage for Single Cell: 4.2V
- Max Continuous Charge/Discharge Current: 25A
- Overcharge voltage range: 4.25-4.35v + 0.05v.
- Over discharge voltage range: 2.3-2.7v + 0.05v.
- Operating current: 0 – 25A.
- Operating temperature: -40 – +50℃.
- Instantaneous current: 35 – 40A.
- Storage condition: -40 – +80℃.
- Quiescent current: less than 30uA.
- Balance current: about 40 – 50mA.
- Effective life: more than 30000 hours.
- Internal resistance: less than 100m ohms.
- Short-circuit protection: protection, delayed self-recovery.
4×4 Keypad Board Matrix Keyboard 16 Key Buttons For Arduino
- 4×4 Matrix Keyboard Module with 16 buttons
- Small in size and hence Save space
- More convenient to use
- Expanded development application modules for single chip
- With 16 keys and an 8 pin
- The maximum voltage across each button: 24v
- The maximum current across each button: 3mA
- Easy communication with any microcontroller
- Ultra-thin design
- Adhesive backing provides easy integration
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
TM1637 4 Bits Digital Tube LED Display Module With Clock Display for Arduino
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 30 mA
- Display Dimensions: 42x24x12 (LxWxH) mm
- Ease to use.
- Ease of multiplexing.
- Can use as a 4 digit display unit.
- Can use as a clock display.
- The counter project uses 7 segment display.
- 4 M2 screws positioning holes for easy installation
Msp-Exp430G2 Msp430 Launchpad
• 14-/20-pin DIP (N) Socket
• 20 pin Launchpad standard leveraging the Booster Pack ecosystem
• On-Board EZ-FET emulator featuring Energy Trace™ technology
• USB debugging and programming interface featuring a driverless installation and application UART
• serial communication with up to 9600 Baud
• Supports MSP430G2xx2, MSP430G2xx3, and MSP430F20xx devices in PDIP14 or PDIP20 packages
• Two general-purpose digital I/O pins connected to green and red LEDs for visual feedback
• Two push button for user feedback and device reset
• Easily accessible device pins for debugging purposes or as socket for adding customized extension boards
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.
TL866CS USB Universal Programmer EEPROM FLASH 9 Adapters Extractor for 13000 Ics
- Model: TL866CS
- With a Multi-functional ICSP interface
- 40pin ZIF socket, fully automatic, support fast mode SPI
- USB interface for both data transfer and power supply
- With over-voltage and over current protection
- Supports the serial number of the chips two times development, built-in a variety of commonly used automatic numbering functions
- English Language Support
- It can program faster than another programmer 500%~1000%
- Programming EPROM, EEPROM, FLASH, SPI, I2C,93Cxx, ICSP etc.
- Supports thousands of most popular application devices (13071+)r
- Ideally suits the portable/convenient applications, which includes: car automotive field ECU chip tuning, airbag reset, mileage, satellite devices, BIOS refreshing, Xbox, Wii gaming machines EPROM sync, PIC / MCU development, newer laptop technology and newer desktop PC etc.
- Dimensions: 4.02 in x 2.48 in x 1.22 in (10.2 cm x 6.3 cm x 3.1 cm)
- Weight: 138 g
Arduino Duemilanove Development Board with USB Cable
- Microcontroller: ATmega168/ATmega 328
- Operating Voltage: 5V
- Input Voltage: 7-12V
- Input Voltage: 6-20V
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by the bootloader
- SRAM: 1 KB (ATmega168) or 2 KB (ATmega328)
- EEPROM: 512 bytes (ATmega168) or 1 KB (ATmega328)
- Clock Speed: 16 MHz