Battery & Accessories
2 Cell Battery holder AA Black with Wire
Solar Charge Controller 12v/24v 10A
Lipo Battery Charger B3
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
3S BMS BOARD 25A
- Charging Voltage: 12.6V DC CC/CV
- Balance Voltage for Single Cell: 4.2V
- Max Continuous Charge/Discharge Current: 25A
- Overcharge voltage range: 4.25-4.35v + 0.05v.
- Over discharge voltage range: 2.3-2.7v + 0.05v.
- Operating current: 0 – 25A.
- Operating temperature: -40 – +50℃.
- Instantaneous current: 35 – 40A.
- Storage condition: -40 – +80℃.
- Quiescent current: less than 30uA.
- Balance current: about 40 – 50mA.
- Effective life: more than 30000 hours.
- Internal resistance: less than 100m ohms.
- Short-circuit protection: protection, delayed self-recovery.
7.4 Lipo Battery Indicator Display Board
- High reliability, low cost and compact size.
- LED Flash for low charge warning.
- Memory option to recall the quantity of electricity.
- Specifically designed to monitor the power level of the battery while charging or discharging.
- Provides instant battery status to permit effective management of the charging.
- Display of 4 segments LED bar graph
- Easy to install and operate.
LIPO Voltage Battery Tester
- Input: 1S-8S Battery
- Battery Type: Lipo/LiFe/Li-ion/LiMn
- Voltage Detection Precision: +/- 0.01V
- Unit Voltage Display Range: 0.5V to 4.5V
- Total Voltage Display Range: 0.5V to 36V
- 1S Test Mode Voltage Range: 3.7V to 30V
- Low voltage alarm mode for 2-8S
- Alarm Set Value Range: OFF~2.7V to 3.8V
- Buzzer Alarm for low voltage indication.
- Useful for measuring each cell voltage.
- It has a mode button at the top for setting the desired voltage value.
- Dimension: 4*2.5*1cm
TP4056 Li-ion 5V/1A 18650 BATTERY CHARGER
- Input interface: Micro USB
- Input voltage: 4.5V-5.5V
- Full charge voltage: 4.2V
- Current: 1A adjustable
- Charge precision: 1.5%
- Battery over-current protection: 3 A
- The battery Under-voltage protection: 2.5 V
- Linear charging mode
- Maximum charging current output: 1000 mA
- Use mature charging chip TD4056 for simple peripheral circuits
- Good performance & high charging accuracy
- Dimension: 25*19*10m
- Weight: 16gm
Solar Charge Controller 12v/24v 40A
- High efficiency:Â your batteries are charged quickly.
- Capacity for solar panel configurations of up to 3600 Wp.
- Suitable for AGM, gel, wet and Mastervolt Lithium Ion batteries.
- Fast and flexible setting of battery type.
- Battery temperature sensor for long lifespan.
- Automatic 12 V/24 V/48 V detection.
- Switchable output.
- Noiseless operation.
- LCD display.
- Fully protected against overtemperature, overload, high/low battery voltage, high/low PV voltage, short circuit and reverse polarity.
12V / 2A Battery Charger
- This is a durable product with a 6-month warranty.
- The adapter is easy to use.
- It comes with a long wire.
- Wide input voltage range (100VAC-280VAC).
- Very low no-load power consumption.
- Very low ripple & noise output for device safety.
- Protections against- under-over voltage/ overload/ short circuit with auto-restart on fault removal.
- Thermal shut down (140°C) with auto-restart on cold condition.
- Soft start & low inrush current.
- Isolation up to 3kv for 5sec.time period.
- High operating ambient temperature up to 60°C.
- Highly efficient, compact, durable and long life.
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,