470uf 250V DC Electrolytic Capacitor
4700uf 35V Samwha DC Electrolytic Capacitor
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
ACS712 20A Hall Current Sensor Module SMD SOP8 SOIC8
- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- 80 kHz bandwidth
- Total output error 1.5% at TA= 25°C
- Small footprint, low-profile SOIC8 package
- 2 mΩ internal conductor resistance
- 1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- 0 V, single supply operation
- 66 to 185 mV/A output sensitivity
- Output voltage proportional to AC or DC currents
- Factory-trimmed for accuracy
- Extremely stable output offset voltage
- Nearly zero magnetic hysteresis
- Ratiometric output from supply voltage
Motor Driver IC – L293D
- Can be used to run Two DC motors with the same IC.
- Speed and Direction control is possible
- Motor voltage Vcc2 (Vs): 4.5V to 36V
- Maximum Peak motor current: 1.2A
- Maximum Continuous Motor Current: 600mA
- Supply Voltage to Vcc1(vss): 4.5V to 7V
- Transition time: 300ns (at 5Vand 24V)
- Automatic Thermal shutdown is available
- Available in 16-pin DIP, TSSOP, SOIC packages
- Featuring Unit rode L293 and L293D
- Wide Supply-Voltage Range: 4.5 V to 36 V
- Separate Input-Logic Supply
- Internal ESD Protection
- Thermal Shutdown
- High-Noise-Immunity Inputs
- Output Current 1 A Per Channel (600 mA for L293D)
- Peak Output Current 2 A Per Channel (1.2 A for L293D)
- Output Clamp Diodes for Inductive Transient Suppression
ADXL 335 Accelerometer IC
- 3-axis sensing
- Small, low profile package
- 4 mm × 4 mm × 1.45 mm LFCSP
- Low power : 350 μA (typical)
- Single-supply operation: 1.8 V to 3.6 V
- 10,000 g shock survival
- Excellent temperature stability
- BW adjustment with a single capacitor per axis
- RoHS/WEEE lead-free compliant
- 8V- 3.6V single-supply operation
- Integrated X, Y, and Z axis accelerometer on a single chip
- X and Y axis has a 0.5Hz to 1600Hz bandwidth
- Z axis has a 0.5Hz to 550Hz bandwidth
- Hermetically sealed for temp and humidity resistance
SIM Card Holder
TSOP 1738 IR Receiver
- Supply Voltage: 5 V
- Operating current: 5mA
- Power consumption: 0.4 to 1.0 mA
- Ee irradiation: 0.35 mW/m2 typ.
- Angle of detection: 90
- Dimensions of the casing (mm): 12.5 x 10 x Thickness 5.8
- Temperature range: -25 C to +85 C
- Can detect IR signals from Remotes (38kHz)
- High Range and wide coverage area.
- Will respond only to IR signals, due to high immunity against ambient light
- Low power consumption
- Has in-built pre amplifier
- TTL and CMOS compatible
TSOP1838 IR Reciever Metal Small
- Supply voltage: 2.7 to 5.5V
- Reception Distance: 18 Meters
- P.F Centre Frequency: 38KHz
- Supply Current: 0.4 to 1.5mA
- Reception angle :+/- 45 degrees
- VOH (6V Vcc): 4.5V
- VOL (5V Vcc): 0.4V
- Photo detector and preamplifier in one package
- Internal filter for PCM frequency
- TTL and CMOS compatibility
- Output active low
- Improved shielding against electrical field disturbance
- Suitable burst length: 6 cycles/burst
- Low power consumption.
- Immunity to ambient light is high
IR Receiver 3 Leg Black Metal
- Sensing distance: 45m
- Supply voltage: 2.5V- 5.5V
- Mounting type: through hole
- Operating temperature: -25°C ~ 85°C (TA)
- Directivity: 45°
- Supply Current: 350µA
- Power Dissipation: 10 mW
- Proper Shielding Against EMI
- Comes with metal legs
- High Immunity against Ambient Light
- Photo Detector and Preamplifier in single Package
- Low Supply Current
- Insensitive to Noise and Supply Voltage Ripple
74LS540 High-Speed CMOS Logic Octal Buffer and Line Driver IC
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm