Showing 145–156 of 173 results

Tauren Gear series 100 – 600 rpm

  • Maximum Speed(RPM): 600 (at 12V)
  • Rated Voltage: 12V
  • Nominal Voltage: 12V
  • Stall Torque(Kg-Cm): 14 kgcm
  • No Load Current: 700 mA
  • Rated Load Current: 4 A
  • Stall Current: 14 A
  • Weight (gm): 500 gram

Tauren Geared DC Motor Series 100 – 12V, 30 RPM

  • Maximum Speed(RPM): 30 (at 12V)
  • Rated Voltage: 12V
  • Nominal Voltage: 12V
  • Stall Torque(Kg-Cm): 90 kgcm
  • No Load Current: 700 mA
  • Rated Load Current: 4 A
  • Stall Current: 14 A
  • Weight (gm): 500 gram

Tauren Geared DC Motor Series 100 – 12V, 300 RPM

  • Maximum Speed(RPM): 300 (at 12V)
  • Rated Voltage: 12V
  • Nominal Voltage: 12V
  • Stall Torque(Kg-Cm): 14 kgcm
  • No Load Current: 700 mA
  • Rated Load Current: 4 A
  • Stall Current: 14 A
  • Weight (gm): 500 gram

TB6560 CNC 3 Axis Stepper Motor Driver Controller Board

970.00 inc. GST
 

TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor

970.00 inc. GST
  • Supply voltage up to +32 VDC
  • Output current up to 3.0A
  • Pulse frequency up to 20 KHz
  • Suitable for 2-phase and 4-phase motors
  • Over-voltage and short-circuit protection
  • 7 output current choices, max 3200 steps/rev
  • Automatic idle-current reduction
  • Single-chip motor driver for sinusoidal micro-step control of stepping motors
  • High output withstands voltage due to the use of BiCD process:
  • Forward and reverse rotation
  • Selectable phase excitation modes (2, 1-2, 2W1-2, and 4W1-2)
  • High output withstand voltage: VDSS = 40 V
  • High output current: IOUT = TB6560AHQ: 3.5 A (peak)
  • Internal pull-down resistors on inputs: 100 kΩ
  • Output monitor pin: MO current (IMO (max) = 1 mA)
  • Reset and enable pins

TB6600

1,100.00 inc. GST
  • Input Current: 0 to 5A
  • Output Current: 0.5 to 4.0A
  • Control Signal: 3.3 to 24V
  • Power (MAX): 160W
  • Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
  • Temperature: -10~45℃
  • H bridge bipolar constant current drive.
  • Support 8 kinds of current control
  • Support 7 kinds of micro steps adjustable
  • The interfaces adopt high-speed optocoupler isolation
  • Automatic semi-flow to reduce heat
  • Large area heat sink
  • Anti-high-frequency interference ability
  • Input anti-reverse protection
  • Overheat, over current, and short circuit protection
  • A total of standard single pulse interface.
  • Offline retention function.
  • The semi-enclosed casing can adapt to a more stringent environment.
  • Provide energy saving half-automatic current lock function.

TB6612FNG Dual Motor Driver Module 1A for Arduino/Other Microcontroller

200.00 inc. GST
  • Driver Model: TB6612FNG
  • Operating voltage: 2.7 V to 5.5 V
  • Limited Maximum Voltage: 15V max
  • Output current: 1.2A
  • Maximum Current: 3.2A (peak)
  • Number of Channels: 1
  • Standby control to save power
  • CW/CCW/short break/stop motor control modes
  • Built-in thermal shutdown circuit and a low voltage detecting circuit
  • All pins of the TB6612FNG broken out to 0.1 spaced pins
  • Filtering capacitors on both supply lines
  • Dimensions: 30 x 20 x 10mm
  • Weight: 22 gm

Tower Pro MG996R Servo Motor (180 Degree Rotation)

330.00 inc. GST
  • Operating voltage: 4.8 V - 7.2 V
  • Running Current: 500 mA – 900 mA (6V)
  • Stall Current: 2.5 A (6V)
  • Temperature range: 0 ºC – 55 ºC
  • Control System: Analog
  • Operating Angle: 180degree
  • Required Pulse: 900us-2100us
  • Direction: CCW
  • Operating speed: 0.17 s/60º (4.8 V), 0.14 s/60º (6 V)
  • Dead band width: 5 μs
  • Wire length: 30cm
  • Connector: 3 pin 'S' type female header
  • Weight: 55 g
  • Dimension: 40.7 x 19.7 x 42.9 mm approx.
  • Servo arms & screws included, and fit with Futaba servo arm
  • It’s universal “S” type connector that fits most receivers, including Futaba, JR, Hitec ,GWS, Cirrus, Blue Bird, Blue Arrow, Corona, Berg, Spektrum.
 

Towerpro MG90S Mini Digital 180 Degree Servo

359.00 inc. GST
  • Model: MG90S
  • Operating voltage: 4.8V~ 6.6V
  • Servo Plug: JR
  • Stall torque @4.8V : 1.8kg-cm
  • Stall torque @6.6V : 2.2kg-cm
  • Modulation: Analog
  • Dimensions: 23.1*12.2*29.0 mm
  • Gear Type: Metal
  • Rotation/Support: Dual Bearings
  • Rotational Range: 180°
  • Pulse Cycle: 20 ms
  • Pulse Width: 400-2400 µs
  • High resolution
  • Accurate positioning
  • Fast control response
  • Constant torque throughout the servo travel range
  • Excellent holding power
  • Weight: 13 gm

TowerPro MG995 Metal Gear Servo Motor (180° Rotation)

330.00 inc. GST
  • Operation Voltage : 4.8 - 7.2Volts
  • Gear Type: All Metal Gears
  • Operating Speed (4.8V no load): 20sec / 60 deg
  • Operating Speed (6.0V no load): 16sec / 60 deg ( no load)
  • Stall Torque (4.8V): 10kg/cm
  • Stall Torque (6.0V): 12kg/cm
  • Stable and shockproof double ball bearing design
  • Dead band width: 5 µs
  • Temperature range: 0 ºC – 55 ºC.
  • Control System: Analog
  • Operating Angle: 120degree
  • Required Pulse: 900us-2100us
  • Connection cable is thicker.
  • Equips high-quality motor.
  • High resolution
  • Accurate positioning
  • Fast control response
  • Constant torque throughout the servo travel range
  • Excellent holding power
  • Dimension : 40.7 × 19.7 × 42.9 mm
  • Weight : 55g

TowerPro MG996R 360 Deg Rotation Digital High Torque Servo Motor

350.00 inc. GST
  • Gear Type: Metal gear
  • Servo Plug: JR (Fits JR and Futaba)
  • Weight: 55g
  • Dimension: 40.7×19.7×42.9mm
  • Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v)
  • Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v)
  • Operating voltage: 4.8 ~ 6.6V
  • Gear Type: Metal gear
  • Dead band width: 1us
  • Wire length: 32cm
  • Servo arms & screws included, and fit with Futaba servo arm
  • It’s universal “S” type connector that fits most receivers, including Futaba, JR, Hitec ,GWS, Cirrus, Blue Bird, Blue Arrow, Corona, Berg, Spektrum.
  • CE & RoHS approved

TowerPro SG-5010(180° Rotation)

349.00 inc. GST
  • Model: SG5010
  • Operating voltage: 4.8V~ 6V
  • Servo Plug: JR
  • Stall torque @4.8V : 5.5kg-cm
  • Stall torque @6.6V : 6.5kg-cm
  • High resolution
  • Accurate positioning
  • Fast control response
  • Constant torque throughout the servo travel range
  • Excellent holding power
  • Weight: 39 gm