MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
59TYD-375-2B AC Synchronous Motor 220VAC 50HZ – 5 RPM
- RPM: 30.
- Torque: 68 kgcm.
- Voltage: 12-240 VAC.
- Input Power: <13W.
- Frequency: 50/60Hz.
- Rated Current: 100mA.
- Noise (dB): 42.
- Insulation Class: B.
- Direction of Rotation: CW OR CCW Controlled by Capacitor. "
- Main Application - beverage machine, blenders, grill, oven, office equipment, household appliances.
- Weight:580g.
RS-50-555 Gear Motor – High Torque 12v DC 300 rpm
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 2 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 10Kg-cm
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
RS-50 High Torque Side Shaft DC Geared Motor 60 RPM
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 13 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 40Kg-cm
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
Solar Charge Controller 12v/24v 40A
- High efficiency: your batteries are charged quickly.
- Capacity for solar panel configurations of up to 3600 Wp.
- Suitable for AGM, gel, wet and Mastervolt Lithium Ion batteries.
- Fast and flexible setting of battery type.
- Battery temperature sensor for long lifespan.
- Automatic 12 V/24 V/48 V detection.
- Switchable output.
- Noiseless operation.
- LCD display.
- Fully protected against overtemperature, overload, high/low battery voltage, high/low PV voltage, short circuit and reverse polarity.
MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
59TYD-375-2A AC Synchronous Motor 220VAC 50HZ – 1.6, 5, 12, 20, 40. RPM
Stepper Motor Nema 23 kg 7.2 kg Dual shaft
- Rated Voltage: 6.6 V
- Current/ phase: 1A
- Resistance/ phase: 6.6ohms
- Inductance/ phase: 8.2 mH
- Holding Torque: 7.2 kg-cm
- of Leads - 6
- Rotor Inertia - 275
- Weight: 0.65kg
- Detent Torque: 0.36 kg-cm
- Step Angle - 1.8°
- Step Angle Accuracy - ±5% (full step, no load)
- Resistance Accuracy - ±10%
- Inductance Accuracy - ±20%
- Frame Size (mm) - 57x57
- Shaft Length (mm) - 20.6
- Shaft Diameter (mm) - 6.35
- Comparably more powerful than NEMA17 motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Worm Gear Box Reduction Motor 12V 10rpm 10 kg-cm Torque – WGM370128500-828K
STEPPER MOTOR NEMA 23 7.2KG
JX PS-5521MG 20KG Large Torque Metal Gear Standrd Analog Servo
- Name: PS-5521MG Analog Servo
- Maximum Angle: 90°
- Gear: Metal
- Operating Voltage:4.8V-6V
- Dead band: 7µs 1520µs / 50hz
- Operating Speed (4.8V): 0.18 sec/60°
- Operating Speed (6V): 0.16 sec/60°
- Stall Torque (4.8V): 17.25 kg.cm (239.55oz/in)
- Stall Torque (6V): 20.32 kg-cm (281.89 oz/in)
- Connector Wire Length: JR 265 mm (10.43in)
- Bearing: 2BB
- Dimension: 40.5x40.3x20mm
- Weight: 85g