MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
IMAX B3 Charger
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
DYS Motor D2826 1800KV
- Item name: D2826 1800KV
- Voltage: 4V~14.8V
- Battery: 2~4s LiPoly
- Max watt:300W
- Max Current: 19A
- Suggested prop: 9045
- Pull: 800g
- Shaft: 3.17mm in Diameter
- Thrust: 1050g (9045 prop/4s)
- Efficiency: <4g/W
- Suggested Propeller: 7x4(3S) ~ 9x4.7 (2S)
- ESC: 40A
- Ri(M ): 0.078
- Pull: 780g
- Shaft: M5
- Motor Mount Holes: 16mm or 19mm
- Dimensions: 26.2 × 27.7mm
- Weight: 51g
A2212 BRUSHLESS DC MOTOR 2200KV
- Motor KV: 2200
- Operating voltage: 7.2V to 12V (2 to 3Li-poly or 6to10 NiCad)
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of three phase connection.
- Long life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 1000gms approx.
- Thrust @ 3S with 0945 propeller: 750gms approx.
- Thrust @ 3S with 0845 propeller: 650gms approx.
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
A2212 BRUSHLESS DC MOTOR 1400KV
- Operating voltage: 7.2V to 12V
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of three-phase connection.
- Long-life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 1000gms approx.
- Thrust @ 3S with 0945 propeller: 650gms approx.
- Thrust @ 3S with 0845 propeller: 550gms approx.
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
3.17mm RC Aluminum Bullet Propeller Adapter Holder
- Bore Diameter: 3.7mm (expandable up to 4.1mm).
- Material: Aluminium.
- Colour: Silver.
- Ease of interfacing.
- Rust-free and stain-free aluminum metal construction.
- Used to capture propeller with BLDC motor in quad-copter/multi-rotor/drone.
- High-quality aluminum material.
- Suitable for brushless motors and speed controllers.
- Delicate workmanship.
- High-Quality RC 3.17mm Prop Adaptor For Motor Propeller Plane, Multicopter, Quadcopter
- Dimension: 2.5mm Long x 12mm Diameter
- weight: 4g
Bullet Connector 3.5MM
- Diameter: 3.5mm
- Length:1.5CM & 1.5CM
- Amperage Rating: 60A -180Amps
- Hook up RC Battery to Electronic
- Hook up Brushless motor to electronic speed control
- These have low resistance and gives the best electric flow
- 5mm gold connectors Male
- 5mm gold connectors Female
- Dimension: 2.7*2.1*3inch
- Weight: 67gm
IMAX B6-AC Lipo NiMH Battery Charger/Discharger 1-6 Cells
- AC Input Voltage: 100V ~ 240v or 12V DC input
- Current: 2.5A Max.
- Max Charge: 50W
- Max Discharge: 5W
- Charge Current Range: 0.1A ~ 6.0A
- Discharge Current Range: 0.1~1.0A NiMH/NiCd Cells, 1~15A LiIon/LiPoly Cells 1~6A Pb
- Plug Type: Female End Type: IEC(To Charger)
- Plug Type. Male End Type: EU plug (To Power Distribution Board).
- The cables come with a fitted fuse.
- Microprocessor controlled
- Li-ion, LIPO, and LiFe are capable
- Input voltage monitoring. (Protects car batteries at the field)
- Battery break-in and cycling feature
- Data storage (Store up to 5 packs in memory)
- Internal resistance checker to see pack health
- Delta-peak sensitivity
- Individual cell balancing
- EU Plug to IEC C13 which is used in devices such as ac adapters, digital cameras, camcorders, monitors, printers, Direct TV and more!\
- Dimensions: 135 x 144 x 36mm
- Weight: 632g
IMAX B6 DIGITAL RC LIPO NiMH BATTERY BALANCE CHARGER
- Input Voltage: 11V to 18V
- Battery Voltage: 2V to 20V
- Power Max Charge: 50W – Max
- Discharge: 5W
- Charge Current Range: 0.1 to 5.0A
- Discharge Current Range: 0.1~1.0A NiMH/NiCd Cells, 1~15A LiIon/LiPoly Cells, 1~6A Pb
- Microprocessor controlled
- LiIon, LiPoly, and LiFe are capable
- NiCad and NiMH are capable
- Large range of charge currents
- Storage charge function
- Time limit function
- Delta-peak sensitivity
- Individual cell balancing
- Battery break in and cycling.
- Input voltage monitoring (Protects car batteries at the field)
- Data storage (Store up to 5 packs in its memory
- Dimensions: 133x87x33m
- Weight 277g
HK-300 (2.5W) submersible mini water pump AC 220V-240V
A3967 STEPPER MOTOR DRIVER
- A3967 precision micro-stepping driver
- Power supply: 7v to 30v
- Logic voltage: 5v to 3.3v
- Higher the voltage higher the torque at high speed
- Adjustable current control from 150Ma/ phase to 750ma phase
- Automatic current decay mode detection/selection
- Fast, slow, and mixed current decay modes
- Internal UVLO and thermal shutdown circuitry
- Crossover current protection
- Micro stepping resolution to full, half, quarter, and eighth steps by broken out MS1 and MS2 pins.
- Compatible with Arduino, GRBL G-Code interpreter for driving3-axis CNC machines
- Salington sink drivers used
- Compactible with 4, 6,8 wire stepper motor of any voltage
7 PIN 0.96” 128*64 WHITE OLED
- High resolution: 128*64
- Input voltage: 3V to 5 V DC
- Ultra-wide viewing angle >160 degree
- Ultra-low power consumption
- Fully compatible with Arduino, 51 series, MSP430, STM32/2, CSR IC.
- Driver IC: SSD1306
- Display colour: white
- Performs without the need for a backlight
- Interface: IIC/SPI, needs 4 I/O only
- Compatible I/O level: 3.3v, 5v
- Working temperature: -40 degrees to 70 degrees Celsius
- Dimension: 27.3*27.8*3.7mm
- Support a wide range of input
- Size: 99gm