Towerpro MG90S Mini Digital 180 Degree Servo
- Model: MG90S
- Operating voltage: 4.8V~ 6.6V
- Servo Plug: JR
- Stall torque @4.8V : 1.8kg-cm
- Stall torque @6.6V : 2.2kg-cm
- Modulation: Analog
- Dimensions: 23.1*12.2*29.0 mm
- Gear Type: Metal
- Rotation/Support: Dual Bearings
- Rotational Range: 180°
- Pulse Cycle: 20 ms
- Pulse Width: 400-2400 µs
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
- Weight: 13 gm
74LS922 16-Key Encoder IC
ATMEGA128A Atmel Microcontroller IC
- Flash (Kbytes): 128 Kbytes
- Pin Count: 64
- Operating Freq. (MHz): 16 MHz
- CPU: 8-bit AVR
- Max I/O Pins: 53
- Ext Interrupts: 8
- SPI: 1
- UART: 2
- ADC channels: 8
- SRAM (Kbytes): 4
- EEPROM (Bytes): 4096
- Operating Voltage (Vcc): 2.7 to 5.5V
- High-performance, Low-power Atmel AVR 8-bit Microcontroller
- Advanced RISC Architecture – 133 Powerful Instructions - Most Single-clock Cycle Execution – 32 × 8 General Purpose Working Registers + Peripheral Control Registers – Fully Static Operation – Up to 16MIPS Throughput at 16MHz – On-chip 2-cycle Multiplier
- High Endurance Non-volatile Memory segments – 128Kbytes of In-System Self-programmable Flash program memory – 4Kbytes EEPROM – 4Kbytes Internal SRAM – Write/Erase cycles: 10,000 Flash/100,000 EEPROM – Data retention: 20 years at 85°C/100 years at 25°C(1) – Optional Boot Code Section with Independent Lock Bits
- In-System Programming by On-chip Boot Program
- True Read-While-Write Operation – Up to 64 Kbytes Optional External Memory Space – Programming Lock for Software Security – SPI Interface for In-System Programming
- JTAG (IEEE std. 1149.1 Compliant) Interface – Boundary-scan Capabilities According to the JTAG Standard – Extensive On-chip Debug Support Atmel-8151J-8-bit AVR Microcontroller_Datasheet_Complete-09/2015 – Programming of Flash, EEPROM, Fuses and Lock Bits through the JTAG Interface
XT90 Male-Female connector pair with Housing
24V RO water solenoid valve
- Operating Voltage: 12V / 24V DC
- Current Requirement: 400 mA
- Connections: Push Fit Type
- Nozzle Diameter: 6.3 mm
- Normally Closed Valve
- Electrical connection: Fast-on tags
- Compact and convenient.
- Easily installed and serviced
- Precise and reliable.
- Pressure-regulating valve
- Suitable for fluids like water, oil, air.
GSM Antenna Dlenp 2dbi/3dbi Patch Antenna with SMA Male Connector
- GSM Antenna
- Gain: 2 to 3dbi
- Wire Length: 3 metre
- 3dbi Sticker Antenna
- GSM Antenna
- SMA Male Connector
- Frequency Range(MHz): 824-960/1710-1990Mhz
- Bandwidth (MHz): 136/280
- VSWR≤1.5
- Gain(dB): 2-3dbi
- Max Input power(W): 60W
- Input Impedance: 50 Ω
- Polarization Type: Vertical
- Cable Type: RG174
- Mounting Adhesive
- Net weight: 47g
Dual USB 5V 1A 2.1A Mobile Power Bank Battery Charger
- Micro USB input: 5V 1A
- Charging voltage input: 5V-6V 1A.
- Step-up voltage output: 5V 1A/2.1A (Dual output, Total 2.5A).
- USB Output: 5V 2.1A / 5V 1A(Dual USB interface)
- Charging display: intelligent digital display
- Batteries Type: liquid lithium-ion batteries (18650)
- Best for Arduino, DIY Kits, Power bank, etc.
- Protection circuit: Overcharge protection: 4.250V Overcharge protection release: 4.100V.
- Protection circuit: Over-discharge protection: 2.900V Over-discharge protection release: 3.000V.
- Idle time before LCD switch off 60secs.
- Screen size:27mm x 17mm
- Dimension: 57mm x 28mm
N20 Model – 300 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:50.
- Nominal Voltage: 6v
- Voltage Range: 3v to 12v
- RPM: 300
- No load Current: 40mA
- Stall Current: 550mA
- Stall Torque: 700 g-cm.
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting , not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
N20 Model – 40 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:380.
- Nominal Voltage: 6v.
- Voltage Range:Â 3v to 12v.
- RPM: 40.
- No-load Current: 40mA.
- Stall Current: 550mA.
- Stall Torque: 7500 g-cm.
- Ideal for making robots
- Lightweight, high torque, and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft
