LM7912C Negative Voltage Regulator
LNK304PN Off-line Switcher IC
- Drain Voltage: -0.3 V to 700 V
- Peak Drain Current: 400 mA
- Feedback Voltage: -0.3 V to 9 V
- Feedback Current: 100 mA
- Operating Junction Temperature: -40 °C to 150 °
- Lowest Component Count, Energy-Efficient Off-Line Switcher IC
- Lowest cost and component count buck converter solution
- Fully integrated auto-restart for short-circuit and open loop fault protection – saves external component costs
- 66 kHz operation with accurate current limit – allows low cost off-the-shelf 1 mH inductor for up to 120 mA output current
LNK500PN Switcher IC
LNK564PN Off-line Switcher IC
MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
MBR10100 Dual Diode 10A 100V
- Maximum repetitive peak reverse voltage VRRM: 100V
- Working peak reverse voltage VRWM: 100V
- Maximum DC blocking voltage VDC: 100V
- Voltage rate of change (rated VR) dV/dt = 10 000 V/µs
- Guard–Ring for Stress Protection
- Low Forward Voltage
- 150°C Operating Junction Temperature
- Guaranteed Reverse Avalanche
- Epoxy Meets UL94, VO at 1/8″
- Low Power Loss/High Efficiency
- High Surge Capacity
- Low Stored Charge Majority Carrier Conduction
MBR3045 Dual Diode
- Maximum recurrent peak reverse voltage VRRM: 45V
- Maximum RMS Voltage VRMS: 31.5V
- Maximum DC blocking voltage VDC: 45V
- Power pack
- Guarding for overvoltage protection
- Lower power losses, high efficiency
- Low forward voltage drop
- High forward surge capability
- High frequency operation
- Solder dip 275 °C max., 10 s, per JESD 22-B106
MC1489 Quad Line Receiver IC
MC1496PG Balanced Modulator Demodulator IC
MEGA16A Atmel Microcontroller IC
- Flash (Kbytes): 16 Kbytes
- Pin Count: 44
- Operating Freq. (MHz): 16 MHz
- CPU: 8-bit AVR
- Max I/O Pins: 32
- Ext Interrupts: 3
- SPI: 1
- UART: 1
- ADC channels: 8
- SRAM (Kbytes): 1
- EEPROM (Bytes): 512
- Operating Voltage (Vcc): 2.7 to 5.5
- High Performance, Low Power Atmel®AVR® 8-Bit Microcontroller Family
- Advanced RISC Architecture.
- High Endurance Non-volatile Memory Segments
- Peripheral Features includes Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode,One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode , Real Time Counter with Separate Oscillator , Six PWM Channels , 8-channel 10-bit ADC in TQFP.
- Programmable Serial USART ,Master/Slave SPI Serial Interface.
MEGA328P Atmel Microcontroller IC
- Flash (Kbytes): 32 Kbytes
- Pin Count: 32
- Operating Freq. (MHz): 20 MHz
- CPU: 8-bit AVR
- Max I/O Pins: 23
- Ext Interrupts: 24
- SPI: 2
- UART: 1
- ADC channels: 8
- SRAM (Kbytes): 2
- EEPROM (Bytes): 1024
- Operating Voltage (Vcc): 1.8 to 5.5
- Package: PDIP 28P3 28
- High Performance, Low Power Atmel®AVR® 8-Bit Microcontroller Family
- Advanced RISC Architecture
- High Endurance Non-volatile Memory Segments
- Peripheral Features includes Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode,One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode,Real Time Counter with Separate Oscillator,8-channel 10-bit ADC , Programmable Serial USART,Master/Slave SPI Serial Interface
- Operating Voltage: 1.8 - 5.5V