ANTENNA WIFI
Antenna Specifications:
- Color: Black
- Radiation: Omni-directional
- Gain:8dBi
- Frequency Range(MHz): 2400-2500, 5150-5850MHz
- Connector Type: RP-SMA Male (Hole)
- Angle Adjustable: 90° 135° 180°
- Dimension: 16cm/ 6.3”(Unbend) / 13.5cm/ 5.31”(Bend)
- Wight: 13.5g / 0.48 oz per antenna
- Color: Black & Gold
- Length: 15cm / 5.9''
- Wight:4.4g / 0.17 oz per pigtail cable
- Connector Type: U.FL/ IPEX to RP-SMA Female
PIC18F4550 Microcontroller IC
- Maximum CPU Frequency: 48 MHz
- Architecture: 8 bit
- Program Memory (Flash): 32 kB
- RAM: 2048 byte
- Internal Oscillator: 8MHz, 32KHz
- ADC: 1 (13 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- C Compiler Optimized Architecture with optional Extended Instruction Set
- 100,000 Erase/Write Cycle Enhanced Flash Program Memory typical
- 1,000,000 Erase/Write Cycle Data EEPROM Memory typical
- Flash/Data EEPROM Retention: > 40 years
- Self-Programmable under Software Control
- Priority Levels for Interrupts
- 8 x 8 Single-Cycle Hardware Multiplier
- Extended Watchdog Timer (WDT): - Programmable period from 41 ms to 131s
- Programmable Code Protection
- Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via two pins
- In-Circuit Debug (ICD) via two pins
- Optional dedicated ICD/ICSP port (44-pin devices only)
- Wide Operating Voltage Range (2.0V to 5.5V)
AD633 Analog Multiplier IC
- Analog Multiplier
- Four-Quadrant Multiplication
- Low Cost 8-Lead Package
- Complete—No External Components Required
- Laser-Trimmed Accuracy and Stability
- Total Error Within 2% of FS
- Differential High Impedance X and Y Inputs
- High Impedance Unity-Gain Summing Input
- Laser-Trimmed 10 V Scaling Reference
- Supply Voltage:18V
SSR Relay 3-32V / 25A S-Kap
ESC 30A BLDC Electronic Speed Controller
- Standard 30A BLDC ESC Electronic speed controller
- Input voltage: DC 6V-16.8V(2-4S Lixx)
- BEC: 5V 2amp
- Easy handling and good compatibility
- Suitable Batteries: 2-3S LiPo.
- Application: BLDC Motors, Multirotor, RC Planes et
- Running current: 30A (Output: Continuous 30A, Burst 40A up to 10 Secs.)
- Size: 36* 26* 7mm
- Weight: 32g
12V / 2A Battery Charger
- This is a durable product with a 6-month warranty.
- The adapter is easy to use.
- It comes with a long wire.
- Wide input voltage range (100VAC-280VAC).
- Very low no-load power consumption.
- Very low ripple & noise output for device safety.
- Protections against- under-over voltage/ overload/ short circuit with auto-restart on fault removal.
- Thermal shut down (140°C) with auto-restart on cold condition.
- Soft start & low inrush current.
- Isolation up to 3kv for 5sec.time period.
- High operating ambient temperature up to 60°C.
- Highly efficient, compact, durable and long life.
IMAX B3 Charger
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
Geared Offside Motor 200 rpm High Torque – Off Side Shaft 12v DC
- Voltage : 3v to 12v
- RPM :200 (at 12v)
- Nominal Voltage : 12v
- No- Load Current : 20mA
- Full Load Current :800mA
- Full (Stall) Load Torque: 6 kgcm
- The lightweight and compact-sized motor with high performance.
- The Shaft is D type hence wheel/ coupling arrangement is simple.
- Useful for hobbyists and for a DIY project.
- Weight: 150gm
Offside Gear Motor – Side Shaft 30 rpm 12v DC
- Voltage : 3v to 12v
- RPM :30 (at 12v)
- Nominal Voltage : 12v
- No- Load Current : 20mA
- Full Load Current :800mA
- Full (Stall) Load Torque:20 kgcm
- The lightweight and compact-sized motor with high performance.
- The Shaft is D type hence wheel/ coupling arrangement is simple.
- Useful for hobbyists and for a DIY project.
- Weight: 150gm