“2WD Mini Round Double-Deck Smart Robot Car Chassis DIY Kit No battery”
1 meter 7 x 7 mm Cable drag Chain Wire Carrier With End Fits
1045(10×4.5) SF Propellers Black
- Length: 10″.
- Pitch: 4.5″.
- Weight: 14 gm.
- Shaft Diameter: 6 mm.
- Total length: 10 inch / 254 mm.
- Color-Black
- No of Blades-2
- Plastic Reducers-2.75, 3, 3.17, 4, 4.70, 5, 6, 6.25
- Quick to release, quick to attach
- Comes with thin and wide blades
- 1045(10×4.5) SF Propellers Black features an epoxy resin cover
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- A set of 2 x 1045 Propellers. The set includes one clockwise rotating and one counter-clockwise rotating propeller with 2 x propeller shaft adapters.
- Dimensions-30 x 6 x 4 cm
- Weight(gm)-28
1245(12X4.5) Propeller
- Length: 12″
- Pitch: 4.5″
- Weight: 36.5g
- Shaft Diameter: 6mm
- Total Length: 30.5cm
- Material: ABS
- Durable plastic construction provides both lightness and rigidity.
- 1245(12X4.5) Carbon Fiber Black comes with an Epoxy resin cover.
- Very strong and lightweight.
- Includes a set of reducers 3, 4, 5, 6,
- Quick to release, quick to attach
- Provides greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 28gm
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
3PI miniQ Car wheel Tyre 42mm N20 DC Gear Motor Wheel
4 Wheel Metal Chassis Grey for Robotics
- Dimensions: 194x 104 x 48 (LxWxH).
- Weight: 270 gm.
- Material: Metal sheet.
- Colour: Grey.
- Sheet Thickness: 1.5 mm.
- Many perforated holes have given for easy attachment of development board and sensors.
- High durable, non-flexible
- Lightweight
- Can be re-shaped easily
- Resistant to corrosion
- Highly rigid
- Compatible with a single type of screw
- The chassis support one rotary castor wheel for balancing the robot & to rotate easily.
4-wheel Robot Smart Car Chassis Kits Car Model with Speed Encoder
- Operating Voltage: 3-6V VDC
- Gear Ratio: 1:48
- No-load speed(5V): about 200 RPM
- Rated Torque: 0.8 Kg.cm @ 5V
- Load current: 170mA (when it is 4.5V)
- Shaft Length: 10 mm
- Shaft Type: 6 mm, Double-D
- Loading Capacity: Max 2.5Kg
- Wheel Diameter: 65 mm
- Wheel Width: 27 mm
- Body Material: Plastic
- Grip Material: Rubber
- Very handy and simple in assembling/disassembling.
- Strong components so as to withstand extreme terrain conditions.
- Transparent Car Chassis.
- Attractive design.
- Double-layer structure, much of mounting holes, enough space
- Easy to install a variety of control panels, sensors
- Simple mechanical structure, easy for installation.
- Adopts 4 DC motors for better power, speed and load capacity
- Easy interface with Arduino development platform
- Enormous space between middle & bottom chasis
5045(5×4.5) SF Propellers 2CW+2CCW-2pair
- Length: 5″.
- Pitch: 4.5″.
- Weight: 22 gm.
- Shaft diameter: 5mm.
- Total length: 5 inch / 125 mm.
- Material: Glass Fiber Nylon
- Durable plastic construction provides both lightness and rigidity.
- 5045(5X4.5) Glass Fiber Nylon Bullnose Black Propellers comes with an Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
6 in 1 DIY Solar kit for Kids, Solar Powered Vehicles, Science Educational Toys for Kids STEAM Kits
- Product name: STEM Solar Power Science Educational Toy Set
- Product size (After assembly):
- Robot: 5 x 5 x 8 cm
- Helicopter: 25.5 x 8.5x8cm
- Submarine: 14 x 8 x10.5 cm
- Mildwill: 8.5x8.5x9cm
- Aircraft: 25.5x8.5 x17cm
- Car: 6.5 x 5 x5.5cm
- Package Dimensions: 19*6*24CM
- Suit for : 10,11,12,13,14 years old Boys, Girls, Kids, Children, toddler, nephew, niece, granddaughter, grandson, friends, Birthday, Christmas, party or other holiday gifts
6045(6×4.5) Propeller
- Length: 6″.
- Pitch: 4.5″.
- Shaft Diameter: 5mm.
- Total length: 6 inch / 150 mm.
- Material: Glass Fiber Nylon
- It includes a set of plastic reducers(3, 4, 5, 6 mm)
- Durable plastic construction provides both lightness and rigidity.
- 6045(6X4.5) Glass Fiber Nylon Propeller comes Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
8045(8×4.5) SF Propellers 2CW+2CCW-pair
- Length: 8″.
- Pitch: 4.5″.
- Weight: 14 gm.
- Shaft Diameter: 5 mm.
- Total Length: 8 inch / 220 mm.
- Material: Glass Fiber Nylon
- Comes with thin and wide blades
- 8045(80×4.5) SF Propellers Black features an epoxy resin cover.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
8045(8X4.5) Propeller
- Length: 8″
- Pitch: 4.5″
- Weight: 36.5g
- Shaft Diameter: 6mm
- Total Length: 177mm
- Material: ABS
- Durable plastic construction provides both lightness and rigidity.
- 1245(12X4.5) Carbon Fiber Black comes with an Epoxy resin cover.
- Very strong and lightweight.
- Includes set of plastic reducers (3, 3.17, 4, 4.70, 5, 6, 6.25 mm).
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 25gm
Advance Metal Chassis 1
- Dimensions: 115mm x 105mm x 45mm
- Weight: 200 gm
- Material: Metal sheet
- Color: Red.
- Sheet Thickness: 1.5 mm.
- Motor Fitting Hole Diameter: 13.75 mm.
- Many perforated holes have given for easy attachment of development board and sensors.
- Center Shaft gear motor and side shaft gear motor can be used for this chassis.
AfroFlight Naze32 Rev6 Flight Controller Board
- Version: 6 DOF
- Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line
- USB on right side
- 32-bit processor running at 3.3V/72MHz (STM32F103CB).
- Up to 8 Ch. RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spectrum satellite receivers
- Built-in FrSky telemetry inverter
- Battery voltage monitoring
- SBUS Inverter built-in
- Spectrum satellite
- Modern GUI for all operating systems, Baseflight Configurator.
- Supports multiple platforms: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
- MPU6500 : 3-Axis MEMS Gyroscope + accelerometer
- Onboard MicroUSB for setup and configuration
- BMP280 barometer
- Modern GUI for all operating systems, Baseflight Configurator.
- Sonar pads w/resistors added for direct connection to 5V sonar3.3V
- Dimensions: 36x36 mm (30.5mm Mounting)
- Weight: 5.3 grams (no headers, 7.3 grams with).
Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
- Colour: Black
- Material: Glass Fibre
- Upper Frame size:90x60x2mm
- Lower Frame Size: 100x70x2mm
- Shock absorber Height: 10×12mm
- Light Weight.
- Vibration Resistant with included Shock absorbers.
- Shock Absorber material: Synthetic Rubber.
- Universal Fiber Mount Shock Absorber Plate for flight controllers
- Compact design
- Super lightweight
- Mounting holes on the bottom makes it easy to install
- Suit for different open-source flight controller, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4
- Weight: 2gm
Ardupilot Mega APM 2.8 Flight Controller
- Model: APM 2.8
- Input Voltage (V): 12-16 V.
- Processor: ATMEGA2560 and ATMEGA32U-2
- Micro SD card slot: No.
- Arduino Compatible
- MPU6000 : 3-Axis MEMS Gyroscope + accelerometer
- High-performance Barometer upgraded to MS5611-01BA03, from Measurement Specialties.
- Support hundreds of 3D waypoints
- Full mission scripting with point-and-click desktop utilities
- Two-way telemetry and in-flight command using the powerful MAVLink protocol
- Powerful Ground Control Software
- Supports full "hardware-in-the-loop" simulation with Xplane and Flight Gear
- On-board 4 Megabyte Data flash chip for automatic data logging.
- Optional off-board GPS, an uBlox LEA-6H module with Compass.
- Dimensions: 70 x 45 x 15mm
- Weight: 70gm
Blade Propeller for 8520 8.5x20mm
- Length: 8.5″.
- Pitch: 20″.
- Diameter: 55mm
- Centre hole diameter: 0.97mm
- Colour : Black & Red
- suitable for 90mm-150mm DIY Micro Quadcopter Frame Kits
- Suitable for 1mm shaft diameter Coreless motor 7*16mm, 7*20mm, 8.5*20mm
- Suitable for 1mm shaft diameter Carbon Brush motor N20, M20, N30
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
CC3D flight Control
- Powerful STM32 32-bit microcontroller running at 90 MIPS with 128KB Flash and 20KB RAM.
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Supported by powerful OpenPilot GCS
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spectrum satellite receiver support.
- Futaba S-BUS hardware support.
- With a function of being directly plugged into the satellite receiver
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits on-board EEPROM for configuration storage.
CYS-S8218 40 kg High Torque Digital Servo
- Control System: Pulse Width Control 1500usec Neutral
- High precision metal gear
- Suit for 1/5 RC car
- Material: aluminum alloy
- Operating Voltage: 6.0~7.4Volts
- Operating Temperature Range: (-)10 to +50 degree C
- Operating Speed (6.0V): 0.20sec/60° at no load
- Operating Speed (7.4V): 0.18sec/60° at no load
- Stall Torque (6.0V): 36kg.cm
- Stall Torque (7.4V): 38kg.cm
- Operating Temperature Range: (-)10 to +50 degree C
- Dead Band Width: 4usec
- Motor Type: NdFeB motor
- Bearing Type: Dual Ball Bearing
- Connector wire: about 300mm
- Size: 59.5*29*55.2mm
- Weight: 164g
DC 3.7V 7mm x 16mm Magnetic Micro Coreless Motor + Propeller
DC 3.7V Coreless Motor + Propeller 7×20
DIY D2-5 Intelligent Tracing Car Kit
- Model: D2-5
- Name: D2-5 Intelligent Tracking Car DIY Kit
- PCB Size:104*72*1.6mm
- Installation dimension:104*72*55mm
- Work Voltage:3V
- Easy to Assemble
- The battery is not included
- Self-assembly required
- Without the battery.
- Mini Size, convenient to store and carry
- It can improve children's abilities of creativity and practice
- Material: ABS