Blade Propeller for 8520 8.5x20mm
- Length: 8.5″.
- Pitch: 20″.
- Diameter: 55mm
- Centre hole diameter: 0.97mm
- Colour : Black & Red
- suitable for 90mm-150mm DIY Micro Quadcopter Frame Kits
- Suitable for 1mm shaft diameter Coreless motor 7*16mm, 7*20mm, 8.5*20mm
- Suitable for 1mm shaft diameter Carbon Brush motor N20, M20, N30
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
CC3D flight Control
- Powerful STM32 32-bit microcontroller running at 90 MIPS with 128KB Flash and 20KB RAM.
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Supported by powerful OpenPilot GCS
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spectrum satellite receiver support.
- Futaba S-BUS hardware support.
- With a function of being directly plugged into the satellite receiver
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits on-board EEPROM for configuration storage.
CYS-S8218 40 kg High Torque Digital Servo
- Control System: Pulse Width Control 1500usec Neutral
- High precision metal gear
- Suit for 1/5 RC car
- Material: aluminum alloy
- Operating Voltage: 6.0~7.4Volts
- Operating Temperature Range: (-)10 to +50 degree C
- Operating Speed (6.0V): 0.20sec/60° at no load
- Operating Speed (7.4V): 0.18sec/60° at no load
- Stall Torque (6.0V): 36kg.cm
- Stall Torque (7.4V): 38kg.cm
- Operating Temperature Range: (-)10 to +50 degree C
- Dead Band Width: 4usec
- Motor Type: NdFeB motor
- Bearing Type: Dual Ball Bearing
- Connector wire: about 300mm
- Size: 59.5*29*55.2mm
- Weight: 164g
DC 3.7V 7mm x 16mm Magnetic Micro Coreless Motor + Propeller
DC 3.7V Coreless Motor + Propeller 7×20
DIY D2-5 Intelligent Tracing Car Kit
- Model: D2-5
- Name: D2-5 Intelligent Tracking Car DIY Kit
- PCB Size:104*72*1.6mm
- Installation dimension:104*72*55mm
- Work Voltage:3V
- Easy to Assemble
- The battery is not included
- Self-assembly required
- Without the battery.
- Mini Size, convenient to store and carry
- It can improve children's abilities of creativity and practice
- Material: ABS
Eachine RatingKing F14 1000TVL CCD 110 Degree Mini FPV Camera 411008 1/14 RC Car Part
- Brand: Eachine.
- Item: 1000TVL CCD 110 Degree Mini FPV Camera 411008.
- Input Voltage: 5V.
- Power Consumption: 55mA@ 5v.
- Lux: 0.08Lux/ F1.2.
- Sensor: 1/3 "CCD.
- Format: NTSC/PAL (Free switch).
- Resolution: Ultra High Definition 1000TVL.
- PAL: 976H X 582V.
- NTSC: 976H X 494V.
- Lens: 2.8mm IR coated.
- FOV: 110 °.
- Operating temperature: 0 to 40°C.
- With 1/3'' CCD sensor.
- With lens cover,well protecting the lens.
- With WRD function in default.
- Without OSD.
- Super lightweight, ultra-low power consumption
- Camera size: 28 * 24.5 * 17.5mm.
- Len Size: 17mm *14mm.
- Net Weight: 10g
EMAX BLHELI 12Amp ESC for Quadcopter / Drones
- Based on BL Heli firmware.
- ESC Type: Brushless.
- Built in linear or switched BEC.
- Constant Current: 12A
- Burst Current: 15A
- BEC Mode: Linear BEC : 5v / 1A
- Lipo Cells: 2-4
- Constant Current: 12A.
- Support: One-shot 125 Protocol.
- Includes low voltage protection, over heat protection, and self-check functions.
- Separate power supply for MCU and BEC, helping eliminate magnetic interference.
- Fully programmable by any standard programming card or directly from your transmitter.
- Customisable throttle range.
- Weight: 11g
- Dimension: 42x20x8mm
F450 Quadcopter Frame
- Model: F450
- Frame width: 450mm
- Frame height: 55mm
- Frame Weight: 282g
- Take-off Weight: 800g ~ 1200g
- Motor Mount Bolt Holes: 16/19mm
- Landing Gear Height: 150mm
- Landing Gear Weight: 90gm
- Made by advanced engineering material, super strong & smooth.
- High quality and strong ability of anti-fall, lower maintenance cost.
- Compact design with small numbers of components, you can assemble it by yourself quickly and easily.
- Recommended Propeller: 10x4.5in;8x4.5in
- Recommended Battery: 3S~4S LiPo
- Recommended Motor: 22x12mm (Stator size)
- Recommended ESC: 20A/30A ESC