AfroFlight Naze32 Rev6 Flight Controller Board
- Version: 6 DOF
- Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line
- USB on right side
- 32-bit processor running at 3.3V/72MHz (STM32F103CB).
- Up to 8 Ch. RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spectrum satellite receivers
- Built-in FrSky telemetry inverter
- Battery voltage monitoring
- SBUS Inverter built-in
- Spectrum satellite
- Modern GUI for all operating systems, Baseflight Configurator.
- Supports multiple platforms: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
- MPU6500 : 3-Axis MEMS Gyroscope + accelerometer
- Onboard MicroUSB for setup and configuration
- BMP280 barometer
- Modern GUI for all operating systems, Baseflight Configurator.
- Sonar pads w/resistors added for direct connection to 5V sonar3.3V
- Dimensions: 36x36 mm (30.5mm Mounting)
- Weight: 5.3 grams (no headers, 7.3 grams with).
Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
- Colour: Black
- Material: Glass Fibre
- Upper Frame size:90x60x2mm
- Lower Frame Size: 100x70x2mm
- Shock absorber Height: 10×12mm
- Light Weight.
- Vibration Resistant with included Shock absorbers.
- Shock Absorber material: Synthetic Rubber.
- Universal Fiber Mount Shock Absorber Plate for flight controllers
- Compact design
- Super lightweight
- Mounting holes on the bottom makes it easy to install
- Suit for different open-source flight controller, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4
- Weight: 2gm
DC 3.7V 7mm x 16mm Magnetic Micro Coreless Motor + Propeller
EMAX BLHELI 12Amp ESC for Quadcopter / Drones
- Based on BL Heli firmware.
- ESC Type: Brushless.
- Built in linear or switched BEC.
- Constant Current: 12A
- Burst Current: 15A
- BEC Mode: Linear BEC : 5v / 1A
- Lipo Cells: 2-4
- Constant Current: 12A.
- Support: One-shot 125 Protocol.
- Includes low voltage protection, over heat protection, and self-check functions.
- Separate power supply for MCU and BEC, helping eliminate magnetic interference.
- Fully programmable by any standard programming card or directly from your transmitter.
- Customisable throttle range.
- Weight: 11g
- Dimension: 42x20x8mm
Mini OSD W/ KV Team MOD For Racing F3 Naze32 Flight Controller RC Drone
- NO DC/DC converter, hence less heating
- FTDI cable compatible pinout
- Standard 6-pin ISP header
- Two LED indicators
- ATmega328P with Arduino bootloader
- MAX7456 monochrome on-screen display
- Pad for an Analog or Digital PWM RSSI signal
- Pad for the connection of a Current Sensor
- ATmega328P with Arduino bootloader
- Standalone, or with APM / Flip / Flip32+ flight controllers
- These modifications allow direct connection of two batteries (up to 4S)
- This hardware takes the hardware mods for this firmware and builds them into an RTF solution.
- This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
- Two independent power sections with an LED indicator on each.
- Solder jumpers for combining the power sections
- Solder jumper for PAL video option
- +5V 500mA regulator for up to +12V supply input
- Exposed test points for HSYNC and LOS ATmega328P with Arduino bootloader.
- Dimension: 16 x 16mm
Landing Gear
Power Distribution Board
- Material: glass fiber
- Easy connections from the battery to your ESC, video Transmitter, Flight Controller,
- LED power indicators Â
- Switches to control LEDs, video Transmitter power, etc.
- Can connect 1-8 ESC.
- Onboard switching voltage regulator
- Hole Spacing: 45mm Square and 35mm Square (Compatible with KK 45mm spacing)
- Dimensions : 50 x 50 x 2 mm.
- Weight: 8 gm.
Q330 Quadcopter Frame
- Colour: Black & Red
- Wheelbase: 325mm
- Frame Diameter: 330mm
- Frame Spacing: 30mm
- Recommend to use 3S 2200-4000mah Lipo battery
- Glass fibre material on centre plates
- Glass-filled nylon arms for increased strength and durability
- Lightweight arm design
- Integrated PDB for easy wiring and tidy installation
- Increased internal space for additional electronics/equipment
- Additional mounting holes for frame upgrades
- Suitable for CC3D\MWC\APM\PIXHAWK\NAZA flight control
- Recommend to use 2204/2205 + 6045propeller + 12A ESC, violate flying recommend to use 2208 motor + 20A ESC + 8045 propeller
- Dimension: 21.5*10.5*5cm
- Weight: 231g
5045(5×4.5) SF Propellers 2CW+2CCW-1pair
- Length: 5″.
- Pitch: 4.5″.
- Weight: 22 gm.
- Shaft diameter: 5mm.
- Total length: Â 5 inch / 125 mm.
- Material: Glass Fiber Nylon
- Durable plastic construction provides both lightness and rigidity.
- Â 5045(5X4.5) Glass Fiber Nylon Bullnose Black Propellers comes with an Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
8045(8×4.5) SF Propellers 2CW+2CCW-pair
- Length: 8″.
- Pitch: 4.5″.
- Weight: 14 gm.
- Shaft Diameter: 5Â mm.
- Total Length: 8 inch / 220 mm.
- Material: Glass Fiber Nylon
- Comes with thin and wide blades
- 8045(80×4.5) SF Propellers Black features an epoxy resin cover.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
6045(6×4.5) Propeller
- Length: 6″.
- Pitch: 4.5″.
- Shaft Diameter: 5mm.
- Total length: 6 inch / 150 mm.
- Material: Glass Fiber Nylon
- It includes a set of plastic reducers(3, 4, 5, 6 mm)
- Durable plastic construction provides both lightness and rigidity.
- Â 6045(6X4.5) Glass Fiber Nylon Propeller comes Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
1245(12X4.5) Propeller
- Length: 12″
- Pitch: 4.5″
- Weight: 36.5g
- Shaft Diameter: 6mm
- Total Length: 30.5cm
- Material: ABS
- Durable plastic construction provides both lightness and rigidity.
- Â 1245(12X4.5) Carbon Fiber Black comes with an Epoxy resin cover.
- Very strong and lightweight.
- Includes a set of reducers 3, 4, 5, 6,
- Quick to release, quick to attach
- Provides greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 28gm