Pixhawk 2.4.8 Drone Flight Controller PX4 32 Bit Autopilot
- The advanced 32-bit ARM CortexM4 high-performance processors; can run NuttX RTOS real-time operating system.
- 14 PWM / servo output.
- Bus interface (UART, I2C, SPI, CAN).
- The integrated backup power and backup controller fails; the primary controller fails over to the backup control is safe.
- Provide automatic and manual modes.
- Provide redundant power input and failover.
- Multicolor LED lights.
- Provide a multi-tone buzzer Interface.
- Micro SD card to record flight data.
- 32bit STM32F427 Cortex M4 core with FPU.
- 32-bit STM32F103 failsafe co-processor.
- 168 MHz.
- 128 KB RAM.
- 2 MB Flash.
- ST Micro L3GD20H 16 bit gyroscope.
- ST Micro X4HBA 303H 14-bit accelerometer/magnetometer.
- Invensense MPU 6000 3-axis accelerometer/gyroscope.
- MEAS MS5607 barometer.
- 5* UART, 1*compatible high voltage, 2*hardware flow control
- 2*CAN
- Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
- Futaba SBUS compatible input and output
- PPM signal input
- RSSI (PWM or voltage) input
- I2C
- SPI
- 3.3 and 6.6VADC
- input External USB MICRO interface
- Color:Black
- Size: 50x81x16mm
Blade Propeller for 8520 8.5x20mm
- Length: 8.5″.
- Pitch: 20″.
- Diameter: 55mm
- Centre hole diameter: 0.97mm
- Colour : Black & Red
- suitable for 90mm-150mm DIY Micro Quadcopter Frame Kits
- Suitable for 1mm shaft diameter Coreless motor 7*16mm, 7*20mm, 8.5*20mm
- Suitable for 1mm shaft diameter Carbon Brush motor N20, M20, N30
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
- Colour: Black
- Material: Glass Fibre
- Upper Frame size:90x60x2mm
- Lower Frame Size: 100x70x2mm
- Shock absorber Height: 10×12mm
- Light Weight.
- Vibration Resistant with included Shock absorbers.
- Shock Absorber material: Synthetic Rubber.
- Universal Fiber Mount Shock Absorber Plate for flight controllers
- Compact design
- Super lightweight
- Mounting holes on the bottom makes it easy to install
- Suit for different open-source flight controller, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4
- Weight: 2gm
DC 3.7V Coreless Motor + Propeller 7×20
DC 3.7V 7mm x 16mm Magnetic Micro Coreless Motor + Propeller
Motor for Micro FPV RC Quadcopter
EMAX BLHELI 12Amp ESC for Quadcopter / Drones
- Based on BL Heli firmware.
- ESC Type: Brushless.
- Built in linear or switched BEC.
- Constant Current: 12A
- Burst Current: 15A
- BEC Mode: Linear BEC : 5v / 1A
- Lipo Cells: 2-4
- Constant Current: 12A.
- Support: One-shot 125 Protocol.
- Includes low voltage protection, over heat protection, and self-check functions.
- Separate power supply for MCU and BEC, helping eliminate magnetic interference.
- Fully programmable by any standard programming card or directly from your transmitter.
- Customisable throttle range.
- Weight: 11g
- Dimension: 42x20x8mm
Power Distribution Board
- Material: glass fiber
- Easy connections from the battery to your ESC, video Transmitter, Flight Controller,
- LED power indicators Â
- Switches to control LEDs, video Transmitter power, etc.
- Can connect 1-8 ESC.
- Onboard switching voltage regulator
- Hole Spacing: 45mm Square and 35mm Square (Compatible with KK 45mm spacing)
- Dimensions : 50 x 50 x 2 mm.
- Weight: 8 gm.