ADG509 4-Channel Analog Multiplexer IC
- 4 Channel Analog Multiplexer
- Power Supply Type: Single/Dual
- Supply Voltage Range (Single): 10.8V to16.5V
- Supply Voltage Range(Dual): ±10.8V to ±16.5V
- High Level Output Current Max. : 20mA
- Power Dissipation Max. : 470mW
- Propagation Delay Max.: 300ns
- On Resistance Max.: 700Ω
- Supply Current Max.: 1.5mA
- Package: DIP-16
DS18B20 Programmable Resolution 1-Wire Digital Thermometer IC
74LS76 Dual J-K Flip-Flop IC with Set and Clear
ICL8038CCPD Precision Waveform Generator or Voltage Controlled Oscillator IC
- Precision Waveform Generator or Voltage Controlled Oscillator
- Power Supply Type: Single/Dual
- Supply Voltage Range (Single): 10V to 30V
- Supply Voltage Range(Dual): ±5V to ±15V
- Output Sink Current: 25mA
- Frequency of Oscillation Max.: 100kHz
- Supply Current Max.: 20mA
- Duty Cycle: 2% to 98%
- FM Linearity:0.5%
- Rise Time: 180ns
- Fall Time: 40ns
- Package: DIP-16
PIC16F873A Microcontroller IC
- Maximum CPU Frequency: 20 MHz
- Architecture: 8 bit
- Program Memory (Flash): 7 kB
- RAM: 192 byte
- Internal Oscillator: No
- ADC: 1 (5 channels)
- of Pins: 28
- Voltage: 2V - 5.5V
- 100,000 erase/write cycle Enhanced Flash program memory typical
- 1,000,000 erase/write cycle Data EEPROM memory typical
- Data EEPROM Retention > 40 years
- Self-reprogrammable under software control
- In-Circuit Serial Programming™ (ICSP™) via two pins
- Single-supply 5V In-Circuit Serial Programming
- Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
- Programmable code protection
- Power saving Sleep mode
- Selectable oscillator options
- In-Circuit Debug (ICD) via two pins
- Low-power, high-speed Flash/EEPROM technology
- Fully static design
- Wide operating voltage range (2.0V to 5.5V)
- Commercial and Industrial temperature ranges
- Low-power consumption
LM1876 Dual 20W Audio Power Amplifier IC
- Dual 20W Audio Power Amplifier with Mute and Standby Modes
- Spike Protection
- Minimal amount of external components necessary
- Quiet fade-in/out mute mode
- Standby-mode
- Isolated 15-lead TO-220 package
- THD+N at 1 kHz at 2 x 15W continuous average output power into 4Ω or 8Ω: 0.1% (max)
- THD+N at 1 kHz at continuous average output power of 2 x 20W into 8Ω: 0.009% (typ.)
- Standby current: 4.2 mA (typ.)
PIC16F84A Microcontroller IC
- Maximum CPU Frequency: 20 MHz
- Architecture: 8 bit
- Program Memory (Flash): 1.75 kB
- RAM: 68 byte
- Internal Oscillator: No
- ADC: No
- of Pins: 18
- Voltage: 2V - 6V
- 10,000 erase/write cycles Enhanced FLASH Program memory typical
- 10,000,000 typical erase/write cycles EEPROM Data memory typical
- EEPROM Data Retention > 40 years
- In-Circuit Serial Programming™ (ICSP™) - via two pins
- Power-on Reset (POR), Power-up Timer (PWRT), Oscillator Start-up Timer (OST)
- Watchdog Timer (WDT) with its own On-Chip RC Oscillator for reliable operation
- Code protection
- Power saving SLEEP mode
- Selectable oscillator options
- Low power, high speed technology
- Fully static design
- Wide operating voltage range:
- Low power consumption:
PIC16F887 Microcontroller IC
- Architecture: 8 bit
- Program Memory (Flash): 14 kB
- RAM: 368 byte
- Internal Oscillator: 8 MHz, 32 KHz
- ADC: 1 (14 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- Precision Internal Oscillator:
- Power-Saving Sleep mode
- Wide operating voltage range (2.0V-5.5V)
- Industrial and Extended Temperature range
- Power-on Reset (POR)
- Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR) with software control option
- Enhanced low-current Watchdog Timer (WDT) with on-chip oscillator (software selectable nominal 268 seconds with full prescaler) with software enable
- Multiplexed Master Clear with pull-up/input pin
- Programmable code protection
- High Endurance Flash/EEPROM cell:
- Program memory Read/Write during run time
- In-Circuit Debugger (on board)
74LS922 16-Key Encoder IC
74C926 4-Digit Counter IC
- 4-Digit Counter With Multiplexed 7-Segment Output Drivers
- High-level input voltage: 2V
- Low-level input voltage: 0.8V
- High-level output voltage: 2.4V
- Low-level output voltage: 0.4V
- Output source current: -2mA
- Maximum clock frequency: 4MHz
- Input capacitance: 5pF
- Supply voltage range: 3V to 6V
- Package: DIP-18
