Showing 1–12 of 22 results

Leadshine DMA860H

₹8,500.00 inc. GST
  • Input voltage: Up to +80VAC or +110VDC.
  • Output current Up to 7.2A.
  • Pulse input frequency up to 300 KHz.
  • Automatic idle-current reduction.
  • Over-voltage, over-current protection.
  • Suitable for 2-phase and 4-phase motors.
  • Support PUL/DIR and CW/CCW modes.
  • Operating Temperature : 70 C.
  • High performance, cost-effective
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • TTL compatible and optically isolated input
  • 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
 

Leadshine DMA860E Stepper Motor Driver

₹5,700.00 inc. GST
  • Model: DMA860E.
  • Control Mode: Step & Direction.
  • Max Input Frequency: 200 kHz.
  • Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
  • Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
  • Number of DIP Switch Resolution Configurations: 16.
  • 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
  • 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
  • Logic Current Range: 7-16mA (10mA typical).
  • Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
  • Pulse enabled at: Rising edge.
  • Idle Current Percentage: 50 %.
  • Number of Digital Inputs: 3.
  • Step Width: 2,500 ns.
  • Minimal Direction Setup Time: 5,000 ns.
  • Isolation Resistance: 500M Ohm..
  • Ambient Temperature: 0-50°C.
  • Humidity: 40–95% RH.
  • Operating Temperature: 0-70°C.
  • Vibration: 5.9 m/s2 Max.
  • Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
  • Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
  • Opto Isolation for input control signals.
  • Soft-start with no “jump” when powered on.
  • Protections for over-voltage and over-current.
  • Dimension: 5.94 X 3.82 X 2.24 Inches.
  • Weight: 1.13 lbs.
   

Leadshine DM320C

₹5,500.00 inc. GST
  • Supply voltage up to +30 VDC
  • Output current programmable, from 0.3A to 2.0A
  • Pulse input frequency up to 70 kHz
  • TTL compatible and optically isolated input
  • Automatic idle-current reduction
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Anti-Resonance provides optimum torque and nulls mid-range instability
  • Self-test and Auto-configuration technology offers optimum responses with different motors
  • Microstep resolutions programmable, from full-step to 102,400 steps/rev
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness

Leadshine DM542

₹4,500.00 inc. GST
  • Good high-speed performance
  • Supply voltage up to +50VDC
  • Output current up to 4.2A
  • Pulse frequency up to 300 KHz
  • Extremely cost-effective
  • Automatic idle-current reduction
  • 3-state current control technology
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • TTL compatible and optically isolated input
  • 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
  • Suitable for 2-phase and 4-phase motors
  • DIP switch current setting with 8 different values
  • Support PUL/DIR and CW/CCW modes
  • Short-voltage, over-voltage, over-current protection

DM556 Digital Stepper Motor Driver with Micro Stepping 20 to 50V 5.6A

₹4,000.00 inc. GST
  • Good high-speed performance
  • Supply voltage: +50VDC
  • Output current from 0.5A to 5.6A
  • Pulse input frequency up to 200 kHz
  • Extremely cost-effective
  • Automatic idle-current reduction
  • Self-test and Auto-configuration technology TTL compatible and optically isolated input
  • Micro step resolutions programmable, from full-step to 102,400 steps/rev
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Anti-Resonance provides optimum torque and nulls mid-range instability
  • Extra-low motor noise offers excellent quietness
  • Over-voltage, over-current protection and phase error protection

“PWM Generator Module for Stepper Motor Driver with Forward and Reverse Function “

₹1,550.00 inc. GST
  • Board can be used to generate PWM signals for the stepper motor driver
  • Operating Voltage: 12VDC
  • Three Frequency Range
  • Forward and Reverse Function.
  • It has three frequency ranges selectable via onboard jumpers.
  • Frequency can be measured via PUL and common cathode (GND) ports.
  • The board has two sets of power input

MACH3 interface board

₹1,350.00 inc. GST
  • Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
  • Driver type - Pulse and Direction signal control
  • Wide input voltage range: 12-24V, and with anti-reverse function.
  • Output 0-10V analogue voltage for the inverter to control the spindle speed.
  • Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
  • USB power supply and peripherals power phase are separate to protect computer security.
  • All the signals are to-isolate which can protect your computer security.
  • 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
  • Wide input voltage range: 12-24V, and with anti-reverse function.
  • One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
  • Maximum support 5-axis stepper motor driver controllers
  • Output 0-10V analogue voltage for the inverter to control the spindle speed.
  • All the way to the relay output port, control spindle switch. Output port P17 mouth.
  • One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
  • Weight - Approx. 75g
  • Dimensions - 90 * 70 * 20mm

TB6560 CNC 3 Axis Stepper Motor Driver Controller Board

₹970.00 inc. GST
 

TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor

₹970.00 inc. GST
  • Supply voltage up to +32 VDC
  • Output current up to 3.0A
  • Pulse frequency up to 20 KHz
  • Suitable for 2-phase and 4-phase motors
  • Over-voltage and short-circuit protection
  • 7 output current choices, max 3200 steps/rev
  • Automatic idle-current reduction
  • Single-chip motor driver for sinusoidal micro-step control of stepping motors
  • High output withstands voltage due to the use of BiCD process:
  • Forward and reverse rotation
  • Selectable phase excitation modes (2, 1-2, 2W1-2, and 4W1-2)
  • High output withstand voltage: VDSS = 40 V
  • High output current: IOUT = TB6560AHQ: 3.5 A (peak)
  • Internal pull-down resistors on inputs: 100 kΩ
  • Output monitor pin: MO current (IMO (max) = 1 mA)
  • Reset and enable pins

L298P Motor Shield motor driver

₹850.00 inc. GST
  • L298P based Arduino motor driver shield
  • Operating Voltage 5V to 12V
  • Motor controller L298P, Drives 2 DC motors or 1 stepper motor
  • The logical part of the input voltage VD: 5V
  • Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input
  • The logical part of the work current Iss:<36mA
  • Driven part of the operating current Io:<2A
  • Current sensing 1.65V/A
  • Free running stop and brake function
  • Maximum power dissipation: 25W (T = 75 Celsius)
  • Max current 2A per channel or 4A max (with external power supply)
  • Control signal input level: High 2.3V
  • Onboard Bluetooth interface, you can directly plug, no wiring required.
  • The board with L298P motor drive chip, directly with the motherboard digital I/O port (D10, D11, D12, D13), without cumbersome wiring.
  • Onboard buzzer (D4), you can set the reverse alarm ringtones.
  • D2, D3, D5, D6, D7, D9 are not occupied by the digital interface.
  • A 0 – A 5 six analogue interfaces.
  • Forward and Backward steering are indicators
 

16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi

₹600.00 inc. GST
  • Adjustable frequency PWM up to about 1.6 kHz
  • 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
  • Configurable push-pull or an open-drain output
  • The output enable pin to quickly disable all the outputs
  • Terminal block for power input
  • Reverse polarity protection on the terminal block input
  • Green power-good LED
  • 3 pin connectors in groups of 4 so you can plug in 16 servos at once
  • Chainable design
  • A spot to place a big capacitor on the V+ line
  • 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
  • This board/chip uses an I2C 7-bit address between 0x60-0x80, selectable with jumpers.

5-36v Switch Drive High-power MOSFET Trigger Module

₹400.00 inc. GST
 
  • Operating Voltage: DC 5V - 36V;
  • The trigger source: digital high-low (DC3.3V - 20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal frequency 0--20KHZ perfect support.
  • Output capacity: DC 5V - 36V, at room temperature, continuous current 15A, power 400W! Lower auxiliary cooling conditions, the maximum current up to 30A.
  • Applications: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc.. You can enter
  • PWM, motor speed control, lamp brightness.
  • Availability: unlimited switch
  • Operating temperature: -40-85
  • Dimension: 34mm x 17mm x 12mm
  • The use of imported dual-MOS parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment
  • Wide voltage, the perfect support for PWM
  • Easily control high power devices
  • Input PWM to achieve motor speed control, lamp brightness control