3 Channel Infrared White/Black Line Detection Module – Proximity Sensor
- Input voltage: 3.0 V – 5.5 V
- High accuracy for tracking Black/White lines.
- Distance sensor at the front, distance can be adjusted
- Special touch sensor design, making the robot design simple
- Output form: digital output (high and low level)
- Indicator LEDs
- Onboard potentiometer to adjust the sensitivity
- Detection distance: 0 – 4 cm (black and white line sensors), 0 – 5 cm (adjustable distance detection)
APDS-9930 Gesture Sensor Digital Proximity And Ambient Light Sensor For Arduino
- Working voltage:2.8-3.8V
- ALS, IR LED, and Proximity Detector in an Optical Module
- Approximates Human Eye Response
- Programmable Interrupt Function with Upper and Lower Threshold
- Programmable range from 2.7 ms to more than 8 seconds
- Up to 16-Bit Resolution
- High Sensitivity Operates Behind Darkened Glass
- Low Lux Performance at 0.01 lux;
- Ambient Light Sensing (ALS)
- Proximity detection
- I2C interface is compatible up to 400kHz (I2C fast mode) –
Infrared Ir Obstacle Avoidance Detector Sensor Module Adjustable 2-180cm
- Power requirements: 5 VDC
- Communication: Digital High/Low Output
- A variety of welding methods, vertical and horizontal, to expand the scope of application
- Add precision potentiometer to adjust infrared 38KHz detection range
- Sensor detection with enabling the port, convenient signal line as bus application line
- Power-on enable port default level, the sensor enables the detection output signal
- Detection range up to 1.2 meters
- Software enhancement, setting can avoid infrared light interference of the same module or other kinds of infrared remote control devices
- Working condition of each module recorded with EEPROM, reduce the probability of mutual interference of the same paragraph to 1%
- Signal low output
- Pin SIP header, applied in breadboard or through-hole project
- On-board set jumper JP, the signal output has a latch function when shorted, otherwise, it is jog output
- Operating temperature: 32 to 158 ° F (0 to +70 ° C)
- Size: 2.4cm × 2.8cm
IR Infrared Obstacle (Imported)
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
IR Obstacle Avoidance Proximity Sensor Module
IR Proximity Module using TSOP
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
IR-08H Infrared Obstacle Avoidance Sensor Module
- Infra-Red IR Emission Receiver IR-08H for Arduino
- Onboard with HS0038B HS38B IR receiver
- Operating Voltage: 3V – 5.5V
- Detection range : 2cm – 40cm
- Output level: Low logic level when an obstacle is detected
- Working current: 20mAh
- Working temperature: -10’C~+50’C
- IO interface: 4 line (-/+/S/EN)
- Output signal: TTL Level
- Adjusting mode: Multi resistance regulation
- Effective angle: 35°
- Size: 4.5 * 1.1cm(approx)
- Easy to assemble and use
- On-board detection indication
- Pin Connection to the board: 4 pins
- A pre-set knob to fine-tune distance range
LJ12A3-4-Z/BY PNP DC6-36V 8 mm INDUCTIVE PROXIMITY SENSOR
- Output type: PNP NO
- Supply voltage: 6V-36V
- Current output: 300mA
- Response frequency: 0.5khz
- Detecting distance: 4mm
- Wire type: cylindrical DC 3 wire type
- Switch appearance type: cylinder type
- Operating temperature: -25 degrees to 55 degrees Celsius
- Detect object: iron
- Red led checks proximity status
- High repeated positioning accuracy
- High switching frequency
- Reverse power protection, short circuit protection, directly connecting with PLC
- anti-vibration, dust, water, and oil prevention
- Dimension: 5*3*3cm
- Weight: 400gm
RIKO SN04-N NPN Inductive Proximity Sensor
• Operating Voltage(V): 10 ~30
• Current Consumption Max: 5 mA
• Detection distance(mm): 5 mm.
• Type of detection: Inductive.
• Cable Length: 145 cm.
• Response Frequency: 500Hz Max.
• Protection class: IP 67
• Red LED checks the state of the proximity sensor
• High repeated positioning accuracy
• High switching frequency
• Wide voltage range
• Antivibration, dust, water and oil prevention
• Reverse power protection, short circuit protection, directly connecting with PLC
• It can replace small switches and limit switches