I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-14%
BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
Original price was: ₹1,500.00.₹950.00Current price is: ₹950.00. inc. GST
TL866CS USB Universal Programmer EEPROM FLASH 9 Adapters Extractor for 13000 Ics
Original price was: ₹7,525.00.₹5,000.00Current price is: ₹5,000.00. inc. GST
L9110 DC Stepper Motor Driver Board H-Bridge
Original price was: ₹350.00.₹300.00Current price is: ₹300.00. inc. GST
- Low static work current
- Power supply voltage: DC2.5-12V
- Each channel has 800mA continuous current output
- Low saturation pressure drop
- TTL/CMOS output level compatible can be connected directly to the CPU
- Output built-in clamping diode, apply to the perceptual load
- Control and drive integrated into IC
- Have pin high-pressure protection function
- Working temperature: 0-80 °C
Description
The L9110S dual-channel h-bridge motor driver module designed as a compact board used to drive small robots. This module based on the L9110 Motor Driver IC. This L9110S dual-channel H-bridge motor driver consists of two independent motor driver chips in which each capable of driving a continuous current up to 800mA. The boards operate at a voltage range from 2.5 V to 12 V enabling this module to used with both 3.3 Volts and 5 Volts microcontrollers. A set of female header pins provided to connect this module to a microcontroller. The motors easily attached via two sets of screw terminals.
The speed of the motor is controlled by a PWM Pulse Width Modulation signal and a digital output is used to change its direction. This module also used to drive a single four-line two-phase stepper motor. This module can be easily mounted onto your robot or other projects via four holes provided on the board.
Instructions:
- VCC external 2. 5V-12V voltage, GND external GND
- IA1 external MCU 10 port
- IB1 external MCU 10 port
- IA2 external MCU 10 port
- IB2 external MCU 10 port
- 0A1, 0B1Â connected to 2 pins of DC motor, no direction
- 0A2, 0B2 connected to 2 pins of DC motor, no direction
- Turn on VCC, the GND module power indicator is on.
- IA1 input high level, IB1 input low level, [0A1 0B1] motor forward
- IA1 input low level, IB1 input high level, [0A1 0B1] motor reverse
- IA2 input high level, IB2 input low level, [0A2 0B2] motor forward
- IA2 input low level, IB2 input high level, [0A2 0B2] motor reverse
Reviews (0)
Shipping & Delivery
Related products
“PWM Generator Module for Stepper Motor Driver with Forward and Reverse Function “
- Board can be used to generate PWM signals for the stepper motor driver
- Operating Voltage: 12VDC
- Three Frequency Range
- Forward and Reverse Function.
- It has three frequency ranges selectable via onboard jumpers.
- Frequency can be measured via PUL and common cathode (GND) ports.
- The board has two sets of power input
DM556 Digital Stepper Motor Driver with Micro Stepping 20 to 50V 5.6A
- Good high-speed performance
- Supply voltage: +50VDC
- Output current from 0.5A to 5.6A
- Pulse input frequency up to 200 kHz
- Extremely cost-effective
- Automatic idle-current reduction
- Self-test and Auto-configuration technology TTL compatible and optically isolated input
- Micro step resolutions programmable, from full-step to 102,400 steps/rev
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Anti-Resonance provides optimum torque and nulls mid-range instability
- Extra-low motor noise offers excellent quietness
- Over-voltage, over-current protection and phase error protection
L298N MOTOR DRIVER
- Driver model: L298N 2A
- Driver chip: Double H bridge L298N
- Motor supply voltage: 46V(maximum)
- Motor supply current: 2A(maximum)
- Logic voltage: 5v
- Driver voltage: 5V-35V
- Driver current: 2A
- Logical current: 0-36mA
- Maximum power: 25W
- Current sensor for each motor
- LED indication for power status
- Heat sink for better performance
- Operating temperature: -25 degrees to 135 degrees Celsius
- Can be interfaced with simple manual switches, TTL logic gates, relays, etc.
- Dimension: 55*60*30mm
- Weight: 33gm
Leadshine DM320C
- Supply voltage up to +30 VDC
- Output current programmable, from 0.3A to 2.0A
- Pulse input frequency up to 70 kHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Anti-Resonance provides optimum torque and nulls mid-range instability
- Self-test and Auto-configuration technology offers optimum responses with different motors
- Microstep resolutions programmable, from full-step to 102,400 steps/rev
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness
TB6560 4 Axis Cnc Controller 4 Axis Stepper Motor Driver DSP Controlled 3.5A 24V
- Rated maximum output: ± 4.5A, 40V, Peak 5A, low output impedance, source 0.5?,
- the receiving end of 0.4?, low voltage shutdown, thermal parking and circulation.
- circuit protection. After I design, you can set the current output of 0.5A 1A 1.8A 2.5A.
- 3.3A 4A 4.5A to accommodate more and different motor Current.
- The drive is suitable software mach2, mach3, (mach3 have support WIN7 system), KCAM4 like.
TB6612FNG Dual Motor Driver Module 1A for Arduino/Other Microcontroller
- Driver Model: TB6612FNG
- Operating voltage: 2.7 V to 5.5 V
- Limited Maximum Voltage: 15V max
- Output current: 1.2A
- Maximum Current: 3.2A (peak)
- Number of Channels: 1
- Standby control to save power
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1 spaced pins
- Filtering capacitors on both supply lines
- Dimensions: 30 x 20 x 10mm
- Weight: 22 gm
Reviews
There are no reviews yet.