I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
STC-1000 220V AC All Purpose Digital Temperature Controller Module
₹1,100.00 Original price was: ₹1,100.00.₹999.00Current price is: ₹999.00. inc. GST
- Power supply: 220VAC±10%, 50/60Hz.
- Sensor Type: NTC Sensor
- Resolution: 0.1°C.
- Accuracy: ±1°C (-50 – 70°C).
- Sensor error delay: 1 minute.
- Power consumption: ≤3W.
- Front panel size : 75 x 34.5mm
- Mounting size: 71x 29mm.
- Sensor length: 1m (include the probe).
- Temperature Measuring Range: -50 to 90°C
- Storage temperature : -30 – 75°C;
- Relative humidity : 20% – 85%
- Output Relay Capacity : Heating: 10A/220VAC; Cooling: 10A/220VAC
- Mini temperature controller.
- With a clear LED display for better readability.
- Dual heating and cooling control.
- Automatic over-temperature alarm
- Relay output.
- Dimension: 75x 34.5x 85mm
This Temperature-controlled thermostat switch widely used to control the heating/cooling of an object. This is performed with the help of the NTC sensor to detect the temperature. This STC-1000 220V AC All-Purpose Digital Temperature Controller Thermostat Module offers high accuracy and précised measurements at a low cost. This module consists of two output ports where the equipment connected to heat or cool the test system.
It offers a high-temperature control precision of 0.1℃ with an accuracy of ±1°C (-50 – 70°C). It is capable of measuring temperature over the range -50℃ to 99℃ performed by NTC sensors. NTC Thermistors defined as non-linear resistors, that vary their resistance characteristics with temperature. Thus the NTC resistance will decrease as the temperature increases. The on-board LED display shows the temperature results clearly. This module used in a wide range of applications as it can be directly installed or embed in industrial control equipment panels, more conveniently and quickly.
Moreover, it features a stainless steel material probe of length 1m which makes it waterproof and is anticorrosive. And also all the delicate and sensitive components related to the module enclosed in ABS flame retardant housing as environmental protection. This module controls the temperature by setting the temperature setting value and the difference value, and thus Temperature calibration performed. Finally, the Auto Switch on the module switches the modes between cool and heat.
Application:
- Used in potential chemical contamination or electrical interference
- Used in Nuclear energy control systems, combustion systems, railroad systems, aviation systems
- Medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations
- Systems, machines, and equipment that could present a risk to life or property
- Temperature-controlled system such as Domestic freezer, water tanks, refrigerator, industrial chiller etc

Related products
2000W SCR VOLTAGE REGULATOR
Acrylic case for XH-W1209 temperature controller
AM2302 WIRED MODULE
- Low cost
- 3V to 5V power and I/O
- 5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
- 3 wires 23cm long (9")
- Dimensions: 27x 58.75 x 13.30mm
Floating Straight Automatic Water Level Control For Water Tank-14014449MG
- Automatic Control, Low Self-Complementary Water, Water Full Automatic Stop.
- Four Intakes, Large Volume Of Water.
- Beautiful Appearance, Small Size, Practical, Simple Installation.
- Without Electricity, Easy To Use, Long Life, Low Failure Rate, Saving Water Resources.
- Working Pressure Range: 0.2-10Kg.
- Applicable Medium: Clean Water.
- Applicable Medium Temperature: ≤70degree C
- Resistance to High-Temperature to Medium Temperature: 70degree to 120degree C
- Material: Nylon Pa66, Stainless Steel Screws, Food Grade Rubber.
- Diameter: Approx. 46Mm / 1.81Inch.
- Dimension: Approx. 83*71mm
Smart 3pin DHT11 Digital Temperature And Relative Humidity Sensor Module + PCB
- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0°C to 50°C
- Humidity Range: 20% to 90%
- Resolution: 1%RH humidity, temperature 1
- Accuracy: ±1°C and ±1%
- Low power consumption.
- The module can detect the surrounding environment of the humidity and temperature
- High reliability and excellent long-term stability
- The output from the digital output
- Has fixed bolt hole and easy installation
UNI T Infrared Thermometer UT30R
- Measurement range: 32 to 45 ° C.
- Resolution: 0.1 ° C.
- Test distance: 5-10 cm
- Accuracy : ± 0.3°C
- Measurement repeatability : 0.3°C
- Response time : 500 ms
- Optical measuring range : 5.5μm ~ 14.0μm
- Simple, fast and accurate IR thermometer
- Flashing arm at high temperature (more than 37.2 ° C)
- Single button operation
- LCD display with backlight for dark condition
- Auto data hold for 8s
- Auto power off
- Low voltage indication
- Option of Celsius/Fahrenheit
- Power-off memory function
XH-W1219 12V Digital Display Temperature Controller Module W/NTC Waterproof Temperature Sensor
XH-W1401 12V Digital Led Thermostat Module Temperature Controller With Display
- Model: XH-W1401
- Power Supply: DC12V
- Thermostat Range: -9℃ to 99℃
- Thermostat Accuracy: 1℃
- Output : Electric relay output ,capacity 220V 10A/12V 10A
- For cooling or heating temperature control
- Simple Temperature Sensor Module with 12V Relay
- Imported High-Speed single-chip microcomputer.
- Three Display output status indicator.
- Automatically judge heating and cooling according to set temperature.
- Used in various temperature control, water temperature control, incubators, etc.
- Refresh Rate: 0.5 Sec
- Dimension:” 78*55mm
- Weight: 0.040 kg

Reviews
There are no reviews yet.