I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
TOP258YN Off-line Switcher IC
₹80.00 Original price was: ₹80.00.₹75.00Current price is: ₹75.00. inc. GST
- Supply Voltage: -0.3-9V
- Output Voltage: 700 V
- Output current: 6.88A
- Power: 195W
- Switching Frequency-Max: 132 kHz
- Package: TO-220-7C
- Lowest cost, lowest component count switcher solution
- Stable in discontinuous or continuous conduction mode
- Source connected tab for low EMI
- Circuit simplicity and Design Tools reduce time to market
Power Integrations’ TOPSwitch-HX series employs the same tried-and-true TOPSwitch architecture. The TOP258YN switcher IC is a single CMOS chip that has a high voltage 700V power MOSFET, PWM control, fault protection, and other control circuitry. This IC has a number of novel capabilities that help to lower system costs while also improving design flexibility, performance, and energy efficiency.
Based on package type, either 1 or 3 additional pins over the TOPSwitch standard DRAIN, SOURCE and CONTROL terminals. This allow the certain features such as line sensing (OV/UV, line feed-forward/DCMAX reduction), accurate externally set current limit, remote ON/OFF. Moreover, it also offers a synchronization to an external lower frequency, and frequency selection (132 kHz/66 kHz).
Soft-start, 132 kHz switching frequency (automatically lowered at light load), and frequency jittering are included in all package variants for reduced EMI. There are also larger creepage packages, a wider DCMAX, and hysteretic thermal shutdown. Furthermore, all essential parameters (current limit, frequency, and PWM gain) have tighter temperature and absolute tolerances, making design easier and lowering system costs.
These IC functions as a switched-mode power supply chip that converts a current at control input to a duty cycle at the open-drain output of high voltage power MOSFET. During normal functioning of IC, the duty cycle of power MOSFET reduces linearly with increase in CONTROL pin current.
​APPLICATIONS:
- A 35 W, dual output- Universal input power supply with high efficiency
- 150 W, 250-380 VDC Input Power Supply with high efficiency
- 20 W Continuous – 80 W Peak, Universal Input Power Supply with high efficiency
- 65 W- Universal Input Power Supply with high efficiency

Related products
4 Pin RMC Connector
AP Extension pigtail SMA female socket jack to UFL IPX Connector
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
DC 50A 75mV Current Shunt Resistor for Amp Meter Gauge
Dean Connector
- Male plug size: About 13* 7* 19mm
- Female plug size: About 13* 7* 15mm
- Current Rating: 30Amps
- Colour: Red and golden
- Material: Plastic and metal
- Provides a secure connection for battery and motor connections
- Eliminates the possibility of wrong polarity connections
- Used in RC hobby, car, boat, plane, helicopter, LIPO battery, etc.
- Dimension: 9x0.7x2cm
- Weight:20gm
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃

Reviews
There are no reviews yet.