IRFPE40 Power Mosfet Transistor 800V 5.4A
2SK2655 N-Channel Mosfet Transistor 900V 8A
40HMR120 Metal Diode 40A 1200V
82C55 CMOS Programmable Peripheral Interface
- CMOS Programmable Peripheral Interface
- High speed and low power consumption due to 3m silicon gate CMOS technology
- 3 V to 6 V single power supply
- Full static operation
- Programmable 24-bit I/O ports
- Bidirectional bus operation (Port A)
- Bit set/reset function (Port C)
- TTL compatible
- Compatible with 8255A-5
ESP8266 Serial Wifi module Adapter Plate
Double speed measuring module encoder photoelectric pulse output module
- Color: Green + black
- Material: FR4
- Working Voltage: 4.5~5.5V
- Launch Tube Pressure drop: V f=1.6V
- Launch Tube Current: I f<20mA
- Signal Output: A, B two lines
- TT Power Level
- Resolution: 0.01mm
- Measurement Frequency: 100 kHz
- D Type Holes Encoder Diameter: 24mm
- Encoder Resolution: 20 lines
- Speed measuring Sensor configuration: measure line 1 motor speed
IR-08H Infrared Obstacle Avoidance Sensor Module
- Infra-Red IR Emission Receiver IR-08H for Arduino
- Onboard with HS0038B HS38B IR receiver
- Operating Voltage: 3V – 5.5V
- Detection range : 2cm – 40cm
- Output level: Low logic level when an obstacle is detected
- Working current: 20mAh
- Working temperature: -10’C~+50’C
- IO interface: 4 line (-/+/S/EN)
- Output signal: TTL Level
- Adjusting mode: Multi resistance regulation
- Effective angle: 35°
- Size: 4.5 * 1.1cm(approx)
- Easy to assemble and use
- On-board detection indication
- Pin Connection to the board: 4 pins
- A pre-set knob to fine-tune distance range
2 Wires 0.28 inch Digital Voltmeter DC 0-100V Red Light LED Panel Voltage Meter
- Display ON Voltage: 3 V
- Measurable Voltage Range: 0 to 100V
- Current Consumption: 10 mA
- Refresh Speed: 200ms (one time)
- Minimum Input: 3 V
- Highest Input: 30 V
- Accuracy: 0.1 V
- Colour: Red
- Wires: 3
- Operating Temperature: -10 to 60 degree C
- Holes for Mounting: 3 mm
- Very small and lightweight voltmeter module.
- Very handy and easy to use.
- Red LED display.
- Best operates in the working voltage range of 5V to 24V
- Dimension: 13*30*9mm
- Weight: 3gm
L293D MOTOR DRIVER
- Can be used to run two dc motors with the same IC
- Speed and direction control is possible
- Supply voltage: 4.5 V to 7V
- Motor voltage: 4.5 v to 36v
- Maximum peak motor current: 1.2 A
- Maximum continuous motor current: 600 milli ampere
- Screw terminal connectors for easy connection
- Transition time: 300 ns (at 5v and 24v)
- High noise immunity inputs
- Automatic thermal shutdown
- Available in 16 pin DIP, TSSOP, SOIC package
- Dimension: 48*34*14mm
- Weight: 15gm
Blade Propeller for 8520 8.5x20mm
- Length: 8.5″.
- Pitch: 20″.
- Diameter: 55mm
- Centre hole diameter: 0.97mm
- Colour : Black & Red
- suitable for 90mm-150mm DIY Micro Quadcopter Frame Kits
- Suitable for 1mm shaft diameter Coreless motor 7*16mm, 7*20mm, 8.5*20mm
- Suitable for 1mm shaft diameter Carbon Brush motor N20, M20, N30
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
