15uf 250V DC Axial Capacitor
STEPPER MOTOR MINI
Bullet Connector 3.17mm
20N60 Mosfet Transistor Small 600V 20A
Mini 360 STEP DOWN BUCK CONVERTER POWER MODULE
- MPS MP2307DN buck regulator IC
- Design Non-isolated buck
- Rectification: synchronous rectification
- Input voltage: 4.75V-23V
- Output voltage: 1.0V-17V
- Output current Peak: 3A, continuous 1.8A
- Conversion efficiency: 96%
- Switching frequency: 340KHz
- Built-in 160°C thermal shutdown
- Output ripple: 30mV (no load)
- Load regulation: ± 0.5%
- Voltage regulation: ± 2.5%
- Operating temperature: -40 ° C to + 85 ° C
- Dimensions: 17 * 11 * 3.8mm
ACTIVE BUZZER ALARM
- Operating voltage: 3.3V to 5V
- The Transistor driver module uses S8550/9012
- Wire length: 20.5cm
- Easy installation by the fixed bolt hole
- 3 pin TTL cable
- An active buzzer with a concussion internal source is called to be energized
- The program easy to control-SCM high low sound
- When input I/O input is low level, the buzzer sounds
- 28*13.29*11.5mm
XL6009 4A DC to DC BOOST CONVERTER
- Module Properties: Non-isolated boost (BOOST)
- Rectification: Non-Synchronous Rectification
- Input Voltage Range: 3V ~ 32V
- Output Voltage Range: 5V ~ 35V
- Input Current: 4A (max), no-load 18mA
- Conversion efficiency: <94%
- Switching frequency: 400KHz
- Output Ripple: 50mV (the higher the voltage, the greater the current, the greater the ripple)
- Load Regulation: ± 0.5%
- Voltage Regulation: ± 0.5%
- Operating Temperature: -40degree ~ +85 degree
- Dimensions: 43mm * 21mm * 14mm
3.17mm RC Aluminum Bullet Propeller Adapter Holder
- Bore Diameter: 3.7mm (expandable up to 4.1mm).
- Material: Aluminium.
- Colour: Silver.
- Ease of interfacing.
- Rust-free and stain-free aluminum metal construction.
- Used to capture propeller with BLDC motor in quad-copter/multi-rotor/drone.
- High-quality aluminum material.
- Suitable for brushless motors and speed controllers.
- Delicate workmanship.
- High-Quality RC 3.17mm Prop Adaptor For Motor Propeller Plane, Multicopter, Quadcopter
- Dimension: 2.5mm Long x 12mm Diameter
- weight: 4g
6045(6×4.5) Propeller
- Length: 6″.
- Pitch: 4.5″.
- Shaft Diameter: 5mm.
- Total length: 6 inch / 150 mm.
- Material: Glass Fiber Nylon
- It includes a set of plastic reducers(3, 4, 5, 6 mm)
- Durable plastic construction provides both lightness and rigidity.
- Â 6045(6X4.5) Glass Fiber Nylon Propeller comes Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
Red TTP223 Touch button Module
- Input Voltage: 2 Volt - 5.5 Volts DC.
- Current Consumption: < 7 µA
- Low Power Mode and Fast Mode
- Start-up Calibration Delay: 0.5 Sec
- Simple, easy to use, with Auto Calibration
- Output mode is set by Jumper
- The response time max is ~ 60mS in fast mode, ~220mS at low power mode @VDD=3V.
- Sensitivity can adjust by the capacitance (0~50pF).
- Supports momentary or latching/toggle modes.
- Have two kinds of sampling length by pad option (SLRFTB pin)
- Provides Fast mode and Low Power mode selection by pad option (LPMB pin).
- Provides direct mode toggle mode by pad option (TOG pin).
- All output modes can be selected as active high or active low by pad option (AHLB pin).
- Have the maximum on-time 100sec by pad option (MOTB pin).
- Have external power-on reset pin (RST pin).
- Auto-calibration &Re-calibration period is about 4.0 sec when the key has not to be touched.
- Dimensions: 15mm x 11mm.
TTP223 1way
- Power supply for 2 ~ 5.5V DC
- Output high VOH: 0.8VCC V
- Output low VOL: 0.3VCC V
- Response time (touch mode) : 60 mS
- Output Pin Sink Current (@ VCC = 3V, VOL = 0.6V) : 8 mA
- Output pin pull-up current (@ VCC = 3V, VOH = 2.4V) : 4 mA
- Response time (low power mode) : 220 mS
- Low power consumption
- Can replace the traditional touch of a button
- Four M2 screws positioning holes for easy installation
- Size : 24 x 24 x 7.2 mm
