Mh13001 220V Digital Air Humidity Control Controller Range 1% – 99%
- Model Name: MH 13001
- Voltage: 220 Volt
- Accuracy: +-3% RH
- Type: Digital
- Color: Black
- Display Type: LCD
- Input Sensor: Humidity Sensor
- Humidity: 1% ~ 99% RH\humidity measuring
- Error: ±3 percent rh
- Control range: 1 percent RH
- Power consumption:3w
- Output load: Ac 10a/220v
- Working temperature: 0°c - 80 °c
- Dimensions: 8 x 5 x 3cms
- Usage/Application: Air Humidity Controller Hygrostat Humidistat Humidification Dehumidification
GSM GPRS + Camera Module A6C Breakout
- Operating Voltage: 3.3V – 4.2V
- Working Temperature: -30 ℃ to +80℃
- Boot Voltage: >3.4V
- Standby Current: less than 3 mA
- GSM/GPRS Frequency Band: including 850, 900, 1800, 1900 MHZ
- GPRS Class 10
- Sensibility: <-105
- Voice Call: Support
- SMS message: Support
- GPRS maximum speed: Download speed 85.6Kbps, Upload speed 42.8Kbps
- AT Command: Support standard GSM07.07, 07.05, and extended Ai Thinker command
- 2 UART: one for download, one for AT command
- Audio: Support digital and analog audio, support HR, FR, EFR, AMR audio code
- Camera resolution: 0.3M
Arduino Mega 2560 Board
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 128 KB of which 4 KB used by the boot loader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
TDA7498E Double 160W Power Amplifier Dual Channel Stereo Audio Amplifier Module Support BTL Mode
- Amplifier chip: TDA7498E
- Working voltage: DC 15-36V (Recommend 32V, 8A, if power is too small will appear distortion and so on.)
- Output power: 2 x 160W
- Number of channels: Two-channel Stereo
- Efficiency: 85%
- Applicable speaker impedance: 4/6/8ohm (8ohm is the best).
- 160-W + 160-W output power at THD = 10% with RL = 4 Ω and VCC = 36 V
- 1 x 220 W output power mono parallel BTL at THD = 10% with RL = 3 Ω and VCC = 36 V
- Wide-range single-supply operation (14 - 36 V)
- High efficiency (η = 85%)
- Parallel BTL function using the MODE pin
- Four selectable, fixed gain settings of nominally 23.8 dB, 29.8 dB, 33.3 dB and 35.8 dB
- Differential inputs minimize common-mode noise
- Standby and mute features
- Smart protection
- Thermal overload protection
- Small offset less than 20 mV
- PCB board size: 108 x 78mm
- Weight: 172g(approx.)
FlexiForce Tekscan A201 Sensor
- Thickness 0.203 mm (0.008 in.)
- Length 191 mm (7.5 in.)** (optional trimmed lengths:
- 152 mm (6 in.), 102 mm (4 in.), 51 mm (2 in.))
- Width 14 mm (0.55 in.)
- Sensing Area 9.53 mm (0.375 in.) diameter
- Connector 3-pin Male Square Pin (centre pin is inactive)
- Substrate Polyester
- Pin Spacing 2.54 mm (0.1 in)
- Small size is ideal for prototyping and integration
- Thin and flexible
- Easy to use
Ublox NEO-M8N GPS Module with Compass for APM with extra connector for Pixhawk
- Ready to Connect to All APM FC with 5-pin connector Attached
- Receiver type 72-channel M8 engine
- Galileo-ready E1B/C (NEO-M8N)
- update rate1 Single GNSS: up to 18 HZ
- Position accuracy 22.0 m CEP
- Acquisition2 Cold starts: 26 s
- Sensitivity2 Tracking & Nav: –167 dBm
- On-board Compass
- Dimensions: Outer diameter 54mm
- GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1.
- SBAS L1 C/A: WAAS, EGNOS, MSAS.
- Assistance AssistNow GNSS Online.
- Assist Now GNSS Offline (up to 35 days)3.
- Assist Now Autonomous (up to 6 days).
- OMA SUPL & 3GPP compliant
- Oscillator TCXO (NEO-M8N/Q).
- Crystal (NEO-M8M).
- RTC crystal Built-In.
- Noise figure On-chip LNA (NEO-M8M). Extra LNA for.
- Lowest noise figure (NEO-M8N/Q).
- Anti-jamming Active CW detection and removal.
- Extra onboard SAW bandpass filter (NEO-M8N/Q).
- Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N).
- Supported antennas Active and passive.
- Odometer Travelled distance.
- Data-logger For position, velocity, and time (NEO-M8N).
- Weight 33gm
“PWM Generator Module for Stepper Motor Driver with Forward and Reverse Function “
- Board can be used to generate PWM signals for the stepper motor driver
- Operating Voltage: 12VDC
- Three Frequency Range
- Forward and Reverse Function.
- It has three frequency ranges selectable via onboard jumpers.
- Frequency can be measured via PUL and common cathode (GND) ports.
- The board has two sets of power input
