Showing 13–24 of 24 results

ATtiny85 Arduino-enabled Mini USB Dev Board

₹200.00
  • Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
  • Power via USB or External Source
  • Onboard 5V Regulator
  • Built-in USB
  • 6 I/O Pins
  • 8k Flash Memory (about 6k after bootloader)
  • I2C and SPI (vis USI)
  • PWM on 3 pins (more possible with Software PWM)
  • 10-bit ADC
  • ADC on 4 pins
  • Power LED and Test/Status LED
  • Low Power Consumption
  • Active Mode:1 MHz, 1.8V: 300 µA

LilyTiny (LilyPad ATTiny85)

₹425.00
  • Program Memory Type: Flash
  • Program Memory (KB) : 8
  • CPU Speed (MIPS): 20
  • Data EEPROM (bytes): 512
  • Digital Communication Peripherals: 1-SPI, 1-I2C
  • Capture/Compare/PWM Peripherals : 5
  • Comparators: 1
  • Temperature Range (C) : -40 to 85
  • Operating Voltage Range (V): 1.8 to 5.5
  • Pin count: 8
  • Cap Touch Channels : 3

Pro Micro 5V 16M Mini Microcontroller Development Board For Arduino

₹800.00 inc. GST
  • ATMEGA32U4 chip
  • Supply Voltage: 5VDC
  • Frequency: 16Mhz
  • Support Arduino IDE V1.0.1
  • Four 10 bit ADC pins
  • 12 pins Digital I/O(5 PWM capability)
  • Micro USB interface programming on the board
  • Rx and Tx hardware serial connection
  • Dimension: 33mm x 18mm

UNO R3 +WiFi ATmega328P+ESP8266 Module CH340G Compatible For Arduino Uno

₹1,300.00 inc. GST
  • Microcontroller: ATmega328IC
  • Wi-Fi: ESP8266
  • USB-TTL converter: CH340G
  • Power Output: 5V-800mA
  • Power input USB: 5V (500mA max.)
  • Power input VIN/DC Jack: 9-24V
  • Power Consumption: 5V 800mA
  • Logic Level: 5V
  • WiFi: 802.11 b/g/n 2.4 GHz
  • USB type: Micro USB
  • USB Clock Frequency: 16MHz
  • Operating Supply Voltage: 5V
  • Digital I/O Pins: 14
  • Analog I/O pins: 6
  • Memory Size: 32Mb
  • Interface Type: serial
  • Operating temperature: −40С°/+125С°
  • Dimensions (L×W)mm: 53.34×68.58

Aluminum Heatsink Cooler Cooling Kit for Raspberry Pi 3/2 Model 3B+ – 3 Piece

₹80.00 inc. GST
  • 3m - Sticker for best adhesiveness to the silicon.
  • Best aluminium - ensures best fin efficiency and fin effectiveness.
  • Colour: Black.
  • Suitable for raspberry pi models a, b, b+, 2, and 3 boards.
  • Can be applied with other devices such as the beaglebone.
  • Dimensions:
-  Large Heatsink: 14 x 14 x 6  mm -    Small Heatsink: 9 x 9 x 5  mm
  • Teeth Number:
-    Large Heatsink: 7 Teeth -Small Heatsink: 5 Teeth
  • Compatible with most Raspberry Pi cases
  • Compatible with other devices such as the Beaglebone
  • Compatible with stepper motors, motor driver boards, etc.

AVR-ISP 10Pin to 6pin Adapter PCB for USBASP Programmer

₹470.00 inc. GST
  • Made of high-quality material, practical and durable
  • Number of Pinon USBASP side: 10.
  • A number of Pinon Device under the programming side: 6.
  • Connector type on USBASP side: Male.
  • Connector type on Device under programming side: Female.
  • Header Pin Pitch: 2.54mm (0.1in).

ESP8266 ESP – 07

₹299.00 inc. GST
  • Smallest 802.11b/g/n Wi-Fi SOC module
  • Low power 32-bit CPU, can also serve as the application processor
  • Up to 160MHz clock speed
  • Built-in 10 bit high precision ADC
  • Supports UART/GPIO/IIC/PWM/ADC
  • SMD-16 package for easy welding
  • Integrated Wi-Fi MAC/BB/RF/PA/LNA
  • Deep sleep current as low as 20uA
  • Embedded LWIP protocol stack
  • Supports STA/AP/STA + AP operation mode
  • Support Smart Config/AirKiss technology
  • UART baudrate up to 4Mbps
  • General AT commands can be used quickly
  • Supports remote firmware upgrade (FOTA)
  • WIFI Direct (P2P),SOFT-AP
  • Built-in TCP/IP
  • The AT command is perfect, efficient, concise
  • Support three modes: AP, STA and AP+STA coexistence mode
  • Onboard Chip Antenna
  • +19.5dBm output power in 802.11b mode
  • Power down leakage current of <10uA
  • SDIO 1.1/2.0, SPI, UART
  • STBC, 1×1 MIMO, 2×1 MIMO
  • A-MPDU & A-MSDU aggregation & 0.4ms guard interval
  • Wake up and transmit packets in < 2ms
  • Standby power consumption of < 1.0mW (DTIM3)

ESP8266 ESP – 03 WIFI Transreceiver Wireless Module

₹800.00 inc. GST
  • Communication interface voltage: 3.3V
  • Working current: 240mA(MAX)
  • 802.11 b/g/n
  • Wi-Fi Direct (P2P), soft-AP
  • Integrated TCP/IP protocol stack
  • Integrated TR switch, balun, LNA, power amplifier and matching network
  • Integrated PLLs, regulators, DCXO and power management units
  • +19.5dBm output power in 802.11b mode
  • Power down leakage current of <10uA
  • Integrated low power 32-bit CPU could be used as application processor
  • SDIO 1.1/2.0, SPI, UART
  • STBC, 1×1 MIMO, 2×1 MIMO
  • A-MPDU & A-MSDU aggregation & 0.4ms guard interval
  • Wake up and transmit packets in < 2ms
  • Standby power consumption of < 1.0mW (DTIM3)
  • SDIO 2.0, SPI, UART
  • 32-pin QFN package
  • Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
  • Integrated RISC processor, on-chip memory and external memory interfaces
  • Integrated MAC/baseband processors
  • Quality of Service management
  • I2S interface for high fidelity audio applications
  • On-chip low-dropout linear regulators for all internal supplies
  • Proprietary spurious-free clock generation architecture
  • Integrated WEP, TKIP, AES, and WAPI engines

ESP8266 ESP-12F

₹200.00 inc. GST
  • Communication interface voltage: 3.3V
  • Working current: 240mA(MAX)
  • Serial port baud rate: 115200 (default), can be modified to other values by AT command
  • Serial communication format: 8N1
  • Wireless Network Mode: station / softAP / SoftAP + station
  • Wireless criteria: 802.11 b / g / n
  • WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
  • +19.5dBm output power
  • Compatible with ESP-12(ESP-202)
  • It is very easy to develop projects with AT commands
  • Surface Mount Package with 2mm Pitch Pads
  • Mulitple GPIO’s for all your sensor needs
  • Integrated TCP/IP protocol stac
  • Integrated TR switch, balun, LNA, power amplifier and matching network
  • Integrated PLL, regulators, DCXO and power management unit
  • Power down leakage current of <10uA
  • Integrated low power 32-bit CPU could be used as an application processor
  • SDIO 1.1/2.0, SPI, UART
  • STBC, 1×1 MIMO, 2×1 MIMO
  • A-MPDU & A-MSDU aggregation & 0.4ms guard interval
  • Wake up and transmit packets in < 2ms
  • Standby power consumption of < 1.0mW (DTIM3)
  • Both SMD and Inline package are available, and the pin pitch is 2.0mm.

Evaluation Board For Pi

₹1,700.00 inc. GST
  • Designed for Raspberry Pi
  • UART interface: easily connects to UART modules such as RS232, RS485, USB TO UART, etc.
  • 8 I/Os interface: easily connects to modules controlled by I/Os, such as 8 Push Buttons, Logic Level Converter, Mix Board, etc.
  • SPI interface: easily connects to SPI modules such as AT45DBXX Data flash, L3G4200D Board, etc.
  • I2C interface: easily connects to I2C modules such as PCF8574 Expansion Board, PCF8563 RTC Board, LSM303DLHC Board, etc.
  • Character LCD interface: for connecting character LCDs like LCD1602
  • USB connector: USB TO UART, supported by onboard converter CP2102
  • Power indicator, User LEDs, User Keys
  • Potentiometer: for LCD1602 contrast adjustment
  • PCF8563 onboard RTC chip with battery holder and crystal

7” Touch Screen

₹7,000.00 inc. GST
  • 800×480 high resolution.
  • Viewable screen size: 155mm x 86mm
  • 10 finger capacitive touch
  • Supports Raspberry Pi, and the driver is provided (works with custom Raspbian directly).
  • Supports BB Black, comes with related images like Angstrom.
  • Supports Banana Pi / Banana Pro, which comes with related images like Ubuntu, Raspbian.
  • Connects to the Raspberry Pi board using a ribbon cable connected to the DSI port.
  • The Adapter board is used to power the display and convert the parallel signals from the display to the serial (DSI) port on the Raspberry Pi.
  • Require the latest version of Raspbian OS to operate correctly
  • Not only for mini-PCs, but it can also work as a computer monitor just like any other general HDMI screen (touch function is unavailable in this case).
  • HDMI interface for displaying, USB interface for touch control.
  • Back light control to lower power consumption.
  • Screen Dimensions: 194mm x 110mm x 20mm

USBASP PROGRAMMER

₹399.00 inc. GST
  • No special USB controller required
  • Programming speed is up to 5Kbytes/sec
  • Working platform: Linux, Windows, Mac OS X
  • Allows to read or write the microcontroller EEPROM, firmware, fuse bits, and lock bits
  • No special controllers or SMD components are needed.
  • Target is supported by the SCK option with a low clock speed (<1.5MHz)
  • Programming status and Bus status are easily identified
  • The easy interface is achieved by Header pins for various ISP header pins
  • Dimension: 63.3*20.5*10.5mm
  • Weight: 15gm