Showing 1–12 of 25 results

16×2 (1602) LCD Keypad Shield

₹400.00 inc. GST
  • Operating Voltage:5V
  • 5 Push buttons.
  • RST button to reset Arduino program.
  • Integrate a potentiometer for adjusting the backlight.
  • Expanded available I/O pins.
  • Blue light with white characters.
  • Uses 4 Bit Arduino LCD Library
  • Screen contrast adjustment
  • Arduino Reset button
  • The keypad consists of 6 keys select, up, right, down, left and reset.
  • To save the digital IO pins, the keypad interface only uses one ADC channel.
  • The key value is read out through a 5 stage voltage divider.

2.4″ Inch Touch Screen TFT Display Shield for Arduino

₹800.00 inc. GST
  • 4″ Touch LCD TFT display module for Arduino
  • 240*320 pixels resolution
  • Ability to display 262000 different colours
  • The shield comes equipped with a microSD card slot.
  • SPFD5408 controller with built-in video RAM buffer
  • 8-bit digital interface, plus 4 control lines
  • 5V compatible. Use with 3.3V or 5V logic
  • On-board 3.3V 300mA LDO regulator
  • Uses digital pins 5-13 and analogue 0-3. That means you can use digital pins 2, 3, and analog 4 and 5. Pin 12 is available if not using the microSD
  • Works with any Arduino Uno and mega compatible boards
  • Resolution: 240320 pixels
  • Supply voltage: 5V
  • Working temperature: -30C ~ 70C
  • Dimension: 72*52*12mm

Arduino Compatible Nokia 5110 Prototype Proto Shield Expansion Board

₹550.00 inc. GST
  • Supports Nokia5110 display
  • Standard 0.1"x0.1" prototyping grid with big pads
  • Comes with Stacking headers and plain header, choose whichever you want when soldering together
  •  IC pattern for adding DIP ICs up to 20 pins
  • Power rails down the middle and sides
  • Reset button and an extra general use button
  • 2 3mm general use LEDs, red and green, as well as 2 matching resistors
  • A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
  • Surface-mount chip area for up to 14 SOIC size parts
  • Compatible with tiny breadboards
  • Every pin is brought out
  • Gold plated pads
  • 2 x 0.1uF capacitors on either side for extra power stability

ATtiny85 Arduino-enabled Mini USB Dev Board

₹200.00
  • Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
  • Power via USB or External Source
  • Onboard 5V Regulator
  • Built-in USB
  • 6 I/O Pins
  • 8k Flash Memory (about 6k after bootloader)
  • I2C and SPI (vis USI)
  • PWM on 3 pins (more possible with Software PWM)
  • 10-bit ADC
  • ADC on 4 pins
  • Power LED and Test/Status LED
  • Low Power Consumption
  • Active Mode:1 MHz, 1.8V: 300 µA

Bluetooth Relay Shield

₹1,300.00 inc. GST
  • Supply Voltage: 5V
  • Max Relay current: 5 Amps
  • Potential free contacts
  • Bluetooth Wireless Interface
  • 200 to 300 Ft. Wireless Range
  • Mounts as a Virtual COM Port on PC/Laptop
  • Pair with Smartphone or Tablet

CAN Bus Shield

₹1,500.00 inc. GST
  • Implements CAN V2.0B at up to 1 Mb/s
  • Industrial standard 9 pin sub-D connector
  • OBD-II and CAN standard pinout selectable.
  • Changeable chip select pin
  • Changeable CS pin for TF card slot
  • Changeable INT pin
  • Screw terminal that easily to connect CAN_H and CAN_L
  • Arduino Uno pin headers
  • Grove connectors (I2C and UART)
  • SPI Interface up to 10 MHz
  • Standard (11 bit) and extended (29 bit) data and remote frames
  • Two receive buffers with prioritized message storage
   

DTMF Shield

₹800.00 inc. GST
  • MT8870 Decoder IC.
  • 4 Output digital pins.
  • Operates on 5V
  • Includes MT8870 DTMF Receiver IC
  • Receives and Converts Standard DTMF Codes
  • Remotely Switch Devices from Anywhere Using the Phone
  • Easily Connects to Most Microcontrollers or Roboduino Board
  • Low Power Consumption
  • 5 On-Board LED's For Data Received Indication
  • Standard Header Connections for Control System Connection
  • Audio socket for application
  • Speaker connector for audio sound checking.
  • Microphone connector for over the air remote control system( note, due to environmental noise, without any filtering system this method is not recommended)
  • Dimension: 37x37x9mm

Dual Monster Moto Shield VNH2SP30 Motor Driver 2x14A (Peak 30A)

₹899.00 inc. GST
  • Driver Model: VNH3ASP30
  • Current sensing available to Arduino analogue pin
  • Operating Voltage: 12 V to 16V DC
  • Peak Current: 14A
  • Continuous Current: 30A
  • of Channels: 2
  • Maximum PWM frequency: 20 kHz
  • MOSFET on-resistance: 19 m (per leg)
  • Thermal Shutdown protection
  • Under-voltage and Overvoltage shutdown.
  • LED Indicator
  • Dimensions: 60 x 54 x 12mm
  • Weight: 19gm

ESP8266 WIFI Shield

₹899.00 inc. GST
  • Operating voltage 5V (supplied from the Arduino Board)
  • Connection via: 802.11b/g networks
  • Encryption types: WEP and WPA2 Personal
  • Connection with Arduino on SPI port
  • on-board micro SD slot
  • ICSP headers
  • FTDI connection for serial debugging of WiFi shield
  • Mini-USB for updating WiFi shield firmware
  • 32-bit RISC architecture
  • The processor can operate at 80MHz / 160MHz
  • 32MB flash memory
  • 64kB for instructions
  • 96kB for data
  • Operates in AP, Station or AP + Station mode
  • It has 11 digital pins
  • It has 1 analogue pin with 10-bit resolution
  • Digital pins except the D0 have interrupts, PWM, I2C and one wire
  • Programmable through USB or WiFi (OTA)
  • Compatible with Arduino IDE
  • Compatible with modules and sensors used in Arduino

Ethernet Shield

₹750.00 inc. GST
  • Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
  • Stackable Design, can directly be supported by Arduino official Ethernet Library.
  • Supports up to four simultaneous socket connections
  • Can be used to store files for serving over the network.
  • Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
  • Can be accessed using the Mini SD TF library.
  • The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
  • IEEE802.3af compliant
  • Low output ripple and noise (100mVpp)
  • Overload and short-circuit protection
  • 1500V isolation (input to output)

HC-05 Bluetooth Shield for Arduino

₹799.00 inc. GST
  • Bluetooth serial port Profile
  • Bluetooth protocol: Bluetooth Specification v2.0+EDR
  • Frequency: 2.4GHz ISM band
  • Communication Range: 10M
  • Serial Bluetooth module for Arduino
  • Can operate in Master, Slave or Master/Slave mode
  • UART interface (TTL) with programmable baud rate (SPP firmware installed)
  • Default baud rate: 38400(CMD MODE) / 9600(DATA MODE), data bits: 8, stop bit: 1, Parity: No parity
  • Onboard PCB antenna
  • FCC ID certificated

Joystick Shield

₹400.00 inc. GST
  • NRF24L01 RF interface.
  • For Nokia 5110 LCD interface.
  • Bluetooth interface I2C interface.
  • For one PS2 joystick.
  • 2-Axis joystick.
  • Bluetooth / Serial interface.
  • I2C interface.
  • nRF24L01 interface.
  • Nokia 5110 LCD interface.
  • Interface connector.
  • Power switch to switch between 3.3 and 5V