36O DEGREE ROTATIONAL ENCODER
GPS Ublox Neo 6M TTL
- Supply voltage: 3.3 V
- 5Hz position update rate
- Operating temperature range: -40 TO 85°C
- UART TTL socket
- EEPROM to save configuration settings
- Rechargeable battery for Backup
- The cold start time of 38 s and Hot start time of 1 s
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600)
- -162 dBm tracking sensitivity
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
- Separated 18X18mm GPS antenna
12V Wireless Power Supply Module Wireless Charging Module Wireless Transmission Module
- Magnetic-Coupled Resonance Technology
- Transmitting Voltage: 12V
- Output Power: 36W
- Output Voltage & Current: 12V, 3A
- Coil Size: outer diameter 82mm; inner diameter 30mm
- Transmitting Module Size: 17mm*30mm
- Receiving Module Size: 30mm*54mm
- Insulation Coil
- Compact Design
- Stable power supply
- Insulation Coil
- Space-saving design
SIM800L GPRS GSM Module
- Chip: SIM800L
- Operating voltage: 3.7V -4.2V
- Current : 2A
- Quad-band (850/900/1800/1900MHz) supports
- Searches for network and login automatically
- Can connect any global GSM network with 2G sim
- Miniature size
- AT command interface with auto baud detection
- Lead-out buzzer and vibration motor control port
- Scan and receive FM radio broadcast, send and receive SMS and call
- Power consumption:
- Interface: UART (max 2.8V, serial interface)
- Command support: 3G PP TS 27. 007, 27. 005 and SIMCOM enhanced AT commands
- Sim Card Slot: Micro SIM
- Temperature range: -40℃ to 85℃
PIR Sensor
- Wide Working Voltage Range: DC 4.5V- 20V
- Current Drain: <60uA
- Detection Angle: <140°
- Detection Distance: 3 to 7m (can be adjusted)
- Blockade time: 2.5s (Default)
- Work temperature: -20-+80°C
- Colour: White + Green OR White + Blue
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time Can be Adjusted
- Voltage Output: High/Low level Signal: 3.3V TTL output
- Delay Time: 5 to 200s (Can be Adjusted, Default 5s +/- 3%)
- Blockade time: 2.5s (Default)
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
- Dimension: 3.2cm x 2.4cm x 1.8cm
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
LoRa SX1278 433M 10KM Wireless Spread Spectrum Transmission Module Ra-02 SX1278 Socket IOT
- Lora Spread Spectrum Modulation Technology +20dBm-100mW
- Constant RF power output when voltage changes
- High sensitivity: low to -148dBm
- Half-duplex SPI communication Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
- 127dB RSSI dynamic range
- Automatic RF signal detection
- CAD model and ultra-high-speed AFC With CRC, up to 256 bytes of the packet engine
- Small volume dual-row stamp-hole patch package
- With shielding shell Spring antenna (Ra-01) external antenna (Ra-02)
- Wireless standard 433MHz Frequency range: 420 ~ 450MHz
- Interface: SPI GPIO
- Operating Voltage:1.8 ~ 3.7V, the typical value is 3.3V
- Current: Receiver:≦ 10.8mA (LnaBoost off, band 1) Transimit: ≦ 120mA (+ 20dBm)
- Sleep mode: 0.2μA
- Working temperature: -40 to + 85 ° C
- Storage temperature: Normal
Load Cell CZL 601 80KG
- Type: Single Point Load Cell
- Total Precision: C3 class
- Material: Aluminum Alloy
- Surface: Anodized Treatment
- Protection: IP65
- Rated Load: 80 Kg. Max
- Rated Output : 2.0 mV/V+/- 5%
- Zero Balance : +/- 1% Full Scale
- Excitation Voltage: 9-12 Volt DC
- Nonlinearity : 0.017% Full Scale
- Hysteresis: 0.02% Full Scale
- Repeatability : 0.01% Full Scale
- Creep(30min) : 0.015% Full Scale
- Operating Temperature : -20 °C to +65 °C
- Safe Overload: 120% of Rated Capacity
- Ultimate Overload: 150% of Rated Capacity
- Cable: 420mm (3mm dia 4 wire shielding cable)
Ultrasonic Module HC-SR-04
- Sensor Type: Ultrasonic
- Output: Digital Sensor
- Voltage: 5VDC
- Operating Current: 15mA
- Measure Angle: 15°
- Ranging Distance: 2cm - 4m
- Static current: < 2mA
- Level output: high-5V
- Output Signal:5V
- High Precision: Up to 2 mm
- Input Trigger Signal: 10µs TTL impulse
- Echo Signal: Output TTL PWL Signal
- High sensitivity ultrasonic range sensor
- Works with Arduino board
LDR Module
- Operating Voltage:3V to 5V DC
- Operating Current: 15milli amps
- LED indicating output and power
- LM393 comparator chip
- Can detect ambient brightness and light intensity.
- Output Type :Â - Digital switching outputs (0 and 1) -D0
- Output Digital: 0V to 5V, Adjustable trigger level from preset
- Power indicator (red) and the digital switch output indicator (green)
- It can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- Fixed bolt hole for easy installation
- PCB size: 3cm * 1.6cm
MPU6050 6AXIS (GYROSCOPE + ACCELEROMETER) SENSOR
- MEMS 3-axis accelerometer and 3-axis gyroscope values combined
- Power Supply: 3-5V
- Communication: I2C protocol
- Built-in 16-bit ADC provides high accuracy
- Sensing range: +/-2G to +/-16G
- Built-in DMP provides high computational power
- Can be used to interface with other IIC devices like a magnetometer
- Configurable IIC Address
- In-built temperature sensor
- Ideal for noisy power environment
- Operating temperature: -40 degrees to 85 degrees Celsius
- Dimension: 28*14mm
DS1307 RTC MODULE
- DS1307 I2C real-time clock chip (RTC)
- Available in 8-pin DIP or SOIC
- Accessed via I2C protocol
- AT24C32 32K I2C EEPROM memory
- Bidirectional I2C interface.
- Hour:Minutes: Seconds AM/PM.
- Day Month, Date - Year.
- DS1307 based RTC with LIR2032 battery.
- 1Hz output pin.
- 56-byte non-volatile RAM for data storage
- 56 Bytes of Non-volatile memory for user
- The DS1307 is accessed via the I2C protocol.
- Consumes less than 500nA in battery backup mode with oscillator running
- Dimension: 27mm * 28mm * 8.4mm
SOUND SENSOR
- IC Chip: LM393
- Operating voltage: 3.3V-5V
- operating current: 4-5 mA
- Voltage gain 26 dB (v=6v, f=1khz)
- Sensitivity of the microphone (1khz) :52 to 48 dB
- The impedance of the microphone: 2.2k ohm
- Frequency of microphone: 16 to 20 kHz
- Signal to noise ratio: 54 dB
- Signal output indication
- The output is digital.
- Single-channel signal output.
- With the retaining bolt hole, convenient installation.
- Output low level and the signal light when there is sound.
- Dimension:45*17*9mm
- Weight: 5gm
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
HC-12 433 SI4463 Wireless Serial Module
- IEEE 802.15.4g compliant
- Supply voltage: 3.2V~5.5V
- Operating frequency range: 433.4-473.0MHz,
- Up to 100 channels of communication
- Receive sensitivity = –126 dBm
- Serial TTL (RX, TX, GND) interface
- Modulation (G)FSK, 4(G)FSK, (G)MSK, OOK
- Maximum transmit power: 100mW (settable)
- Max output power: +20 dBm
- Low active power consumption: 10/13 mA RX, 18 mA TX at +10 dBm
- Ultra-low current power-down modes: 30 nA shutdown, 50 nA standby
- Data rate: 100 kbps to 1 Mbps
- Fast wake and hop times
- The highly configurable packet handler
- TX and RX 64 byte FIFOs
- Auto frequency control (AFC)
- Automatic gain control (AGC)
- Low BOM and battery detector
- Default factory settings: Mode FU3, the baud rate is 9600bps, communication channels CH001 (433.4M)
MQ135 Module
- Working voltage: DC 5V
- Working Current: 150mA
- DOUT: TTL output
- AOUT: Analog output
- Preheat time: Over 20s
- Detection Range: 10 - 300 ppm NH3, 10 - 1000 ppm Benzene, 10 - 300 Alcohol
- Sensitivity to Ammonia, Sulphide, and Benzene steam
- With signal output instructions
- The TTL output signal is a low level
- Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
- Sensitive for benzene, alcohol, smoke
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Dimension: 32mm x 22m x 27mm
4 Channel 5V Relay Module Shield For Arduino
- Product Type: 4-Channel relay module
- Dimensions: 75 mm x 55 mm x 19.3 mm
- Weight: 61 g
- Relay colour: Blue
- PCB colour: Blue
- Maximum output of relay: AC250V 10A and Dc30V 10A
- Number of Relays: 4
- Control signal type: TTL level
- Input voltage: 5v
- Compatible with: Arduino, AVR, PIC, ARM, Raspberry Pi etc
- Package contains: 1 piece of 4 channel relay module
Zigbee CC2500 RS232
- RS-232 direct interface
- TTL support
- RSSI value between two modules can be obtained
- Separate LED for RX, TX, and power
- 4-bit channel selection
- Programmable output power
- Automatic packet processing
- 6 data pipes for 1:6 star networks
- 4-pin SPI interface with maximum 8 MHz clock rate 7
- 20-pin 4x4mm QFN package
pH Sensor Module & pH electrode Probe for Arduino, AVR, PIC
- Module Power: DC 5.00V.
- Measuring Range: 0-14PH.
- Accuracy: 0.01 pH
- Response Time: ≤ 1min.
- Industry pH Electrode with BNC Connector.
- Power Indicator LED.
- Output: Analog values in the range of (0.5V to 3V).
- Alkali Error: 0.2PH.
- Internal Resistance: 250MOhm.
- Gain adjustment Potentiometer.
- Measuring Temperature: 0 degrees to 50 degrees C
- Terminal Blocks: BNC plug.
- BNC Connector is suitable for most pH meters and controllers.
- Suitable for a wide range of applications: Aquariums, Hydroponics, Laboratory etc.
- Module Size: 50 x 47 x 16mm
Color Sensor
- Voltage supply: 2.7V to 5.5V
- Colour sensor IC: TSC3200
- Interface: digital TTL
- Single-Supply Operation (2.7V to 5.5V)
- High-Resolution Conversion of Light Intensity to Frequency
- Programmable Color and Full-Scale Output Frequency
- Power Down Feature
- Programmable colour and full-scale output frequency.
- Easy to interface with microcontrollers like AVR, ARM, PIC, Arduino etc
- S0~S1: Output frequency scaling selection inputs
- S2~S3: Photodiode type selection inputs
- OUT Pin: Output frequency
- OE Pin: Output frequency enable pin (active low), can be impending when using
- Support LED lamp light supplement control
- Working temperature range: -40℃ to +80℃
DHT11 MODULE
- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0°C to 50°C
- Humidity Range: 20% to 90%
- Resolution: Temperature and Humidity both are 16-bit
- Accuracy: ±1°C and ±1%
- Low power consumption.
- The module can detect the surrounding environment of the humidity and temperature
- High reliability and excellent long-term stability
- The output from the digital output
- Has fixed bolt hole and easy installation
HC-06 4Pin Bluetooth Module Without Reset Switch
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Dormancy current: no dormancy.
- Used for a GPS navigation system, water, and electricity gas meter reading system.
- With the computer and Bluetooth adapter, PDA, seamless connection equipment.
- Bluetooth module HC-08 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
AMS1117 3.3V POWER SUPPLY MODULE
• Input: DC 4.5V – 12V (input voltage must be more than the output voltage (more than 1V))
• Output: 3.3V, 800mA (load current cannot exceed 800mA)
• Onboard AMS1117 chip.
• Onboard power indicator to indicate power is turned on: Red LED.
• Output voltage interface, connection to facilitate the experimental.
• Specially designed two pin mounting holes, can be directly fixed on the whole expansion board for experiments.
• Small Compact Size, 4Pin Type, Breadboard Friendly.
• 2P single row pin input and output for easy connection
• Dual-panel design, the layout is nice
MQ-9 Carbon Monoxide, Methane and LPG Gas Sensor Module
- Input voltage: DC 5V
- Power: 150mA
- DO output: TTL digital 0 and 1 (0.1 and 5V)
- AO output: 0.1-0.3V (relatively clean), the highest concentration voltage is about 4V.
- Suitable for home or factory gas leakage monitoring devices.
- Have better sensitivity to Carbon Monoxide, Methane and LPG Gas.
- High quality dual-panel design, with power indicator and TTL signal output instructions.
- DO switching signal (TTL) output and AO analog signal output.
- TTL output valid signal is low. (When the output low signal is on, it can be directly connected micro-controller or relay module.)
- Analog output voltage: the higher concentration, the higher voltage.
- Four screw holes, easy positioning.
- Long life and stability, quick response and resume.
TM1637 4 Bits Digital Tube LED Display Module With Clock Display for Arduino
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 30 mA
- Display Dimensions: 42x24x12 (LxWxH) mm
- Ease to use.
- Ease of multiplexing.
- Can use as a 4 digit display unit.
- Can use as a clock display.
- The counter project uses 7 segment display.
- 4 M2 screws positioning holes for easy installation
IR Proximity Module using TSOP
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
RFID EM18 125KHz RS232 Output
- Operating Voltage: 5V DC Supply
- Reading Distance: 6-10 cm.
- Read frequency: 125 kHz.
- EM4001 64 – bit RFID tag compatible.
- 9600bps ASCII output.
- Current : <50 mA
- Operating Frequency: 125 Khz
- This RFID Reader Module 125Khz is easy to use
- It is Low Cost
- It gives RS-232 and TTL Output
- Need a very less external component to drive
- TTL Level Compatible (Directly connected to the microcontroller)
- Small Buzzer & LED available to know about the card presence
- High-Quality PCB material & Original component only
- Dimension:32* 32* 8mm
Water Level Sensor
TURBIDITY SENSOR
- Working voltage: DC5V
- Measure water turbidity and estimate water quality
- Operating Current: 30mA (MAX)
- Response time : <500ms
- Digital and analogue output
- High level: 5V, low level: 0V
- Operating temperature: -30 to 80 degrees C
- Storage temperature:-10 to 80 degrees C
- Compatible with Arduino, Raspberry Pi, AVR, PIC, etc.
- Weight: 15g
Soil Moisture Sensor
- Operating voltage: 3.3V to 5V Operating Current: 5mA.
- Dual output mode, analogue output and digital output
- Analogue output is more accurate
- Fixed bolt hole for easy installation
- Onboard power indicator (red) and digital switching output indicator (green)
- LM393 comparator chip
- Panel PCB Dimension: Approx.3cm x 1.5cm
- Soil Probe Dimension: Approx. 6cm x 3cm
- Cable Length: Approx.21cm
- Dimensions: 98 x 23 x 4.mm
- Weight (gm): 15
Rain Drop Sensor
- Operating voltage: 5V
- Provide both digital (DO) and analogue (AO)Â output
- Adjustable sensitivity with inbuilt potentiometer
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- Bolt holes for easy installation
- Voltage compactor IC: LM393
- Antioxidant material
- Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance
- Comparator output signal clean waveform is good, driving ability, over 15mA
- Anti-oxidation, anti-conductivity, with long use time
- With bolt holes for easy installation
- PCB or module size: 30mm x 16mm
- Control board size: 54mm x 40mm
- Weight: approx. 8g
MQ7 Module
- Operating voltage: DC 5 V.
- Interface Type: Analog
- The analogue output voltage, the higher the concentration the higher the voltage.
- Detection Gas: carbon monoxide
- Detection range: 10 to 10000ppm
- Â Four screw holes for easy positioning.
- Has a long life and reliable stability.
- Fast response and recovery characteristics.
- Adjustable sensitivity
- Dimension: 32mm x 22m x 27mm
MQ4 Module
- Interface Type: Analog & Digital
- Working voltage: DC 5V
- DOUT: TTL output
- AOUT: Analog output
- Detection Gas: Natural gas/Methane
- Detection range: 300 to 10000ppm
- Digital Out is High or Low based on an adjustable preset threshold,
- Stable & Long Life.
- Onboard Power indication
- Standard Encapsulation Bakelite, Metal cap
- Good sensitivity to Combustible gas in a wide range
- High sensitivity to CH4, Natural gas.
- Small sensitivity to alcohol, smoke.
- Fast response and recovery
- Adjustable sensitivity
- Dimension: 32mm x 22m x 27mm
MQ2 module
- Interface Type: Analog & Digital
- Working voltage: DC 5V
- Working Current: 150mA
- DOUT: TTL output
- AOUT: Analog output
- Preheat time: Over 20s
- Detection Range: 300 -10000 ppm
- Sensitive to H2, LPG, CH4, CO, Alcohol, Smoke or Propane,
- Digital Out is High or Low based on an adjustable preset threshold,
- High Sensitivity to Smoke & combustible gasses like Hydrogen, LPG & Propane.
- Stable & Long Life.
- Onboard Power indication
- The TTL output signal is a low level
- Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
- Fast response and recovery
- Adjustable sensitivity
- Dimension: 32mm x 22m x 27mm
Analog Hall Magnetic Sensor Module
- Operating Voltage: 3.3V-5V
- Wide range voltage comparator LM393
- Number of Pins: 4.
- Sensitivity is Adjustable.
- Output form digital switch output (0 and 1 high and low level)
- The output effective signal is a low level
- Signal output indicator with the retaining bolt hole, convenient installation
- When there is sound, outputs low level and the signal light
- Single-channel signal output
- Can be used for Acoustic control light, give sound and light alarm working with the Photosensitive sensor, and sound control, sound detect