Water flow sensor SEN-HZG1WA Pulse Output 4~45L/min Liquid Switch Flowmeter
- Model: SEN-HZG1WA.
- Use voltage: DC 5V.
- Connect way: G1”, 60*34*34(mm).
- Working voltage range: DC 4.5 ~18V.
- Working current: 15mA.
- Test range: 4~45L/min (m³/h).
- Fit media: water.
- Working pressure: 1.75MPa.
- Outside nominal diameter: G1 (mm).
- Instantaneous flow pulse characteristics: F= [5Q-3]±10%, F means instantaneous pulse value(Hz),Q means instant flow(L/min).
- Insulation resistance = 100MO.
- Electric strength: AC 500V, 50Hz.
- Precision grade: +-10%.
- Working temperature: 60 degree C
- Type: vane-wheel type flowmeter.
MCP2515 CAN Module TJA1050 Receiver SPI 51 Single Chip Program Routine Arduino
- Input Supply voltage: 5V
- Input Supply Current: 5 mA
- Support CAN V2.0B technical standard, communication rate 1Mb / S.
- 0 to 8 bytes long data field.
- 8MHZ crystal oscillator
- 120Ω terminal resistance
- Use High-speed CAN transceiver TJA1050
- SPI control for expanding Multi CAN bus interface
- Using serial port could view the communication data
- With the independent key, LED indicator, Power indicator
- With power pin
- Positioning screw hole centre spacing 23 mm x 38 mm
- The working current: typical 5mA, standby current 1 microamp. Except for the power indicator.
- Standard frames, extended frames, and remote frames.
- Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation
CD74HC4067 High Speed CMOS 16-Channel Analog/Digital Multiplexer Breakout Module
MAX30102 Heart Rate Oxygen Pulse Breakout Sensor Module For Arduino
- Integrated LEDs, Photo Sensor, and High-Performance Analog Front -End
- Optical Heart-Rate Monitor and Pulse Oximetry Solution
- Measures absorbance of pulsing blood
- I2C interface plus INT pin
- Tiny 12.7mm x 12.7mm (0.5in x 0.5in) Board Size
- Highly integrated, small-size sensor
- Non-chest based heart-rate/SpO2 detection
- Ultra-Low-Power Operation Increases Battery Life for Wearable Devices
- Programmable Sample Rate and LED Current for Power Savings
- Ultra-Low Shutdown Current (0.7µA, typ)
- Advanced Functionality Improves Measurement Performance
- High SNR Provides Robust Motion Artifact Resilience
- Integrated Ambient Light Cancellation
- High Sample Rate Capability
- Fast Data Output Capability
MAX7219 Dot Led Matrix Module 4 In 1 Display with 5P Line Module For Arduino Micro-controller
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 320 mA
- Requires only 3 communication wires of MCU
- Pre-cascaded MAX7219 Dot Matrix LED Module.
- The overall size of the display is very compact
- With 64 fixing screw holes, hole diameter: 3mm.
- M3 holes for mounting.
- Module with input and output interfaces
- Support for cascading multiple modules
- Quite large display
- Display Dimensions: 32x32x6 mm
- PCD Dimensions: 128×32mm
- Weight: 55 gm
Double Analog Potentiometer Module With Slide Potentiometer Slip Adjustable Resistance For Arduino
- Dual analogue output, output 0-VCC analogue voltage signal.
- Voltage: 3.3V, 5V.
- Port: Analog.
- Resistance: 10K.
- Slide potentiometers module
- Two analogue outputs, analogue outputs 0-VCC voltage signals
- Stable and reliable performance with high-quality sliding appliances
- Platform: Arduino, MCU, ARM, and other microcontroller platforms
- Application: Raspberry Pi projects, DIY projects, Arduino projects.
- Dimensions: 91 x 21 x 30 mm
- Weight: 18 gm.
Pixy2 CMUcam5 Smart Vision Sensor – Object Tracking Camera for Arduino, Raspberry Pi, BeagleBone Black
- Pixy2 detects lines, intersections and small barcodes, intended for line-following robots.
- Improved framerate – 60 frames-per-second.
- Tracking algorithms have been added to colour-based object detection.
- Improved and simplified libraries for Arduino, Raspberry Pi and other controllers
- Integrated light source.
- The small, fast, easy-to-use, low-cost, readily-available vision system
- Learns to detect objects that you teach it
- Connects to Arduino with the included cable. Also works with Raspberry Pi, BeagleBone and similar controllers.
- Supports C/C++ and Python
- Communicates via one of several interfaces: SPI, I2C, UART, USB or analogue/digital output.
- Configuration utility runs on Windows, macOS, and Linux.
- All software/firmware is open-source GNU-licensed.
- Dimensions: 43mm x 39mm x 16mm
- Height of Camera: 4mm / 0.16""
- Weight (no IDC cable, no screws): 10g.
Finger print Scanner Module – TTL (GT-521F32)
- Operating Voltage: 3.3V to 6V DC
- Simple UART & USB communication protocol.
- Complies with USB 2.0 full-speed specification.
- Ultra-thin optical sensor.
- Finger window: 12.9 x 16.9 mm.
- Image Size: 258 x 202 Pixels.
- Resolution 450 dpi.
- Capable of 360° recognition.
- Storage for 200 unique fingerprints.
- False Acceptance Rate (FAR): <0.001%
- False Rejection Rate (FRR): <0.01%
- Wake up on Finger Function.
- CPU: ARM Cortex M3 Core MCU).
- Ultra-thin Optical Sensor.
- Works well with dry, moist or rough fingerprints
- Anti-scratch with surface high hardness ≧5
- 1:1 verification, 1:N identification.
- High accuracy and high-speed fingerprint identification technology.
- External UART-to-USB converter required (TX & RX levels: 3.3V).
Finger Print Module Scanner – TTL (GT-521F52)
- Simple UART & USB communication protocol.
- Complies with USB 2.0 full-speed specification.
- Ultra-thin optical sensor.
- Resolution 450 dpi.
- Capable of 360° recognition.
- Storage for 3,000 unique fingerprints.
- Wake up on Finger Function.
- Works well with dry, moist or rough fingerprints.
- Anti-scratch with surface high hardness ≧
- 1:1 verification, 1:N identification.
- High accuracy and high-speed fingerprint identification technology.
Mini Ultra-small Size ESP-M3 From ESP8285 Serial Wireless WiFi Transmission Module Fully Compatible With ESP8266
- Model: ESP8285 ESP-M3
- 32-bit Tensilica L106 microcontroller
- Ultra-low 16 bit RISC
- Fully Compatible with ESP8266
- Embedded TCP protocol
- channel high-precision 10-bit ADC
- Supporting the most commonly used networks (802.11 b / g / n)
- Support WPA, PA2PSK and WPS
- Working temperature: -40 ℃ - + 125 ℃
- Clock Speed: 80 MHz; (max 160 MHz)
- Flash memory: 1 MB
- Interface: HSPI, UART, I2C, I2S, Remote Control IR Control, PWM, GPIO
- Direct WiFi Support (P2P)
- Support mode: CCMP, TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc
- Low consumption
- Easy access to the pins
Mini ESP-M2 ESP8285 Serial Wireless WiFi Transmission Module SerialNET MODE Fully Compatible With ESP8266
ESP8285 M2 WiFi IoT Module :
- SOC characteristics.
- Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS.
- Built-in TCP/IP protocol.
- Built-in one-channel 10-bit high precision ADC.
- Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO.
- The deep sleep current is 10uA, the cut-off current is smaller than 5uA.
- Wake, connect and transmit data package within 2ms.
- The consumer power is smaller 1.0Mw (DTIM3) when at standby status.
- Built-in 1M byte for SPI Flash.
- Ultra-small size.
- Support serial to WiFi.
- Wireless transparent transmission.
- Long-distance transmission with ultra-low power.
- Support outboard antenna.
- Bearing high temperature to 125 °C, compared to the 85°C for ESP8266.
- Support 802.11 b/g/n/e/I.
- Support Station, Soft AP, Soft AP+STA mode.
- Support WiFi Direct (P2P).
- Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration.
- P2P finding, P2P GO mode/ GC mode and P2P power management.
- WPA/PA2PSK and WPS.
- 11securitycertification: pre-certification and TSN.
- Support 802.11n (2.4GHz).
- 1h/RFC1042 frame encapsulation.
- Support seamless roaming.
- Support AT remote update and cloud update (OTA).
- Support Smart Config function (including Android and Ios device
TB6612FNG Dual Motor Driver Module 1A for Arduino/Other Microcontroller
- Driver Model: TB6612FNG
- Operating voltage: 2.7 V to 5.5 V
- Limited Maximum Voltage: 15V max
- Output current: 1.2A
- Maximum Current: 3.2A (peak)
- Number of Channels: 1
- Standby control to save power
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1 spaced pins
- Filtering capacitors on both supply lines
- Dimensions: 30 x 20 x 10mm
- Weight: 22 gm