L9110 FAN MOTOR MODULE
- Propeller diameter : 75mm
- Operating voltage: 5V
- Speed & direction of motor is control by L9110 driver
- Control the wind direction with using steering engine
- Can be easily blow out the lighter flame (beyond 20 cm)
- Designed for fire fighting robot and adopt 9110 H as the bridge drive
- Compatible with:
- Original Arduino Mega 256R3
- Original Arduino UNO R30
- Weight: 12 gm.
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
3.3V/5V MB102 Breadboard Power Supply Module
- Input voltage: 6.5V to 12V
- Output voltage: 3.3V to 5V
- Output current: 700Ma
- Apply to MB102 breadboard
- Sorting jumpers used to switch voltage between 3.3V and 5V
- Onboard LED indicator to show the presence of power
- Short circuit protection
- Fits securely on standard 400 and 830 points on the breadboard
- Dimensions: 53*32*23mm
- Weight: 10gm
PCF8591 ADC-DAC
- Operating voltage range: 2.5V-6V
- Low standby current
- I2C bus serial input/output
- PCF8591 by 3 hardware address pins addressing
- PCF8591 I2C bus speed sampling rate decided 4 analogue inputs programmable single-ended or differential input
- Automatic incremental channel selection
- PCF8591 analogue voltage range from VSS to VDD
- Â On-chip track-and-hold circuit
- Â 8-bit successive approximation A / D converter
- Â 1 analogue output DAC gain
- Single power supply
- Module power supply indicator lights
- DA output indicator
- Dimension: 3.6*2.3cm
DHT22 Sensor
HMC5883L COMPASS
- Power supply:3V - 5V
- Communication: Standard IIC communication protocol
- 3-Axis Magnetoresistive Sensors
- PCB thickness: 1.60 mm
- Measuring range: ± 1.3-8 gauss
- 5 milli-gauss resolution
- Compatible with 5V Microcontrollers
- High compass accuracy with an error of just 1 or 2 degrees
- Maximum output sampling frequency: 160 Hz
- 12-Bit ADC Coupled with Low Noise
- AMR Sensors Achieves 2 milli-gauss
- Maximum communication frequency: 400 kHz
- operating temperatures: -30 to +85 °C
- Designed for High Volume, Cost-Sensitive OEM Designs
- Easy to Assemble & Compatible with High-Speed SMT Assembly
- Onboard voltage regulator allows a wide operating voltage range between 3V-5V
- Field Resolution in ±8 Gauss Fields
- Low Voltage Operations (2.16 to 3.6V)
- Low Power Consumption (100 μA)
- Dimensions: 14.35 x 13.16 x 3.40 mm
MPU6050 6AXIS (GYROSCOPE + ACCELEROMETER) SENSOR
- MEMS 3-axis accelerometer and 3-axis gyroscope values combined
- Power Supply: 3-5V
- Communication: I2C protocol
- Built-in 16-bit ADC provides high accuracy
- Sensing range: +/-2G to +/-16G
- Built-in DMP provides high computational power
- Can be used to interface with other IIC devices like a magnetometer
- Configurable IIC Address
- In-built temperature sensor
- Ideal for noisy power environment
- Operating temperature: -40 degrees to 85 degrees Celsius
- Dimension: 28*14mm
Color Sensor
- Voltage supply: 2.7V to 5.5V
- Colour sensor IC: TSC3200
- Interface: digital TTL
- Single-Supply Operation (2.7V to 5.5V)
- High-Resolution Conversion of Light Intensity to Frequency
- Programmable Color and Full-Scale Output Frequency
- Power Down Feature
- Programmable colour and full-scale output frequency.
- Easy to interface with microcontrollers like AVR, ARM, PIC, Arduino etc
- S0~S1: Output frequency scaling selection inputs
- S2~S3: Photodiode type selection inputs
- OUT Pin: Output frequency
- OE Pin: Output frequency enable pin (active low), can be impending when using
- Support LED lamp light supplement control
- Working temperature range: -40℃ to +80℃
XBee Base Board USB Output
- Compatible with all ZigBee modules (Series 1 and Series 2.5, standard and Pro)
- Built-in 3V3 Voltage regulator
- 3V and 5V dual power output
- 3V and 5V IO compatible
- Status LEDs ( RX, TX, RSSI, Power)
- Zig Bee Pins available at 2.54 mm berg strip
- USB Powered.
- Small footprint.
- All XBee pins are broken out.
- Reset button.
- USB 2.0 protocol
- BitBang mode ready
- Easily connected to a PC via mini USB cable
- XBee-setting support software X-CTU
SIM800L GPRS GSM Module
- Chip: SIM800L
- Operating voltage: 3.7V -4.2V
- Current : 2A
- Quad-band (850/900/1800/1900MHz) supports
- Searches for network and login automatically
- Can connect any global GSM network with 2G sim
- Miniature size
- AT command interface with auto baud detection
- Lead-out buzzer and vibration motor control port
- Scan and receive FM radio broadcast, send and receive SMS and call
- Power consumption:
- Interface: UART (max 2.8V, serial interface)
- Command support: 3G PP TS 27. 007, 27. 005 and SIMCOM enhanced AT commands
- Sim Card Slot: Micro SIM
- Temperature range: -40℃ to 85℃
1.44 red serial LCD display module 128*128 TFT Color Screen PCB Adapter
- Display Size: 1.44″
- Driver IC: ST7735
- Input Voltage: 3.3V to 5V
- Resolution:128×128 color pixels
- Touch Screen: NO
- Interface Type: SPI
- TFT color screen, the effect is far better than other small CSTN screen
- Fully compatible and alternative 5110 interface
- On-board LDO, support 5V/3.3V input voltage
- PCB Size: 44×30mm
MMA845 Digital Triaxial Accelerometer Precision Tilt 3-Axis Module
- Power Supply: 3v-5V.
- Pitch: 15mm.
- Mounting hole diameter: 3mm.
- IIC digital output.
- Up to two interruption functions.
- ±2 g/±4 g/±8 g dynamically selectable full scale
- Three motion detection channels.
- Freefall down or motion detection.
- Automatic ODR change for auto-wake and return to sleep
- Pulse detection.
- Vibration detection.
- Dimension: 1.45cm x 2.05 cm (L x W).