I2C MODULE WITH 16*2 CHARACTER LCD
- Supply voltage: 5V
- Display mode: STN
- Display format: 16*2
- Input data: 4 bit or 8 bit (for LCD)
- I2C address: 0x20~0x27 (original address is 0x20,we can change it ourselves)
- Compatible with multiple communication logic levels: 2.8~5VDC
- Compatible for 16*2 LCD
- Serial I2C control of LCD display using PCF8574
- Allow data display via only 2 wires.
- Backlight and contrast adjustment by the potentiometer
- Supports 7 ASCII fonts, 5 graphic functions
- Supports 128 level backlight lightness adjustment.
- Support 64 level screen contrast adjustment
- Supports device address modification
- Dimension: 10*4*5cm
- Size: 150gm
36O DEGREE ROTATIONAL ENCODER
SPEED MEASUREMENT SENSOR
- Using imported groove optical coupling sensor, width 5mm.
- Good signal and waveform
- The strong driving ability for more than 15mA.
- Use the LM393 wide voltage comparer.
- It has the output state light, if the output is high level, the lights are off. If the output is low level, it is on.
- If it is covered, it will output a high level; otherwise, its output low level.
- Equipped with a fixed bolt hole, easy install.
- The DO output interface can be directly connected to a micro-controller IO port if there is a block detection sensor, such as the speed of the motor encoder can detect.
- DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.
DHT11 MODULE
- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0°C to 50°C
- Humidity Range: 20% to 90%
- Resolution: Temperature and Humidity both are 16-bit
- Accuracy: ±1°C and ±1%
- Low power consumption.
- The module can detect the surrounding environment of the humidity and temperature
- High reliability and excellent long-term stability
- The output from the digital output
- Has fixed bolt hole and easy installation
HEART BEAT SENSOR
Analog Hall Magnetic Sensor Module
- Operating Voltage: 3.3V-5V
- Wide range voltage comparator LM393
- Number of Pins: 4.
- Sensitivity is Adjustable.
- Output form digital switch output (0 and 1 high and low level)
- The output effective signal is a low level
- Signal output indicator with the retaining bolt hole, convenient installation
- When there is sound, outputs low level and the signal light
- Single-channel signal output
- Can be used for Acoustic control light, give sound and light alarm working with the Photosensitive sensor, and sound control, sound detect
LDR Module
- Operating Voltage:3V to 5V DC
- Operating Current: 15milli amps
- LED indicating output and power
- LM393 comparator chip
- Can detect ambient brightness and light intensity.
- Output Type :Â - Digital switching outputs (0 and 1) -D0
- Output Digital: 0V to 5V, Adjustable trigger level from preset
- Power indicator (red) and the digital switch output indicator (green)
- It can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- Fixed bolt hole for easy installation
- PCB size: 3cm * 1.6cm
4 Bits Tube Led Display Module Four Serial for Arduino 595 Driver
- Display common anode for the four red LEDs.
- Digital tube 8 Gray Adjustable.
- Level control interface for 5V or 3.3V.
- 4 M2 screws positioning holes for easy installation.
- Ease to use.
- Ease of multiplexing.
- Can use as a 4 digit display unit.
- Can use as a clock display.
- Used for Electrical/Electronic projects.
- Dimension: 42X24X12mm
A1 Universal Carbon Resistors & Rotary Potentiometers Parts Set for Arduino
Socket Adapter Plate Board for 8 Pin Nrf24L01 Wireless Module
- Used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
- On-Board Voltage Regulator:
- Dimension: 15.3 x 11.5 x 1.2 cm
- Weight: 10 Grams
TM1637 4 Bits Digital Tube LED Display Module With Clock Display for Arduino
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 30 mA
- Display Dimensions: 42x24x12 (LxWxH) mm
- Ease to use.
- Ease of multiplexing.
- Can use as a 4 digit display unit.
- Can use as a clock display.
- The counter project uses 7 segment display.
- 4 M2 screws positioning holes for easy installation
