XBee Module S2C XB24CZ7WIT-004
- Protocol: ZigBee®
- Transceiver chipset: Silicon Labs EM357 SoC
- RF Standard: 802.15.4
- Frequency (ISM Band): 2.4GHz
- Digital I/O: 15
- ADC Channels: (4) 10-bit ADC inputs
- Data Rate: RF 250 Kbps, Serial up to 1 Mbps
- Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m)
- Transmit Power: 3.1 mW (+5 dBm)
- Channels: 16 channels
- Encryption: 128-bit AES
- Voltage requirements: 2.1 to 3.6 VDC
- Current requirements: ~33 mA @ 3.3VDC (transmit), ~28 mA @ 3.3VDC (receive), <1 uA @25ºC (sleep)
- Migratable to Digi Mesh and ZigBee PRO protocols
- Configuration Method: API or AT commands, local or over-the-air (OTA)
- Communication: CMOS UART / SPI
- Dimensions: 27.61 x 24.38 x 4.06 mm
- Operating temperature range: -40 to +85 °C
- Integrated, Wire Antenna
- Interoperable with other ZigBee-compliant devices
- Programmable versions with on-board microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Through-hole form factor enables flexible design
RFID EM18 125KHz RS232 Output
- Operating Voltage: 5V DC Supply
- Reading Distance: 6-10 cm.
- Read frequency: 125 kHz.
- EM4001 64 – bit RFID tag compatible.
- 9600bps ASCII output.
- Current : <50 mA
- Operating Frequency: 125 Khz
- This RFID Reader Module 125Khz is easy to use
- It is Low Cost
- It gives RS-232 and TTL Output
- Need a very less external component to drive
- TTL Level Compatible (Directly connected to the microcontroller)
- Small Buzzer & LED available to know about the card presence
- High-Quality PCB material & Original component only
- Dimension:32* 32* 8mm
Water Level Sensor
Soil Moisture Sensor
- Operating voltage: 3.3V to 5V Operating Current: 5mA.
- Dual output mode, analogue output and digital output
- Analogue output is more accurate
- Fixed bolt hole for easy installation
- Onboard power indicator (red) and digital switching output indicator (green)
- LM393 comparator chip
- Panel PCB Dimension: Approx.3cm x 1.5cm
- Soil Probe Dimension: Approx. 6cm x 3cm
- Cable Length: Approx.21cm
- Dimensions: 98 x 23 x 4.mm
- Weight (gm): 15
Rain Drop Sensor
- Operating voltage: 5V
- Provide both digital (DO) and analogue (AO)Â output
- Adjustable sensitivity with inbuilt potentiometer
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- Bolt holes for easy installation
- Voltage compactor IC: LM393
- Antioxidant material
- Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance
- Comparator output signal clean waveform is good, driving ability, over 15mA
- Anti-oxidation, anti-conductivity, with long use time
- With bolt holes for easy installation
- PCB or module size: 30mm x 16mm
- Control board size: 54mm x 40mm
- Weight: approx. 8g
MQ7 Module
- Operating voltage: DC 5 V.
- Interface Type: Analog
- The analogue output voltage, the higher the concentration the higher the voltage.
- Detection Gas: carbon monoxide
- Detection range: 10 to 10000ppm
- Â Four screw holes for easy positioning.
- Has a long life and reliable stability.
- Fast response and recovery characteristics.
- Adjustable sensitivity
- Dimension: 32mm x 22m x 27mm
MQ4 Module
- Interface Type: Analog & Digital
- Working voltage: DC 5V
- DOUT: TTL output
- AOUT: Analog output
- Detection Gas: Natural gas/Methane
- Detection range: 300 to 10000ppm
- Digital Out is High or Low based on an adjustable preset threshold,
- Stable & Long Life.
- Onboard Power indication
- Standard Encapsulation Bakelite, Metal cap
- Good sensitivity to Combustible gas in a wide range
- High sensitivity to CH4, Natural gas.
- Small sensitivity to alcohol, smoke.
- Fast response and recovery
- Adjustable sensitivity
- Dimension: 32mm x 22m x 27mm
MQ2 module
- Interface Type: Analog & Digital
- Working voltage: DC 5V
- Working Current: 150mA
- DOUT: TTL output
- AOUT: Analog output
- Preheat time: Over 20s
- Detection Range: 300 -10000 ppm
- Sensitive to H2, LPG, CH4, CO, Alcohol, Smoke or Propane,
- Digital Out is High or Low based on an adjustable preset threshold,
- High Sensitivity to Smoke & combustible gasses like Hydrogen, LPG & Propane.
- Stable & Long Life.
- Onboard Power indication
- The TTL output signal is a low level
- Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
- Fast response and recovery
- Adjustable sensitivity
- Dimension: 32mm x 22m x 27mm
Analog Hall Magnetic Sensor Module
- Operating Voltage: 3.3V-5V
- Wide range voltage comparator LM393
- Number of Pins: 4.
- Sensitivity is Adjustable.
- Output form digital switch output (0 and 1 high and low level)
- The output effective signal is a low level
- Signal output indicator with the retaining bolt hole, convenient installation
- When there is sound, outputs low level and the signal light
- Single-channel signal output
- Can be used for Acoustic control light, give sound and light alarm working with the Photosensitive sensor, and sound control, sound detect
IR Infrared Obstacle (Imported)
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
