Raspberry Pi 3-MODB+-1GB Motherboard
- 1.2GHz 64-bit quad-core ARMv8 CPU, 1 GB RAM
- 802.11n wireless LAN, 10/100Mbps LAN speed, Upgraded switched Micro USB power source up to 2.5A
- Bluetooth 4.1, Bluetooth low energy
- 4 USB ports, 40 GPIO pins, full HDMI port, combined 3.5mm audio jack, and composite video
- Camera interface (CSI), Display interface (DSI), Micro SD card slot (now push-pull rather than push-push), Video Core IV 3D graphics core
- Warranty Details: 1-year warranty provided by the manufacturer from date of purchase
NVIDIA Jetson Nano 2GB Developer Kit
- The NVIDIA 2GB jetson nano developer kit is the latest addition of the development board to the jetson family.Â
- It has a 2GB memory and 64bit LPDDR4 and runs at a speed of 25.6 GB/s.
- The NVIDIA jetson nano developer kit integrated with a 128-core NVIDIA Maxwell and Quad-core ARM A57.
- Â This development board was created to be the ideal basis for learning, building and educating the different possibities of AI.Â
- The NVIDIA jetson nano kit is perfect for learning and developing AI and robotics.
5V-30V Delay Relay Timer Module Trigger Delay Switch Micro USB Power Adjustable Relay Module
- Time can be adjusted by potentiometers
- With MicroUSB 5.0V power input, it is very convenient to use.
- 5V --30V ultra-wide supply voltage.
- External triggering and on-board buttons are two trigger modes.
- With relay suction indicator.
- The anti-interference ability is strong, and the relay will not misbehave under all kinds of disturbances, so it is suitable for industrial control.
- Module can be controlled: 10A 250VAC (AC), 10A 30VDC (DC) below load.
- With Relay follow current protection.
- • Size: 5.4 * 1.9 * 1.8cm
3S BMS BOARD 25A
- Charging Voltage: 12.6V DC CC/CV
- Balance Voltage for Single Cell: 4.2V
- Max Continuous Charge/Discharge Current: 25A
- Overcharge voltage range: 4.25-4.35v + 0.05v.
- Over discharge voltage range: 2.3-2.7v + 0.05v.
- Operating current: 0 – 25A.
- Operating temperature: -40 – +50℃.
- Instantaneous current: 35 – 40A.
- Storage condition: -40 – +80℃.
- Quiescent current: less than 30uA.
- Balance current: about 40 – 50mA.
- Effective life: more than 30000 hours.
- Internal resistance: less than 100m ohms.
- Short-circuit protection: protection, delayed self-recovery.
STM32F103C8T6 ARM board
Attiny 85
- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 8K Bytes of In-System Programmable Program Memory Flash
- Endurance: 10,000 Write/Erase Cycles
- 512 Bytes In-System Programmable EEPROM
- Endurance: 100,000 Write/Erase Cycles
- 512 Bytes Internal SRAM
- Peripheral Features
- High-Frequency PWM Outputs with Separate Output Compare Registers
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- Single-Ended Channels
- 2 Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Speed Grade: 0 – 10 MHz @ 2.7 – 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
Attiny 5 Version 1
- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 8K Bytes of In-System Programmable Program Memory Flash
- Endurance: 10,000 Write/Erase Cycles
- 512 Bytes In-System Programmable EEPROM
- Endurance: 100,000 Write/Erase Cycles
- 512 Bytes Internal SRAM
- Peripheral Features
- High-Frequency PWM Outputs with Separate Output Compare Registers
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- Single-Ended Channels
- 2 Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Speed Grade: 0 – 10 MHz @ 2.7 – 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
UNO R3 Transparent Case
- Material: A grade acrylic sheet.
- For Arduino UNO R3 Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
- Simply Clicks Together Enclosure.
XNUCLEO-F103RB, Improved STM32 NUCLEO Board
- Core: ARM® 32-bit Cortex™-M3
- Operating frequency: 72MHz
- Operating voltage: 2.0V-3.6V
- Package: LQFP64
- Memories : 128kB Flash, 20kB SRAM
- Interfaces : 2 x SPI, 3 x USART, 2 x I2C, 1 x CAN, 1 x USB
- AD/DA : 2 x AD (12 bit, 16 channels)
- Compatible with NUCLEO-F103RB, onboard Cortex-M3 microcontroller STM32F103RBT6
- Arduino connectivity support, easy to connect with various Arduino shields and access the massive Arduino resources
- ST Morpho headers provide full access to all STM32 I/Os, easy for peripheral expansion
- Supports mbed, build a prototype quickly by mbed SDK and online tools
- Comprehensive free software HAL library including a variety of software examples
- Comes with a separated ST-LINK/V2 module
Mini St-Link V2 Stlink Emulator Downloader Stm8 Stm32 with Metal Shell
- Support the full range of STM32 SWD interface debugging, simple interface (including power supply), 4 line speed, stable work; Interface definition shell directly address
- Support all series STM8 SWIM download debugging (common development environment such as IAR, STVD, etc.) are supported.
- Support the firmware upgrade automatically, to ensure that the ST company product support. When they leave the firmware has been upgraded to the latest V2. The J17. S4.
- Increase the 5 v power output, the output it can protect the I/O port, not afraid of error cause damage of ST-LINK V2.
- Easy interface to use pure copper plating 2.54 spacing horn, with 20 cm Dupont line, can deal with different target board line sequence, flexible connection;
- Use U disk aluminium alloy shell to protect the mainboard, convenient to carry, not afraid of static electricity, not afraid of tumbling.
- Material: metal + plastic
- Colour: Black/Red/Green/Pink/Gold/Grey/Blue/White( Randomly Sent )
- Power output: 5V
- simulator: about 5.6*2*0.8cm
- Debugging line: about 20cm
- Weight (kg): 0.012
