Ultrasonic Module HC-SR-04
- Sensor Type: Ultrasonic
- Output: Digital Sensor
- Voltage: 5VDC
- Operating Current: 15mA
- Measure Angle: 15°
- Ranging Distance: 2cm - 4m
- Static current: < 2mA
- Level output: high-5V
- Output Signal:5V
- High Precision: Up to 2 mm
- Input Trigger Signal: 10µs TTL impulse
- Echo Signal: Output TTL PWL Signal
- High sensitivity ultrasonic range sensor
- Works with Arduino board
Ultrasonic Module Waterproof
- Operating Voltage: 5 V
- Sonar Sensing Range: 25-450 cm
- Sensing Range: 450 cm
- Frequency: 40 kHz
- Resolution: about 0.5cm
- Quiescent current: 5mA
- Total current draw: 30mA
- Beam Angle: less than 50 degrees
- Working temperature: -10 ~ 70 Celsuis
- Storage temperature: -20 ~ 80 Celsuis
- Small size, easy to use
- Low voltage, low power consumption
- High accuracy
- Strong anti-jamming
- Integrated with wire enclosed waterproof probe
- Suitable for wet, harsh measurement
UNO R3 +WiFi ATmega328P+ESP8266 Module CH340G Compatible For Arduino Uno
- Microcontroller: ATmega328IC
- Wi-Fi: ESP8266
- USB-TTL converter: CH340G
- Power Output: 5V-800mA
- Power input USB: 5V (500mA max.)
- Power input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- WiFi: 802.11 b/g/n 2.4 GHz
- USB type: Micro USB
- USB Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O Pins: 14
- Analog I/O pins: 6
- Memory Size: 32Mb
- Interface Type: serial
- Operating temperature: −40С°/+125С°
- Dimensions (L×W)mm: 53.34×68.58
UNO R3 Transparent Case
- Material: A grade acrylic sheet.
- For Arduino UNO R3 Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
- Simply Clicks Together Enclosure.
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.
USB Blaster ALTERA CPLD/FPGA Programmer
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000, and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K, and FLEX10K, etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download modes: AS, PS, and JTAG.
- Support and Nios II embedded soft core processor communication and debugging Rev.C latest version Hardware. Support jtag_uart.
- Speed is 6 times faster than parallel port download cable ByteBlasterII.
- Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
- Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
- Operating Voltage: 1.5～5V JTAG IO Voltage.
- System configuration: Windows XP, Windows Vista, Windows7, USB interface.
USB Control Module 1 Channel 5V Relay Module (No Need Driver)
- Contact type: NC / COM / NO
- Input current: ≥300mA
- Input voltage: DC 5V
- Support Win7, XP 32-bit systems
- Onboard square USB interface, stable connection.
- Use an imported high-performance USB control chip.
- Application code: Green indicates that the relay is closed, the red disconnect
- Military-grade PCB board production
- Using genuine Single relay, the module uses HID technology, without any driver on the windows system plug and play, easy to use and simple
- Military-grade PCB board production
- Board power outlets and terminals, two kinds of access to power is flexible. After connecting the power, even if the computer is off or unplug the USB from the computer, the relay can also remain set.
USB Host Shield
- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Operates over the extended -40°C to +85°C temperature range
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
- Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).
USB PC Intelligent Control Module 2 Channel 5V Relay Module (No Need Driver)
- Contact type: NC / COM / NO
- Input current: ≥300mA
- Input voltage: DC 5V
- Support Win7, XP 32-bit systems
- Onboard square USB interface, stable connection.
- Use an imported high-performance USB control chip.
- Application code: Green indicates that the relay is closed, the red disconnect
- Military-grade PCB board production
USB TO RS-485 CONVERTER
- Small and compact size
- Baud rate:75 bps-115200bps, up to 6Mbps
- Communication distance:1200m
- Support USB 2.0 standard
- Self-powered by USB bus
- Working temperature:-40degree - +85 degree
- RS-232 serial port transmission speed of max 115.2Kbps
- Supports full handshake protocol, full-duplex data operating mode
- Directional control: Uses automatic data flow control technology, automatic identification and control of data transfer direction Load capacity: support multipoint
- Interface protection: TVS tube protection, USB self-recovery protection
- Screw Terminal Connector for easy connection
- The module requires no external power, it takes power from the USB port
- Supported Systems: Windows XP, Vista, Windows 7, Linux, macOS, and
- Dimension:6.1x1.6x1.3cm
USB TO SERIAL CP2102 CONVERTER
- Reliable and stable device
- Baud rate:300bps-1Mbps
- Supports Windows, Linux &Mac
- Compliant withUSB2.0 at a full-speed 12Mbps
- Self-power :3.0 to 3.6v
- USB bus power:4.0 to 5.25v
- Supports all handshaking and modem interface signal
- Standard USB type A male and TTL 6pin connector.
- 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Temperature Range: -40 to +85.
- Dimension: 42mm X 15mm.
USBASP PROGRAMMER
- No special USB controller required
- Programming speed is up to 5Kbytes/sec
- Working platform: Linux, Windows, Mac OS X
- Allows to read or write the microcontroller EEPROM, firmware, fuse bits, and lock bits
- No special controllers or SMD components are needed.
- Target is supported by the SCK option with a low clock speed (<1.5MHz)
- Programming status and Bus status are easily identified
- The easy interface is achieved by Header pins for various ISP header pins
- Dimension: 63.3*20.5*10.5mm
- Weight: 15gm