Pic Kit-2 Programmer
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
Raspberry Pi Zero v1.3
ESP32 SIM 800 WITH WIFI MODULE
- Chipset :ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor
- FLASH: QSPI flash 4MB / PSRAM 8MB
- SRAM:520 kB SRAM
- Button: Reset
- USB to TTL: CP2104
- Modular interface: UART,SPI,SDIO,I2C,PWM,TV PWM,I2S,IRGPIO
- On-board clock:40MHz crystal oscillator
- Working voltage:2.7V-3.6V
- Working current: About 70mA
L9110 FAN MOTOR MODULE
- Propeller diameter : 75mm
- Operating voltage: 5V
- Speed & direction of motor is control by L9110 driver
- Control the wind direction with using steering engine
- Can be easily blow out the lighter flame (beyond 20 cm)
- Designed for fire fighting robot and adopt 9110 H as the bridge drive
- Compatible with:
- Original Arduino Mega 256R3
- Original Arduino UNO R30
- Weight: 12 gm.
ARDUINO MEGA CNC SHIELD
MOTOR SHIELD L293
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SIM 800
- Quad-band 850/900/1800/1900MHz.
- GPRS class 2/10.
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
- High-Quality Product (Not hobby grade).
- 5V interface for direct communication with MCU kit.
- Configurable baud rate.
- Built-in SIM Cardholder.
- Built-in Network Status LED.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Low power.
Microwave Sensor
24V 2CO 6A PCB Relay
- Voltage: 24V
- Current: 6A
- Complete range from PCB to power relays to cover all of your switching requirements
- International certifications and approvals including CE, CSA, EAC, PCT, RINA, VDE and RoHS, providing quality assurance of a market leading product
- Compact construction allowing for most efficient use of space
Raspberry pi 4 case – acrylic clear
- 6-piece Acrylic case with access to all Ports on pi 4
- Compatible for All variants of the Raspberry pi 4 Model B
- Easy to assemble without any Screws or Nut-Bolts
- Slots to route GPIO and CSI ribbon cable
- Cut-out for micro SC card at the bottom panel
- Mounting holes and anti-slip rubber feet at the back.
1.3″ OLED Display I2C 128*64 display module Blue 4pin
PICkit 3.5 Compatible Programmer with USB Cable and Jumper Wire- PIC Kit
- Type: Debugger/Programmer
- Tool/Board Application: Debugging/Programming
- MCU Supported Families: Flash-based PIC MCUs
- Core Architecture: PIC, dsPIC
- IC Product Type: In-Circuit Debugger
- USB (Full speed 12 Mbits/s interface to host PC)
- Real-time execution
- MPLAB IDE compatible
- Built-in over-voltage/short circuit monitor
- Firmware upgradeable from PC/web download
- Supports low voltage to 2.0 volts (2.0v to 6.0v range)
- Diagnostic LEDs (power, busy, error)
- Read/write program and data memory of the microcontroller
- Erase of program memory space with verification
- Freeze-peripherals at breakpoint
- Program up to 512K byte flash with the Programmer-to-Go
- Easy to use Windows-based programming
- USB Interface