IR Proximity Module using TSOP
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
Arduino CNC Shield v3 Engraving Machine/3D Printer/A4988 driver GRBL compatible
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin Molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
Arduino Mega 2560 Board
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 128 KB of which 4 KB used by the boot loader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
LTH 1550-01 IR Transmitter Reciever module
- Type: reflective.
- Fast switching speed
- Pin count :4
- Reverse Voltage: 5 V
- Sensing Distance: 3.81 mm
- Maximum collector-emitter voltage: 30V
- Operating Temperature: -25 ° C to +85 ° C
- Maximum forward current: 1A
- Dimensions: 8.7mm (L) x 4.5mm (W) x 5.6mm (H)
- Maximum emitter-collector voltage: 5V
- Maximum power dissipation for input diode: 90mW
- Maximum collector current: 20mA
- Maximum power dissipation for output phototransistor: 100mW
- Non-contact switching
- For direct PC board or dual-in-line socket mounting
Smart 3pin DHT11 Digital Temperature And Relative Humidity Sensor Module + PCB
- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0°C to 50°C
- Humidity Range: 20% to 90%
- Resolution: 1%RH humidity, temperature 1
- Accuracy: ±1°C and ±1%
- Low power consumption.
- The module can detect the surrounding environment of the humidity and temperature
- High reliability and excellent long-term stability
- The output from the digital output
- Has fixed bolt hole and easy installation
2.4″ Inch Touch Screen TFT Display Shield for Arduino
- 4″ Touch LCD TFT display module for Arduino
- 240*320 pixels resolution
- Ability to display 262000 different colours
- The shield comes equipped with a microSD card slot.
- SPFD5408 controller with built-in video RAM buffer
- 8-bit digital interface, plus 4 control lines
- 5V compatible. Use with 3.3V or 5V logic
- On-board 3.3V 300mA LDO regulator
- Uses digital pins 5-13 and analogue 0-3. That means you can use digital pins 2, 3, and analog 4 and 5. Pin 12 is available if not using the microSD
- Works with any Arduino Uno and mega compatible boards
- Resolution: 240320 pixels
- Supply voltage: 5V
- Working temperature: -30C ~ 70C
- Dimension: 72*52*12mm
L293D Motor Driver Shield
- L293D motor driver chip & 74HC595 shift register
- Four H-bridges
- Terminal blocks and jumper to connect external power, for separate logic/motor supplies
- Up to 4 bi-directional DC motors with individual 8-bit speed selection
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
- PCB Size: 69 x 53 mm
MAX30102 Heart Rate Oxygen Pulse Breakout Sensor Module For Arduino
- Integrated LEDs, Photo Sensor, and High-Performance Analog Front -End
- Optical Heart-Rate Monitor and Pulse Oximetry Solution
- Measures absorbance of pulsing blood
- I2C interface plus INT pin
- Tiny 12.7mm x 12.7mm (0.5in x 0.5in) Board Size
- Highly integrated, small-size sensor
- Non-chest based heart-rate/SpO2 detection
- Ultra-Low-Power Operation Increases Battery Life for Wearable Devices
- Programmable Sample Rate and LED Current for Power Savings
- Ultra-Low Shutdown Current (0.7µA, typ)
- Advanced Functionality Improves Measurement Performance
- High SNR Provides Robust Motion Artifact Resilience
- Integrated Ambient Light Cancellation
- High Sample Rate Capability
- Fast Data Output Capability
MT8870 DTMF Audio/Speech Decoding Telephone Module
- Power Input: 5V Nominal (4.5V - 5.5V)
- 5 Channel Interface
- Detects 0-9, A-D, *, #
- 54” Pin pitch
- On-board 3.5mm jack input Facility
- On-board MT8870 frequency decoder chip
- On-board voice input interface
- On-board LED lights for output state indication
- Low power consumption
- Internal gain setting amplifier
- Adjustable guard time
- 5 Channel interface
- Power-down mode
- Inhibit mode
- Does not require external circuits or wiring,
- Dimension: 37 x 25 x 12 mm
Mega R3 +WiFi ATmega2560+ESP8266 Module CH340G Compatible For Arduino Mega
- Microcontroller:ATmega2560
- IC Wi-Fi : ESP8266
- USB-TTL converter: CH340G
- Power Out: 5V-800mA
- Power Input USB: 5V (500mA max.)
- Power Input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- Wi-Fi 802.11 b/g/n 2.4 GHz
- USB: Micro USB
- Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O: 54
- Analog I/O: 16
- Memory Size: 256kb
- Data RAM Type/Size: 8Kb
- Data ROM Type/Size: 4Kb
- Interface Type: SerialOTA
- Operating temperature:−40С°/+125С°
- Build in external antenna
- Dimensions:53.361×101.86mm
Mini LCD Digital Thermometer Sensor Wired for Room Temperature
- Temperature Range: -50 to +110°C
- Temperature Display Resolution: ±0.1
- Temperature Measurement Accuracy: 1°C
- Cable Length: 1 Meter
- Easy to use, small, and handy module.
- Module powered by a pair of LR44 button batteries.
- Display Size: 34 x 15 mm
- Dimension: 46 x 26 x 15 mm
- LCD Digital Thermometer for Aquarium Freezer H155 New modelling is simple, elegant.
- LCD panels connections online, moisture-resistant, strong anti-interference
FlexiForce Tekscan A301 Sensor
- Thickness 0.203 mm (0.008 in.)
- Length 25.4 mm (1 in.)**
- Width 14 mm (0.55 in.)
- Sensing Area 9.53 mm (0.375 in.) diameter
- Connector 2-pin Male Square Pin
- Substrate Polyester
- Pin Spacing 2.54 mm (0.1 in.)
- Small size is ideal for prototyping and integration
- Available with Enhanced Stability Series (ESS) pressure-sensitive ink for high-temperature and high-humidity environments
- Thin and flexible
- Easy to use