CS DC Geared Motor 30 RPM
Generator Motor Big
CS DC Geared Motor 60 RPM
RS-37 300 RPM High Torque Side Shaft DC Geared Motor
- Nominal Voltage: 12v
- Torque Rated: 39 N-cm
- Shaft Diameter: 6mm (with internal hole)
- Shaft Length:30mm
- Gearbox diameter: 37
- Length:80mm
- Voltage : 9 to 18 No-load current : 500 mA(Max)
- Load current: 3 A(Max)
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
- Weight : 300 gms
Motor Type 3V-4.5V Cell Phone Micro Vibrator
ESC 30A BLDC Electronic Speed Controller
- Standard 30A BLDC ESC Electronic speed controller
- Input voltage: DC 6V-16.8V(2-4S Lixx)
- BEC: 5V 2amp
- Easy handling and good compatibility
- Suitable Batteries: 2-3S LiPo.
- Application: BLDC Motors, Multirotor, RC Planes et
- Running current: 30A (Output: Continuous 30A, Burst 40A up to 10 Secs.)
- Size: 36* 26* 7mm
- Weight: 32g
Offside Gear Motor – Side Shaft 30 rpm 12v DC
- Voltage : 3v to 12v
- RPM :30 (at 12v)
- Nominal Voltage : 12v
- No- Load Current : 20mA
- Full Load Current :800mA
- Full (Stall) Load Torque:20 kgcm
- The lightweight and compact-sized motor with high performance.
- The Shaft is D type hence wheel/ coupling arrangement is simple.
- Useful for hobbyists and for a DIY project.
- Weight: 150gm
DYS Motor D2826 1100KV
- Item name: D2826 1100KV
- Voltage: 4V~14.8V
- Battery: 2~4s LiPoly
- Max watt: 102
- Max Current: 19A
- Suggested prop: 9045
- Pull: 660g
- Shaft: 3.17mm in Diameter
- Thrust: 1050g (9045 prop/4s)
- Efficiency: <4g/W
- Suggested Propeller: 8x6(2s) 7x4(3s)
- ESC: 30A
- Shaft: M5
- Pull: 660g
- Motor Mount Holes: M3 x 16/19mm
- Dimensions: 26.2 × 27.7mm
- Weight: 51g
STEPPER MOTOR MINI
A2212 BRUSHLESS DC MOTOR 1800kv BLDC
- KV: 1800
- No load Current : 10 V : 0.5 A.
- Current Capacity: 12A/60s
- No Load Current @ 10V: 0.5A
- Of Cells: 2-3 Li-Poly
- Motor Dimensions: 27.5 x 30mm
- Shaft Diameter: 934;3.17mm
- Shaft diameter : 3.175mm.
- Minimum ESC Specification: 18A (30A Suggested)
- Thrust @ 3S with 1045 propeller: 1000gms approx
- Thrust @ 3S with 0945 propeller: 650gms approx
- Thrust @ 3S with 0845 propeller: 550gms approx
300 RPM 12V DC CENTRE SHAFT GEAR MOTOR
Square Geared Motor 300 rpm- High Torque
- Power Supply: 12V DC
- RPM: 300
- Rated Torque: 7 kg-cm
- 8mm Dia shaft with M4 thread hole
- Gearbox diameter: 70 mm
- Motor Diameter: 42 mm
- Length without shaft: 106 mm
- Shaft length: 27mm
- Heavy Duty Metal Gears.
- Uniformity of parts.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- Relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
- Weight: 630gm
100 RPM L-Shape BO Motor
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage: 3~12 V DC
- Shaft Length: 8.5mm
- Shaft Diameter: 5.5mm (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 100 RPM
- Rated Torque: 1 Kgcm
- Cost-effectiveness of the injection-molding process.
- Elimination of machining operations.
- Low density: lightweight, low inertia.
- Uniformity of parts.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
- The quietness of operation.
- Tolerances often less critical than for metal gears, due in part to their greater resilience.
- Consistency with the trend to greater use of plastic housings and other components.
Offside Geared Motor 12V 5 RPM – High Torque
- Voltage : 3v to 12v
- RPM :5.5 (at 12v)
- Nominal Voltage: 12v
- No- Load Current : 20mA
- Full Load Current:800mA
- Full (Stall) Load Torque: 30kgcm
- Shaft diameter: 6 mm
- Motor mounting screw: 4 x M3 and depth 3.5mm
- Motor body Length: 75mm
- Motor Body Diameter: 37mm
- The lightweight and compact-sized motor with high performance.
- The Shaft is D type hence wheel/ coupling arrangement is simple.
- Useful for hobbyists and for a DIY project.
- Weight: 150gm
12V DC Geared Motor 2000 RPM
1000 RPM – 12V CS DC Geared Motor
BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
- Input voltage: 6V-27V
- Maximum current: 43A
- Input level: 3.3-5V
- Control mode: PWM or level
- Duty cycle: 0-100%
- Double BTS7960 large current (43 A) H bridge driver
- 5V isolate with MCU and effectively protect MCU
- 5V power indicator on board
- Four lines from MCU to driver module (GND. 5V. PWM1. PWM2)
- Reverse the motor forward, two PWM input frequency up to 25kHZ
- Two heat flow passing through an error signal output
- Dimension: Approx. 4 * 5 * 1.2cm
Toy Motor Long Shaft
- Â DC 12V
- 13000 rpm motor
- long shaft high speed motor
- Suitable for toy car and other toys.
- Good heat dissipation with cooling fan
- Voltage: 12V.
- No Load Current: 0.9A
- No Load Rotate Speed: 13000r/ min. Shaft Length: 20mm/ 0.79in
- Shaft Diameter: 3mm/ 0.12in. Size: 92mm x 37mm x 37mm/ 3.62in x 1.46in x 1.46in. Net Weight: 230g/ 8.11oz. Color: Silver
Bo Motor Double Shaft 150RPM
- RPM: 150
- Operating Voltage : 3V - 9V
- Gear materials: plastic.
- Motor types: permanent-magnet.
- Brush-type: Brush.
- Uncommitted motors: Homopolar motors.
- Magnet types: ferrite magnets.
- Torque: Approximate 2.5Kg/cm.
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- Relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
- Quietness of operation.
- Tolerances often less critical than for metal gears, due in part to their greater resilience.
- Consistency with trend to greater use of plastic housings and other components.
SERVO MOTOR SG9G
Worm Gear Box Reduction Motor 12V 110rpm 30 kg-cm Torque – WGM555127500-68K
- Operating Voltage: 12.V DC
- Rated Current: 1.1 A
- Rated Base Motor RPM: 7500.
- Rated Speed: 110RPM
- Rated Torque: 30kg-cm
- Operating Temperature: (°C) - -40 °C ~ +100°C.
- Relative Humidity(RH): 20% ~ 85% .
- Housing Material: Metal.
- Shaft Type: D-type.
- Motor Height: 27mm
- Motor Width: 40mm.
- Motor Length:Â 115mm
- Shaft Diameter: 8mm
- Shaft Length: 15mm
- Shaft Type: D-type. Motor
Worm Gear Box Reduction Motor 12V 175rpm 30 kg-cm Torque – WGM5551212000-68K
Worm Gear Box Reduction Motor 12V 88rpm 30 kg-cm Torque – WGM555126000-68K
CS DC Geared Motor 500 RPM
Square Geared Motor 60 RPM – High Torque
- Operating Voltage: 12 V DC
- No Load Current: ≤220 mA
- No load Speed: 60 RPM (at 12V)
- Full Load Current: ≤1300mA
- Rated Current: ≤4800 mA
- Rated Torque: 40 Kg-cm
- Shaft Length: 27 mm
- Shaft Diameter: 8 mm
- Length: 92mm
- Dimension Overall: 70 X 70 (Sq.) X 90 (Length)
- Heavy Duty Metal Gears.
- Uniformity of parts.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- Relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
RS-50-555 Gear Motor – High Torque 12v DC 300 rpm
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 2 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 10Kg-cm
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
RS-50 High Torque Side Shaft DC Gear Motor 200 RPM
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 4 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 90Kg-9kg
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
Johnson Geared DC Motor Grade-B 1000 RPM 12V
- Base Motor RPM: 18000
- Operating Voltage: 6-18 V
- Rated Voltage: 12 V
- Rated Torque: 0.8 kg-cm
- Stall Torque: 3.5 kg-cm
- Gearbox Dimensions: 25×37 (LxW) mm
- The motor has sturdy construction.
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
12V DC Johnson Motor Grade A-100 RPM
- 100RPM 12V DC motors with Metal Gearbox and Metal Gears
- 18000 RPM base motor
- Holding Torque: 27.18kgcm
- 6mm Dia shaft with M3 thread hole
- Gearbox diameter 37 mm.
- Motor Diameter 28.5 mm
- Length 63 mm without shaft
- Shaft length 30mm
- 180gm weight
- No-load current = 800 mA, Load current = upto 7.5 A(Max)
- The motor has sturdy construction.
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
DYS Motor D2826 1400KV
- Item name: D2826 1400KV
- Voltage: 4V~14.8V
- Battery: 2~4s LiPoly
- Max watt:205W
- Max Current: 19A
- Suggested prop: 9045
- Pull: 660g
- Shaft: 3.17mm in Diameter
- Thrust: 1050g (9045 prop/4s)
- Efficiency: <4g/W
- Suggested Propeller: 7x4(3S)Â ~Â 9x4.7 (2S)
- ESC: 40A
- Ri(M ): 0.078
- Pull: 780g
- Shaft: M5
- Motor Mount Holes: 16mm or 19mm
- Dimensions: 26.2 × 27.7mm
- Weight: 51g