AfroFlight Naze32 Rev6 Flight Controller Board
- Version: 6 DOF
- Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line
- USB on right side
- 32-bit processor running at 3.3V/72MHz (STM32F103CB).
- Up to 8 Ch. RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spectrum satellite receivers
- Built-in FrSky telemetry inverter
- Battery voltage monitoring
- SBUS Inverter built-in
- Spectrum satellite
- Modern GUI for all operating systems, Baseflight Configurator.
- Supports multiple platforms: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
- MPU6500 : 3-Axis MEMS Gyroscope + accelerometer
- Onboard MicroUSB for setup and configuration
- BMP280 barometer
- Modern GUI for all operating systems, Baseflight Configurator.
- Sonar pads w/resistors added for direct connection to 5V sonar3.3V
- Dimensions: 36x36 mm (30.5mm Mounting)
- Weight: 5.3 grams (no headers, 7.3 grams with).
F450 Quadcopter Frame
- Model: F450
- Frame width: 450mm
- Frame height: 55mm
- Frame Weight: 282g
- Take-off Weight: 800g ~ 1200g
- Motor Mount Bolt Holes: 16/19mm
- Landing Gear Height: 150mm
- Landing Gear Weight: 90gm
- Made by advanced engineering material, super strong & smooth.
- High quality and strong ability of anti-fall, lower maintenance cost.
- Compact design with small numbers of components, you can assemble it by yourself quickly and easily.
- Recommended Propeller: 10x4.5in;8x4.5in
- Recommended Battery: 3S~4S LiPo
- Recommended Motor: 22x12mm (Stator size)
- Recommended ESC: 20A/30A ESC
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
QAV250 Quad-copter Frame
- Item name: QAV250 Frame Kit
- Arm plate thickness: 3mm
- Main material: 3k carbon fibre
- Wheelbase: 250mm
- The arm equips dampers for a safe landing.
- The arm has multiple motor mounting holes.
- Equips vibration-free mounting bracket for FPV camera.
- Recommend Propeller: 5 inch
- Recommend Motor: 1806 2204 2206
- Recommend ESC: 8A-12A
- Recommend Battery: 1300Mah-2200Mah
FlySky 2.4Ghz 6CH Receiver
- Item Name: FS-R6B Receiver
- Brand Name: Flysky
- Power input: 4.0 -6.5 V DC
- RF power: less than 20DBm
- Modulation: GFSK
- Code type: PCM
- Sensitivity: 1024
- PWM channels: 6
- Protocol: AFHDS
- Distance: >150m
- Antenna type: Built-in antenna
- Low voltage warning: LED
- Charger port
- Certificate: CE,FCC,RoHS
- Dimension: 30*25*8mm
- Weight: 25g
4-wheel Robot Smart Car Chassis Kits Car Model with Speed Encoder
- Operating Voltage: 3-6V VDC
- Gear Ratio: 1:48
- No-load speed(5V): about 200 RPM
- Rated Torque: 0.8 Kg.cm @ 5V
- Load current: 170mA (when it is 4.5V)
- Shaft Length: 10 mm
- Shaft Type: 6 mm, Double-D
- Loading Capacity: Max 2.5Kg
- Wheel Diameter: 65 mm
- Wheel Width: 27 mm
- Body Material: Plastic
- Grip Material: Rubber
- Very handy and simple in assembling/disassembling.
- Strong components so as to withstand extreme terrain conditions.
- Transparent Car Chassis.
- Attractive design.
- Double-layer structure, much of mounting holes, enough space
- Easy to install a variety of control panels, sensors
- Simple mechanical structure, easy for installation.
- Adopts 4 DC motors for better power, speed and load capacity
- Easy interface with Arduino development platform
- Enormous space between middle & bottom chasis
Q330 Quadcopter Frame
- Colour: Black & Red
- Wheelbase: 325mm
- Frame Diameter: 330mm
- Frame Spacing: 30mm
- Recommend to use 3S 2200-4000mah Lipo battery
- Glass fibre material on centre plates
- Glass-filled nylon arms for increased strength and durability
- Lightweight arm design
- Integrated PDB for easy wiring and tidy installation
- Increased internal space for additional electronics/equipment
- Additional mounting holes for frame upgrades
- Suitable for CC3D\MWC\APM\PIXHAWK\NAZA flight control
- Recommend to use 2204/2205 + 6045propeller + 12A ESC, violate flying recommend to use 2208 motor + 20A ESC + 8045 propeller
- Dimension: 21.5*10.5*5cm
- Weight: 231g
Metal mechanical Arm Gripper claw
- Metal Gripper Robotic Arm
- Operating Voltage: 4.8V to 6.6V
- Material: Aluminum Alloy
- The Kit comes with hardware, unassembly
- Clamp Max open: 55mm
- Clamp total length:108mm
- Clamp total width:98mm (when the Clamp open
- Light weight plank kit
- Compatible with HS322, HS422, MG995, SG5010 servo
- Degree of Freedom (DOF): 2
- Bearing Type: Ball Bearing
- Weight: About 68g
Mini OSD W/ KV Team MOD For Racing F3 Naze32 Flight Controller RC Drone
- NO DC/DC converter, hence less heating
- FTDI cable compatible pinout
- Standard 6-pin ISP header
- Two LED indicators
- ATmega328P with Arduino bootloader
- MAX7456 monochrome on-screen display
- Pad for an Analog or Digital PWM RSSI signal
- Pad for the connection of a Current Sensor
- ATmega328P with Arduino bootloader
- Standalone, or with APM / Flip / Flip32+ flight controllers
- These modifications allow direct connection of two batteries (up to 4S)
- This hardware takes the hardware mods for this firmware and builds them into an RTF solution.
- This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
- Two independent power sections with an LED indicator on each.
- Solder jumpers for combining the power sections
- Solder jumper for PAL video option
- +5V 500mA regulator for up to +12V supply input
- Exposed test points for HSYNC and LOS ATmega328P with Arduino bootloader.
- Dimension: 16 x 16mm
6 in 1 DIY Solar kit for Kids, Solar Powered Vehicles, Science Educational Toys for Kids STEAM Kits
- Product name: STEM Solar Power Science Educational Toy Set
- Product size (After assembly):
- Robot: 5 x 5 x 8 cm
- Helicopter: 25.5 x 8.5x8cm
- Submarine: 14 x 8 x10.5 cm
- Mildwill: 8.5x8.5x9cm
- Aircraft: 25.5x8.5 x17cm
- Car: 6.5 x 5 x5.5cm
- Package Dimensions: 19*6*24CM
- Suit for : 10,11,12,13,14 years old Boys, Girls, Kids, Children, toddler, nephew, niece, granddaughter, grandson, friends, Birthday, Christmas, party or other holiday gifts
EMAX BLHELI 12Amp ESC for Quadcopter / Drones
- Based on BL Heli firmware.
- ESC Type: Brushless.
- Built in linear or switched BEC.
- Constant Current: 12A
- Burst Current: 15A
- BEC Mode: Linear BEC : 5v / 1A
- Lipo Cells: 2-4
- Constant Current: 12A.
- Support: One-shot 125 Protocol.
- Includes low voltage protection, over heat protection, and self-check functions.
- Separate power supply for MCU and BEC, helping eliminate magnetic interference.
- Fully programmable by any standard programming card or directly from your transmitter.
- Customisable throttle range.
- Weight: 11g
- Dimension: 42x20x8mm
MR.RC 12A ESC
- Input Voltage: 2-3S LIPO
- Working Current: 12A
- Burst current (10S): 15A
- BEC: 5V / 1A Programmable: Yes
- With stable performance, it is practical and durable
- Offer you high compatibility, reliability, and stability
- Throttle range can be set to be compatible with different receivers.
- Equipped with built-in linear BEC or switch BEC.
- Easy to install and convenient to use
- Play a significant role in driving and controlling the motor to complete all kinds of instructions
- Suitable for 250 Mini four-axis and F330 aircraft, etc
- Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.
- Dimensions:38 x 20 x 6 mm
- Weight: 30g