I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-30%
A3144 Hall Effect Sensor
Original price was: ₹110.00.₹60.00Current price is: ₹60.00. inc. GST
BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
Original price was: ₹1,500.00.₹950.00Current price is: ₹950.00. inc. GST
PICKIT2 Microcontroller USB Programmer PIC KIT2 Burner
Original price was: ₹2,500.00.₹1,750.00Current price is: ₹1,750.00. inc. GST
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
Description
The PICkit 2 Development Programmer/Debugger was designed as a low-cost development tool with an easy-to-use interface for programming and debugging Microchip’s Flash families of microcontrollers. This programmer is capable of programming all current 8-, 16-, and 32-bit Flash PIC microcontrollers. And also includes the UART Tool and Logic Tool microcontroller development utilities.
Microchip’s PICKit2 is designed as much more comfortable, reliable, and powerful than the other programmers all over the internet. It is a USB-based ICSP (In-Circuit Serial Programming) programmer. As PICKit2 is a USB-powered device, it gets power from a PC USB +5V power supply. Meanwhile, the soul of the PICKit2 is the USB microcontroller PIC18F2550. The USB Data+ and Data- from the PC connected to the D+ and D- pins of the PIC182550. Moreover, using a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller. It is made up of high-quality PCB FR4 Grade with FPT Certified. This programmer module supports the following device families:
- PIC10F
- PIC12F
- PIC16F
- PIC18F
- PIC24
Reviews (0)
Shipping & Delivery
Related products
CH341A 24 25 Series EEPROM Flash BIOS USB Programmer with Software & Driver
- USB interface
- With CH341A chip
- Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip
- With 24/25 status indicator lamp
- Support USB to TTL conversion
- Support 24EEPROM and 25 SPI flash 8pin/ 16pin chip
- Recognize 25 series chip automatically
- Supports download STC series procedure of single chip
- SPI pin to support expanding the utility
- STC microcontroller supports a full range of program download
- Support expanding the utility by SPI pin
- With SOP8 SOP16 to DIP8 converter board
- Used in wide applications – PC motherboard, LCD monitor, DVD, router program reading and writing
- Supports Windows XP, Vista, Win7 and Win8 (32/64bit) system
- Provide 5V-3.3V power supply output
Pic Kit-2 Programmer
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
PIC18F4520 Microcontroller IC
- Maximum CPU Frequency: 40 MHz
- Architecture: 8 bit
- Program Memory (Flash): 32 kB
- RAM: 1536 byte
- Internal Oscillator: 8MHz, 32 KHz
- ADC: 1 (13 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- C Compiler Optimized Architecture: - Optional extended instruction set designed to optimize re-entrant code
- 100,000 Erase/Write Cycle Enhanced Flash Program Memory Typical
- 1,000,000 Erase/Write Cycle Data EEPROM Memory Typical
- Flash/Data EEPROM Retention: 100 Years Typical
- Self-Programmable under Software Control
- Priority Levels for Interrupts
- 8 x 8 Single-Cycle Hardware Multiplier
- Extended Watchdog Timer (WDT): - Programmable period from 4 ms to 131s
- Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via Two Pins
- In-Circuit Debug (ICD) via Two Pins
- Wide Operating Voltage Range: 2.0V to 5.5V
- Programmable Brown-out Reset (BOR) with Software Enable Option
PL2303 USB TO TTL CONVERTER
- USB specification 2.0 compliant with full-speed 12Mbps.
- Operation Level-Digital 5V
- Power Supply-External 5V
- Standard USB type A male and TTL 6pin connector.
- 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
- Simple serial communication.
- Router or ADSL firmware upgrade.
- Easy to use, RX to the MCU's TX; TX to the MCU's RX. and then connected to the GND. Without having to use the MAX232 conversion.
RS232 TO RS485 CONVERTER ADAPTER
- Input: USB 2.0 Protocol
- Output: RS232 on DB9 Male connector compatible to PC RS485/RS422 on the terminal block.
- Communication Speed: 300bps to 230Kbps.
- Auto direction control for RS485- 2W data transmission.
- Plug-and-Play (Device is Hot-pluggable)
- Cable: USB 2.0 type A to type B cable.
- Galvanic Isolation of 1.5kV
- RS232/RS485 line protection: +/- 15kV ESD.
- LED Indication for Transmit Receive signals.
- Input power from the USB port
- No external power is required.
- RS232 with DB9 Female connector
- RS485 with DB9 Male connector
- Baud rate up to 230Kbps.
- Input power supply range 9-6V DC to 26.4V DC
- USB Drivers provided for Win XP, Vista, Win7, Win8
- Working Modes: Asynchronous, half-duplex, differential transmission
- Operating temperature: -10°C to 85°C,
- Relative humidity: 5% to 95%
- Transmission distance: 1.2 mile (RS-485), 5 meters(RS-232)
- Transmission Media: Common wire, double wire, UTP or Shielding Line
- Serial Port Feature: Compatible with EIA/TIA RS-232C standard and RS-485 standard
- Weight: 49gm
Reviews
There are no reviews yet.