I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-17%
SI4432 WIRELESS MODULE
Original price was: ₹550.00.₹500.00Current price is: ₹500.00. inc. GST
USB TO RS-485 CONVERTER
Original price was: ₹550.00.₹400.00Current price is: ₹400.00. inc. GST
PL2303 USB TO TTL CONVERTER
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
- USB specification 2.0 compliant with full-speed 12Mbps.
- Operation Level-Digital 5V
- Power Supply-External 5V
- Standard USB type A male and TTL 6pin connector.
- 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
- Simple serial communication.
- Router or ADSL firmware upgrade.
- Easy to use, RX to the MCU’s TX; TX to the MCU’s RX. and then connected to the GND. Without having to use the MAX232 conversion.
Description
This PL2303 USB to TTL converter module is an integrated USB to TTL UART Converter module. This module consists of the PL2303 Bridge IC designed on basis of Prolific Technology. The PL2303 UART module is a simple solution to update the design of the RS-232 using minimal components and PCB space. PL2303 USB to TTL converter allows asynchronous serial data bus compliant with USB2.0 full-speed function controller, USB transceiver, oscillator, EEPROM, with full modem control. As a result, this module doesn’t need any external components.
PL2303 is used as a standard serial port with Laptops that don’t have a standard serial port. It creates a virtual COM port using the USB on the PC. And this supports a standard baud rate of 300 bps to 1.5 Mbps for serial communication. The LED present in the data lines of the module indicates real-time data transfer status. This module consists of a 500 mA self-recovery fuse used for any protection purpose. PL2303 board is entirely coated by the high-quality transparent heat-shrinkable sleeve. This makes the PCB to insulation state from outside so that the board is not affected by any material shortcut burn.
PL2303 is used with a standard 0.1″ pitch terminal strip to connect directly to UART or I/O pins for easy access to your MCU. This module is compatible with 32-bit & 64-bit Windows, Mac OS 8 to OS X, Linux, and Android. These modules are reserved to operate in 3.3V and 5V pin interface, which makes it easier for the DDWRT of different voltage system that needs power.
Application of PL2303 Module
- Debug purpose in the development
- Microcontroller to PC communication
- Programming related purposes
Reviews (0)
Shipping & Delivery
Related products
A-to-Mini B USB-2.0 Cable for Arduino Nano
- USB Type: Type-A to Mini-B
- Weight: 100 gm.
- Length: 1.35 m.
- Nickel-Plated Connector
- Exclusively designed for Arduino boards.
- Exclusively designed for Arduino boards.
- Mini-USB cables are designed to connect from the USB port on a hub, PC or Mac to a USB device, including digital cameras, mobile phones, and PDAs.
Arduino Uno/Mega Usb Cable (USB A To B)
- USB Type: Type-A to Type-B
- Length: 1 meter
- Gold Plated Connector
- Fully compatible with the PC.
- Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions
- Fully compatible with the PC.
- Moulded strain relief and PVC over molding to ensure a lifetime of error-free data transmissions.
- Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference.
- Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference
- Weight: 80 gm.
PICkit 3.5 Compatible Programmer with USB Cable and Jumper Wire- PIC Kit
- Type: Debugger/Programmer
- Tool/Board Application: Debugging/Programming
- MCU Supported Families: Flash-based PIC MCUs
- Core Architecture: PIC, dsPIC
- IC Product Type: In-Circuit Debugger
- USB (Full speed 12 Mbits/s interface to host PC)
- Real-time execution
- MPLAB IDE compatible
- Built-in over-voltage/short circuit monitor
- Firmware upgradeable from PC/web download
- Supports low voltage to 2.0 volts (2.0v to 6.0v range)
- Diagnostic LEDs (power, busy, error)
- Read/write program and data memory of the microcontroller
- Erase of program memory space with verification
- Freeze-peripherals at breakpoint
- Program up to 512K byte flash with the Programmer-to-Go
- Easy to use Windows-based programming
- USB Interface
PICKIT-3 Programmer
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.
RS232 TO RS485 CONVERTER ADAPTER
- Input: USB 2.0 Protocol
- Output: RS232 on DB9 Male connector compatible to PC RS485/RS422 on the terminal block.
- Communication Speed: 300bps to 230Kbps.
- Auto direction control for RS485- 2W data transmission.
- Plug-and-Play (Device is Hot-pluggable)
- Cable: USB 2.0 type A to type B cable.
- Galvanic Isolation of 1.5kV
- RS232/RS485 line protection: +/- 15kV ESD.
- LED Indication for Transmit Receive signals.
- Input power from the USB port
- No external power is required.
- RS232 with DB9 Female connector
- RS485 with DB9 Male connector
- Baud rate up to 230Kbps.
- Input power supply range 9-6V DC to 26.4V DC
- USB Drivers provided for Win XP, Vista, Win7, Win8
- Working Modes: Asynchronous, half-duplex, differential transmission
- Operating temperature: -10°C to 85°C,
- Relative humidity: 5% to 95%
- Transmission distance: 1.2 mile (RS-485), 5 meters(RS-232)
- Transmission Media: Common wire, double wire, UTP or Shielding Line
- Serial Port Feature: Compatible with EIA/TIA RS-232C standard and RS-485 standard
- Weight: 49gm
STC Automatic Programmer USB – TTL 5V 3.3V SCM Burning Programmer
- Supports 3.3V and 5V STC full range of all SCM burning procedures.
- Highest baud rate 115200
- Programmer automatically downloads without cold start, no need to frequently power down SCM.
- 4The burner with USB to TTL, USB to serial port function, can be used for USB to TTL electronic product upgrades, does not affect the normal serial communication debugging
- The success rate of STC12, STC15, STC11, STC10 series programs can be up to100%.
- Programmer uses CH340 + SCM control core.
- With 500MA self-recovery fuse, perfect to protect your computer motherboard!
- Metal aluminium shell protection burner motherboard.
- The interface definition is printed on the shell.
- When burning STC SCM, after clicking download, the light will go out, it will flash when there is data transmission, if no data transmission, it will always keep bright.
- Support win7 8 10 system (64-bit and 32-bit system)
USB TO RS-485 CONVERTER
- Small and compact size
- Baud rate:75 bps-115200bps, up to 6Mbps
- Communication distance:1200m
- Support USB 2.0 standard
- Self-powered by USB bus
- Working temperature:-40degree - +85 degree
- RS-232 serial port transmission speed of max 115.2Kbps
- Supports full handshake protocol, full-duplex data operating mode
- Directional control: Uses automatic data flow control technology, automatic identification and control of data transfer direction Load capacity: support multipoint
- Interface protection: TVS tube protection, USB self-recovery protection
- Screw Terminal Connector for easy connection
- The module requires no external power, it takes power from the USB port
- Supported Systems: Windows XP, Vista, Windows 7, Linux, macOS, and
- Dimension:6.1x1.6x1.3cm
Reviews
There are no reviews yet.