Xbee Pro S2C Module XBP24CZ7WIT-004
- Operating voltage: 2.7V-3.6V
- Max data rate: 250kbps
- 63mW output (+17dBm)
- Range: 1 mile (1600m)
- ADC Channels: 6 10-bit ADC input pins
- Digital I/O: 8
- 128-bit encryption
- Transmit Current: 120mA at 3.3VDC
- Receive current: 31mA at 3.3VDC
- Data Rate: RF 250Kbps, serial up to 1Mbps
- Indoor/urban range up to 300ft (90m)
- outdoor/RF line of sight range up to 2miles (3200m)
- Transmit power is 63mW (+18dBm)
- Receiver sensitivity is -101dBm
- Local or over-air configuration
- AT or API command set
- External Antenna Required
- Firmware upgrades via UART, SPI or over the air (OTA)
- ISM 2.4GHz frequency band, DSSS (direct sequence spread spectrum) interference immunity
- Dimension: 2.438cm x 3.294cm
xcluma Xilinx Xc2C32A Cpld Development Learning Board
XF40 750W 48V MXUS Electric Bike Bicycle Rear wheel Hub motor DIY Conversion Kit
XH-W1219 12V Digital Display Temperature Controller Module W/NTC Waterproof Temperature Sensor
XH-W1401 12V Digital Led Thermostat Module Temperature Controller With Display
- Model: XH-W1401
- Power Supply: DC12V
- Thermostat Range: -9℃ to 99℃
- Thermostat Accuracy: 1℃
- Output : Electric relay output ,capacity 220V 10A/12V 10A
- For cooling or heating temperature control
- Simple Temperature Sensor Module with 12V Relay
- Imported High-Speed single-chip microcomputer.
- Three Display output status indicator.
- Automatically judge heating and cooling according to set temperature.
- Used in various temperature control, water temperature control, incubators, etc.
- Refresh Rate: 0.5 Sec
- Dimension:” 78*55mm
- Weight: 0.040 kg
XH-W3001 DC 12V 120W Digital Microcomputer Thermostat Switch
- Rated Current: 10 Amp Max.
- Measurement Input: NTC10K
- Temp Probe Cable Length: 1 Meter
- Power Supply: DC12V
- Load Power: 120W
- Easy to install
- Output type: Direct output
- Output capacity: max 10A
- Temperature setting upper and lower limits
- Temperature measuring range: -50~110°C
- Temperature control range: -50~110°C
- Control precision: up to 0.1°C
- Up key: Press once to display the start temperature. Long press to set start temperature.
- Down key: Press once to display the stop temperature. Long press to set stop temperature.
- Temperature setting upper and lower limits
- Simple operation, suitable for seafood machines.
- Dimensions 60 x 45 x 31 (mm)
- Weight: 55gm
XH-W3001 DC 24V 240W Digital Temperature Controller Microcomputer Thermostat Switch
- Rated Current: 10 Amp Max.
- Measurement Input: NTC10K
- Temp Probe Cable Length: 1 Meter
- Power Supply: DC12V,DC 24V
- Load Power: 120/240/1500W
- Easy to install
- Output type: Direct output
- Output capacity: max 10A
- Temperature setting upper and lower limits
- Temperature measuring range: -50~110°C
- Temperature control range: -50~110°C
- Control precision: upto 0.1°C
- Up key: Press once to display the start temperature. Long press to set start temperature.
- Down key: Press once to display the stop temperature. Long press to set stop temperature.
- Temperature setting upper and lower limits
- Dimensions 60 x 45 x 31 (mm)
- Weight: 55gm
XL4015 5A STEP DOWN WITH DISPLAY
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 degree to + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- LED to indicate power status
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
XL4015 5A STEP DOWN MODULE
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 ~ + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- Power indicator: No
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
XL4015 5A STEP DOWN WITH HEAT SINK
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 degree + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- Power indicator
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
XL4432 LORA Sensor Module
- Frequency range: 433.92M
- High sensitivity up to-121dBm
- Maximum output power: 20dBm
- Data transfer rate: 0.123-256 kbps
- FSK, GFSK, and OOK modulation mode
- 1.8-3.6V power supply
- Ultra-Thin Power Off Mode
- Digital signal strength indicator received (RSSI)
- Synchronization alarm function
- Automatic antenna connection and bidirectional switch control
- The configurable data package structure
- Before sync signal detection
- 64 bytes RX data record (FIFO)
- Low power tests
- Temperature detection and 8-bit analog to digital converter
- Operating temperature range: -20 ~ + 60 C
XL6009 4A DC to DC BOOST CONVERTER
- Module Properties: Non-isolated boost (BOOST)
- Rectification: Non-Synchronous Rectification
- Input Voltage Range: 3V ~ 32V
- Output Voltage Range: 5V ~ 35V
- Input Current: 4A (max), no-load 18mA
- Conversion efficiency: <94%
- Switching frequency: 400KHz
- Output Ripple: 50mV (the higher the voltage, the greater the current, the greater the ripple)
- Load Regulation: ± 0.5%
- Voltage Regulation: ± 0.5%
- Operating Temperature: -40degree ~ +85 degree
- Dimensions: 43mm * 21mm * 14mm
Xmate Zorro Wired USB Gaming Mouse for PC/Laptop/Mac – (Black)
- PC GAMING MOUSE COMPATIBILITY: Windows 10/8/7/Vista/XP/Win98SE/Win2000, Limited Mac OS support Works well with all major Computers/Laptop brands Asus, Dell, Hp, Lenovo, Dell, MSI and others
- Mechanical Button: 6 Buttons with different functions like the previous page and next page. If you wish you can turn on/off the colorful lights (press next page key + DPI key)
- 4 DPI Levels: Four color RGB breathing light cycle replacement. 4-type DPI rating controlled by touching the DPI button - Violet 800/Blue 1200/Purple 1600/Red 3200
- Excellent Performance with High Polling Rate: Xmate Zorro wired gaming mouse with 500Hz high polling rate ensures smooth movement offers reliable connectivity with smooth and responsive tracking
- Ergonomic Gamer Mouse: Made of ABS plastic, leather collar, anti-skid scroll wheel, rubber finish with mechanical switches & 1.5m nylon tough cable that stand up to tough gaming needs like FPS/PUBG/COD, etc
- 1-year warranty from the date of purchase, contact us at 040-67138844 (9am - 6pm, Monday to Friday & Saturday 9am - 1pm)
- Country of Origin: China
XNUCLEO-F103RB, Improved STM32 NUCLEO Board
- Core: ARM® 32-bit Cortex™-M3
- Operating frequency: 72MHz
- Operating voltage: 2.0V-3.6V
- Package: LQFP64
- Memories : 128kB Flash, 20kB SRAM
- Interfaces : 2 x SPI, 3 x USART, 2 x I2C, 1 x CAN, 1 x USB
- AD/DA : 2 x AD (12 bit, 16 channels)
- Compatible with NUCLEO-F103RB, onboard Cortex-M3 microcontroller STM32F103RBT6
- Arduino connectivity support, easy to connect with various Arduino shields and access the massive Arduino resources
- ST Morpho headers provide full access to all STM32 I/Os, easy for peripheral expansion
- Supports mbed, build a prototype quickly by mbed SDK and online tools
- Comprehensive free software HAL library including a variety of software examples
- Comes with a separated ST-LINK/V2 module
XR2206 High Precision Function Signal Generator
- Voltage Supply: 9-12V DC Input.
- Waveforms: Square, Sine & Triangle.
- Impedance: 600 Ohm + 10%.
- Frequency: 1Hz-1MHz.
- SINE WAVE.
- SQUARE WAVE.
- TRIANGLE WAVE.
- High resolution, can generate sine/triangle/square waveforms.
- Adjustable frequency and amplitude.
- Frequency adjustment features coarse tuning and fine-tuning.
- All are through-hole components, easy for installation.
- Dimension: Approx. 12 * 8 * 2cm
- Weight: 69g
XT60 Connector
- Manufacturer: AMASS
- Connector Series: XT60H
- Rated Voltage: DC 500V
- Metal Material: Brass Gold Plated
- Rated Current: 30A
- Momentary Current: 60A
- Number of pins: 2
- Colour: Yellow
- Contact Resistance: 0.55mΩ
- FR Level: UL94 V0
- Use Times: 1000 TIMES
- Temperature: -20℃ to 120℃
- Spatial Orientation Straight
- Compatible for Wire size up to 12AWG
- Mechanical mounting for cable
- Electrical mounting soldered
- Contact plating Gold flash
XT90 Male-Female connector pair with Housing
Yahboom programmable Running:bit based on Micro:bit compatible with LEGO
- Can be created a variety of shapes (Pretty car, Proficient Carrier, Robot with clip, skilled remover, Mobile shooter, etc.)
- Using micro: bit as the core controller, simple and funny graphical or Python programming.
- Multi-function Super:bit expansion board to combine the building blocks and circuits.
- Support Android / iOS dual- system mobile APP remote control, Handle remote control.
- Each shape with rich functions: Bullet throwing, Dance battle, Weightlifting competition, sports competition and so on.
- Detailed assembly steps and more than 30 reference courses.
Yahboom programmable Spider:bit based on Micro:bit V2 compatible with LEGO
Yahboom programmable Spin:bit based on Micro:bit V2 compatible with LEGO
- With the micro:bit as the core controller, Graphical and Python programming.
- Equipped with a multi-function Super: bit expansion board.
- Combine the building blocks and the circuit.
- Support Android / iOS mobile phone APP control.
- A large number of blocks can create a variety of shapes (Ferris wheel, Gyroscope, Fan).
Yellow ABS 1.75 mm 1 KG Filament-Wanhao
- Material: ABS
- Color: Yellow
- Material Diameter: 1.75mm
- Printing Temperature: 220° to 230°C
- Roundness Accuracy: +/- 0.5mm +/- 0.5mm
- Density: 1.31g/cm3 1.01g/cm3
- Mounted: Spool Mounted
- Net weight: 1kg
- Packaging Vacuum-sealed with desiccant to protect the filament from humidity
- Highly Detailed & Quality Outputs.
- Tried and Tested by Makenica.com
- Compatible with any FDM 3D Printer.
- ABS is stronger than PLA
- Easy to post-process.
- Environment friendly – ISO 9001 and ROHS certified
Yellow HIPS 1.75 mm 1 KG Filament-Wanhao
Yellow PLA 1.75 mm 1 KG Filament-Wanhao
- High-quality starting material
- Diameter tolerances of ± 0.1mm checked with laser monitor
- Smooth surface with even rounding
- Lower melting temperature
- Good flow properties
- Little odor development
- Less risk of clogging the nozzle, compared to ABS
- Compatible with almost all 1.75mm FDM printers
- No heating bed necessary
- High quality means less waste
- Easy to use
- No heating bed necessary Printing Settings:
- Best Printing Temperature:200-220℃
- Bed Temperature:0-70℃
- Printing Speed:30~90mm/s
- Movement Speed :90~150mm/s