Ethernet Shield
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
- Can be accessed using the Mini SD TF library.
- The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
- 1500V isolation (input to output)
LoRa SX1278 433M 10KM Wireless Spread Spectrum Transmission Module Ra-02 SX1278 Socket IOT
- Lora Spread Spectrum Modulation Technology +20dBm-100mW
- Constant RF power output when voltage changes
- High sensitivity: low to -148dBm
- Half-duplex SPI communication Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
- 127dB RSSI dynamic range
- Automatic RF signal detection
- CAD model and ultra-high-speed AFC With CRC, up to 256 bytes of the packet engine
- Small volume dual-row stamp-hole patch package
- With shielding shell Spring antenna (Ra-01) external antenna (Ra-02)
- Wireless standard 433MHz Frequency range: 420 ~ 450MHz
- Interface: SPI GPIO
- Operating Voltage:1.8 ~ 3.7V, the typical value is 3.3V
- Current: Receiver:≦ 10.8mA (LnaBoost off, band 1) Transimit: ≦ 120mA (+ 20dBm)
- Sleep mode: 0.2μA
- Working temperature: -40 to + 85 ° C
- Storage temperature: Normal
TEA5767 FM Stereo Radio Module
- Directly plug antenna interface.
- I2C bus communication.
- Multi-capacitor combined filter.
- Blue LED power indicator.
- High sensitivity(low noise RF input amplifier).
- High power auto gains control AGC circuit.
- With reverse polarity protection diode.
- With a power output filtering sensor.
- Blue LED power indicator.
- Onboard 3.5mm audio interface.
- If connects with a single chip, only connect the Power Ground and two I2C communication cables.
- LC harmonic oscillator uses a low-cost fixed chip.
- No need to adjust the Intermediate frequency.
- High sensitivity(low noise RF input amplifier).
- High power auto gains control AGC circuit.
- Soft Mute.3.5mm jack for external Antenna.
DHT21 AM2301 Digital Temperature Humidity Sensor module SHT11 SHT15 Arduino
- Power: DC 3.3-5.2V
- Humidity: 0~99.9% RH
- Temperature: -20 ~ 60℃
- Precision: ±3% RH, ±0.5 ℃
- Output: Digital (1 wire)
- Accurate, durable and high quality
- 4 pin package
- Ultra-low power
- No additional components
- Excellent long-term stability
- All calibration, digital output
- Completely interchangeable
- Long distance signal transmission
- Relative humidity and temperature measurement
- Dimension: 60 x 27 x 14mm
HB100 Microwave Doppler Radar Wireless Motion Sensor Module
Raspberry PI 5MP V1.3 Camera Module
- 5MP Super HD Resolution
- Still Picture Resolution: 2592 x 1944
- Video: Supports 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 Recording
- 2TB HDD for 24/7 Continuous Recording
- Plug and Play; Easy to Use
- Power over Ethernet
- Easy Remote Access and Control
- Fully Compatible with Both the Model A, Model B and Model B+ Raspberry Pi
- 5MP Omnivision 5647 Camera Module
- 4X optical zoom allows you to see the far-away objects clearly without getting closer and compromising in image qualities.
- Dual-band WiFi signal promises you a strong network all the time.
- Waterproof and vandal-proof cover makes it solid even in harsh weather and attack.
- 15-pin MIPI Camera Serial Interface - Plugs Directly into the Raspberry Pi Board
- Size: 20 x 25 x 9mm
- Weight 3g
MAX7219 Dot Led Matrix Module 4 In 1 Display with 5P Line Module For Arduino Micro-controller
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 320 mA
- Requires only 3 communication wires of MCU
- Pre-cascaded MAX7219 Dot Matrix LED Module.
- The overall size of the display is very compact
- With 64 fixing screw holes, hole diameter: 3mm.
- M3 holes for mounting.
- Module with input and output interfaces
- Support for cascading multiple modules
- Quite large display
- Display Dimensions: 32x32x6 mm
- PCD Dimensions: 128×32mm
- Weight: 55 gm
HLK-RM04 UART to Serial Wifi Ethernet Wifi Module
- 2.4GHz 802.11b/g/compatible
- Support IEEE 802.3、IEEE 802.3u
- Wi-Fi Client/AP/Router Mode
- Support WPS/wds
- Baud rate range: 1200~500000bps
- Support transparent transmission mode
- Support multiple security authentication mechanisms: WEP64/WEP128/ TKIP/ AES & WEP/WPA-PSK/WPA2-PSK
- Support multiple network protocol: PPPOE/TCP/UDP/DDDNS & /DHCP/DNS/HTTP/Firewre
- Support AT+ instruction set
- Support two configuration methods: Serial/WEB
- Serial speed ratio adjustable up to 320400
- Transparent dual-way data transmission
- Integrated 10/100M Ethernet port, Max. baud ratio up to 230.4kbps
- Adopts Ralink program, high-quality material
- Built-in 360M MIPS CUP, 16M RAM, 4M FLASH, wireless baseband, RF front-end, and multi-peripheral bus
- Support IEEE 802.11 b/g/n, transparent protocol data transmission mode
- TCP server/TCP Client/UDP work mode, support network protocol: TCP / UDP / ARP / ICMP / HTTP / DNS / DHCP
- Support DHCP auto gain IP, support IP distribution at AP Mode
- Built-in antenna or external antenna
- Dimensions: 29mm*40mm* 8.8mm
GP2Y0A41SK0F 4-30cm
- Model: GP2Y0A41SK0F
- Operating Voltage Range: 4.5~5.5V
- Average current consumption: 30 mA
- Distance measuring range: 4 cm to 30 cm
- Output type: Analog voltage
- Output voltage differential over distance range: 2.05 V (typical)
- Update period: 38 ± 10 ms
- Screw Holes: 37mm apart, 3 mm in diameter
- Connecting cable length:15cm
- Very Small in size
- Less influence on the colour of reflected objects, reflectivity
- Analogue voltage corresponding to the voltage
- External control circuit unnecessary
- Low cost
- The sampling rate of nearly 25 readings per second
- Dimension: 29.5×13×21.6 mm
- Weight: 3.5 gm
AM2302 WIRED MODULE
- Low cost
- 3V to 5V power and I/O
- 5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
- 3 wires 23cm long (9")
- Dimensions: 27x 58.75 x 13.30mm
