JQ6500 Voice Sound Module 16Mbit Music MP3 Play MCU Serial Control Module UART SPI Flash
- Input voltage: Power supply is at 3.2V-5V, 4.2V Power supply is the best
- Rated current: 20ma
- Standard DIP16 package.
- 30 level adjustable volume, 10 adjustable EQ
- Working temperature: -40~70°C
- Humidity: 5%~95%
- Support sampling rate (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
- 24-bit DAC output,
- dynamic range support 90dB, SNR support 85dB
- Full support FAT16, FAT32 file system, the largest support 32G TF card, support 32G U disk, 64M bytes NOR FLASH
- A variety of control mode, parallel port control mode, serial port mode, AD button control mode
- The audio data sorted by folder, up to 100 folders, every folder can be assigned 1000 songs
- You can plug in SPI flash, connect the computer can display spi flash letter to update the content;
- Controlled through the microcontroller serial port to play the specified music;
- Can be interrupted: that is, in the process of playing, press the button will interrupt the current state to perform the new;
- MP3 file format: supports all bit rates 11172-3 and ISO13813-3 layer3 audio decoding
KA2284 Audio level Indicator
- Chip: KA2284.
- Wide operating supply voltage: 3.5V-16V
- `Level amplitude can be adjusted.
- AC/DC signal can be controlled through the jump line.
- High gain rectifying amplifier included(Gv=26dB)
- Low radiation noise when LED turns on
- Logarithmic indicator for 5-dot LED of bar type.
- Constant current output( 15mA)
- Minimum number of external parts required
- PCB board size: 29 x 21 mm
KY-036 Metal Touch Sensor Module
- Main chip: LM393
- Working voltage: for DC 5V
- Single-channel signal output
- Low-level output signal used for human body touch sensor alarm
- Adjustable sensitivity
- Pin Connector to board: 4 Pins
- Dimensions: 43 x 16 x 15 mm / 1.69 x 0.63 x 0.59 inch
- Single-channel signal output
- Low-level output signal used for human body touch sensor alarm
- Adjustable sensitivity
- Long life
- High reliability
L293D Motor Driver Shield
- L293D motor driver chip & 74HC595 shift register
- Four H-bridges
- Terminal blocks and jumper to connect external power, for separate logic/motor supplies
- Up to 4 bi-directional DC motors with individual 8-bit speed selection
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
- PCB Size: 69 x 53 mm
L298P Motor Shield motor driver
- L298P based Arduino motor driver shield
- Operating Voltage 5V to 12V
- Motor controller L298P, Drives 2 DC motors or 1 stepper motor
- The logical part of the input voltage VD: 5V
- Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input
- The logical part of the work current Iss:<36mA
- Driven part of the operating current Io:<2A
- Current sensing 1.65V/A
- Free running stop and brake function
- Maximum power dissipation: 25W (T = 75 Celsius)
- Max current 2A per channel or 4A max (with external power supply)
- Control signal input level: High 2.3V
- Onboard Bluetooth interface, you can directly plug, no wiring required.
- The board with L298P motor drive chip, directly with the motherboard digital I/O port (D10, D11, D12, D13), without cumbersome wiring.
- Onboard buzzer (D4), you can set the reverse alarm ringtones.
- D2, D3, D5, D6, D7, D9 are not occupied by the digital interface.
- A 0 – A 5 six analogue interfaces.
- Forward and Backward steering are indicators
L9110 FAN MOTOR MODULE
- Propeller diameter : 75mm
- Operating voltage: 5V
- Speed & direction of motor is control by L9110 driver
- Control the wind direction with using steering engine
- Can be easily blow out the lighter flame (beyond 20 cm)
- Designed for fire fighting robot and adopt 9110 H as the bridge drive
- Compatible with:
- Original Arduino Mega 256R3
- Original Arduino UNO R30
- Weight: 12 gm.
LDR Module
- Operating Voltage:3V to 5V DC
- Operating Current: 15milli amps
- LED indicating output and power
- LM393 comparator chip
- Can detect ambient brightness and light intensity.
- Output Type : - Digital switching outputs (0 and 1) -D0
- Output Digital: 0V to 5V, Adjustable trigger level from preset
- Power indicator (red) and the digital switch output indicator (green)
- It can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- Fixed bolt hole for easy installation
- PCB size: 3cm * 1.6cm
LDR SENSOR 20mm
LDR SENSOR 5mm
MOQ: 2 nos
- No. of Pins: 2
- Type of Mounting: PCB Through Hole
- Maximum Operating Temperature: +800C (Approx.)
- Dark resistance:1-20M ohm
- Good reliability
- High sensitivity
- Fast response
- Good spectrum characteristic
- Size: 5mm (50-paise size)
- .Coated with epoxy
- Miniature open frame package.
- Proxy coated.
- Moisture resistant.
- Spectral response is similar to the human eye.
Leap Motion Controller
- Power supply: 5V DC via USB connector (minimum 0.5A)
- Data connection: USB 2.0
- Interaction zone: Depth of up to 60cm (24”) preferred, up to 80cm (31”) maximum;
- 140×120° typical field of view.
- 3 LEDs spaced on either side and between the cameras, baffled to prevent overlaps.
- Construction: Aluminium and scratch-resistant glass
- Operating temperature: 32º to 113º F (0º to 45ºC)
- Storage temperature: 14º to 122º F (-10º to 50º C)
- Relative Humidity: 5% to 85% (non-condensing)
- Two 640x240-pixel near-infrared cameras; spaced 40 millimetres apart infrared-transparent window, operate in the 850 nanometre +/-25 spectral range; typically operates at 120Hz; capable of image capture within 1/2000th of a second.
- Highly accurate hand and finger tracking with near-zero latency
- 135° field of view extending above the device
- Orion SDK compatible with Windows 7 or newer
- Updated V4 tracking
LilyTiny (LilyPad ATTiny85)
- Program Memory Type: Flash
- Program Memory (KB) : 8
- CPU Speed (MIPS): 20
- Data EEPROM (bytes): 512
- Digital Communication Peripherals: 1-SPI, 1-I2C
- Capture/Compare/PWM Peripherals : 5
- Comparators: 1
- Temperature Range (C) : -40 to 85
- Operating Voltage Range (V): 1.8 to 5.5
- Pin count: 8
- Cap Touch Channels : 3
