GY-906 MLX90614ESF Contactless Temperature Sensor Module
- Small size, low cost
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Easy to integrate
- Factory calibrated in wide temperature range:
- Sensor temperature: -40...+125°C
- Object temperature: -70...+380°C
- High accuracy of 0.5°C over the wide temperature range
- (0...+50°C for both Ta and To) High (medical) accuracy calibration
- The measurement resolution of 0.02°C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuousreading
- Simple adaptation for 8...16V applications
- Sleep mode for reduced power consumption
GY-906-BCC MLX90614ESF-BCC IR TEMPERATURE MODULE
- Input supply: 3V-5V
- Input current: 2mA
- Small size, low cost.
- Mounted on a breakout board with two types of pins.
- 10k pull up resistors for the I2C interface with optional solder jumpers.
- Easy to integrate
- Factory calibrated in a wide temperature range
- Mounted on a breakout board with two types of pins
- -40 degrees to 125 degrees C for sensor temperature
- -70 degrees to 380 degrees C for object temperature.
- High accuracy of 0.5C over a wide temperature range
- The measurement resolution of 0.02C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuous reading
- Simple adaptation for 8v to 16V applications
- Sleep mode for reduced power consumption
- Different package options for applications and measurements versatility
HB100 Microwave Doppler Radar Wireless Motion Sensor Module
HC-05 Bluetooth Bee Master BEE05
- Power supply: 3.3V
- A power supply of more than 3.3V will destroy the module.
- Paring user’s name: HC-05
- Default baud rate: 38400
- Default slave model
- Default pairing password: 1234
- This module was designed for XBEE so it’s compatible with the XBEE expansion base. This module was designed for XBEE so it’s compatible with the XBEE expansion base.
- It can be used for an MCU system whose voltage is 3.3V.
- Users can set master-slave model, baud rate, paring password, and user’s information by AT command.
- Bluetooth adapter pairs with Bluetooth Bee salve device.
- With an efficient onboard antenna, the exposed antenna qualifies the transmit signal and makes it farther.
- Dimension: : 3.3 x 2.5 x 0.9 cm
- Weight: 5g
HC-05 Bluetooth Module
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Operating Voltage: 4V to 6V (Typically +5V)
- Operating Current: 30mA
- Modulation: GFSK(Gaussian Frequency Shift Keying)
- Emission power: ≤4dBm, Class 2
- Sensitivity: ≤-84dBm at 0.1% BER
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
- Working temperature: -20 ~ +75Centigrade
- Serial Bluetooth module for Arduino and other microcontrollers
- Range: <100m
- Works with Serial communication (USART) and TTL compatible
- Follows IEEE 802.15.1 standardized protocol
- Uses Frequency-Hopping Spread Spectrum (FHSS)
- Can operate in Master, Slave or Master/Slave mode
- Can be easily interfaced with Laptop or Mobile phones with Bluetooth
- Supported baud rate: 9600,19200,38400,57600,115200,230400,460800.
- Dimension: 26.9mm x 13mm x 2.2 mm
HC-05 Bluetooth Shield for Arduino
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Communication Range: 10M
- Serial Bluetooth module for Arduino
- Can operate in Master, Slave or Master/Slave mode
- UART interface (TTL) with programmable baud rate (SPP firmware installed)
- Default baud rate: 38400(CMD MODE) / 9600(DATA MODE), data bits: 8, stop bit: 1, Parity: No parity
- Onboard PCB antenna
- FCC ID certificated
HC-06 4Pin Bluetooth Module Without Reset Switch
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Dormancy current: no dormancy.
- Used for a GPS navigation system, water, and electricity gas meter reading system.
- With the computer and Bluetooth adapter, PDA, seamless connection equipment.
- Bluetooth module HC-08 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
HC-06 Bluetooth Module
- Input Supply voltage: 3.6 - 6V
- Input current: 50 (mA)
- Maximum Operating Range: 10m
- Operating Frequency: 2.4GHz ISM band
- Modulation: GFSK (Gaussian Frequency Shift Keying)
- Emission power: 4dBm, Class 2
- Sensitivity: -84dBm at 0.1% BER
- Operating Temperature: -20 ~ +75 degree C
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps (Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
HC-06 RF Wireless Bluetooth Bee V2.0 Module Xbee V03 Shield Board Arduino
- Power supply: 3.3V
- A power supply of more than 3.3V will destroy the module.
- Paring user’s name: HC-05
- Default baud rate: 9600
- Default slave model
- Default pairing password: 1234
- It can be used for an MCU system whose voltage is 3.3V.
- Users can set baud rate, paring password, and user’s information by AT command.
- Bluetooth adapter pairs with Bluetooth Bee salve device.
- With an efficient onboard antenna, the exposed antenna qualifies the transmit signal and make it farther.
- Be used with for Arduino Bluetooth Bee module, it can communicate with other Bluetooth device wireless
- Be used with Xbee module to achieve communication between more than two for Arduinos or communication between for Arduino and PC
- Dimension: : 3.3 x 2.5 x 0.9 cm
- Weight: 5g
HC-12 433 SI4463 Wireless Serial Module
- IEEE 802.15.4g compliant
- Supply voltage: 3.2V~5.5V
- Operating frequency range: 433.4-473.0MHz,
- Up to 100 channels of communication
- Receive sensitivity = –126 dBm
- Serial TTL (RX, TX, GND) interface
- Modulation (G)FSK, 4(G)FSK, (G)MSK, OOK
- Maximum transmit power: 100mW (settable)
- Max output power: +20 dBm
- Low active power consumption: 10/13 mA RX, 18 mA TX at +10 dBm
- Ultra-low current power-down modes: 30 nA shutdown, 50 nA standby
- Data rate: 100 kbps to 1 Mbps
- Fast wake and hop times
- The highly configurable packet handler
- TX and RX 64 byte FIFOs
- Auto frequency control (AFC)
- Automatic gain control (AGC)
- Low BOM and battery detector
- Default factory settings: Mode FU3, the baud rate is 9600bps, communication channels CH001 (433.4M)
HC-SR505 Mini Infrared PIR Motion Sensor Infrared Detector Module
- Model: HC-SR505
- Operating Voltage Range: DC4.5-20V
- Average Current Consumption (mA): 0.06
- Distance Measuring Range: 3 meters
- Delay time: Default 8S + -30% (can be customized)
- Working Temperature Range: -20°C ~ 80°C
- Sensor Lens Diameter: 10mm
- Induction angle: <100-degree cone angle
- Low-power consumption
- Output level: High 3.3V / Low 0V
- Trigger: repeatable trigger (default)
- Automatic induction: to enter the sensing range of the output is high, people leave the sensor range automatically delay off high, output low
- Dimensions: 10 x 23 x 5mm
- Weight: 10gm
