MEPUNO COMMUNICATION BOARD
- Microcontroller ATMEGA328 P
- Crystal for microcontroller: 16 MHZ
- USB type B connector
- On-Board Power LED Indicator
- 5volt, 12 volt regulated circuit
- Two separate regulated 5volt power supply
- On Board On/Off switch
- On Board DC jack for powering up using adaptors
- On Board Reset Switch
- On Board TX/RX indication LEDs
- On board FTDI Driver for adruino
- Berg headers for external interfacing
- Supports I2C /GSM /GPS/RF/USART serial communication
- Separate berg headers available for PIR, Servo motor, RTC/I2C, GPS_TTL, and USART-TTL
- Four 3pin PBT Connectors
- Four SPDT 12V Relays
- Onboard DB9 connectors for GPS, GSM and USART communication
- Berg slot for 16x4 LCD connections
- Onboard TRIM-POT for LCD
- Onboard RTC IC: IN1307 with crystal 32768 MHZ crystal and CR2302 battery
MEPUNO ROBOT CONTROLLER BOARD
- Microcontroller ATMEGA328 P.
- Crystal for the microcontroller: 16 MHZ
- USB type B connector
- 5volt, 12 volts regulated circuit.
- Two separate regulated 5volt power supplies.
- On-Board On/Off switch.
- OnBoard DC jack for powering up using adaptors.
- On-Board Reset Switch.
- Onboard L293D dual DC motor driver.
- Onboard TSOP IR receiver.
- On Board 3 user LEDs (with jumper selection), TX/RX indication LEDs.
- On-board connectors for analogue interfacing.
- On Board Buzzer Interface.
- Â On-Board PWM Interfacing.
- On board FTDI Driver for adruino.
- Â Berg headers for external interfacing.
- Supports I2C /3 WIRE /RF/USART serial communication standards.
ATtiny85 Arduino-enabled Mini USB Dev Board
- Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
- Power via USB or External Source
- Onboard 5V Regulator
- Built-in USB
- 6 I/O Pins
- 8k Flash Memory (about 6k after bootloader)
- I2C and SPI (vis USI)
- PWM on 3 pins (more possible with Software PWM)
- 10-bit ADC
- ADC on 4 pins
- Power LED and Test/Status LED
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
LilyTiny (LilyPad ATTiny85)
- Program Memory Type: Flash
- Program Memory (KB) : 8
- CPU Speed (MIPS): 20
- Data EEPROM (bytes): 512
- Digital Communication Peripherals: 1-SPI, 1-I2C
- Capture/Compare/PWM Peripherals : 5
- Comparators: 1
- Temperature Range (C) : -40 to 85
- Operating Voltage Range (V): 1.8 to 5.5
- Pin count: 8
- Cap Touch Channels : 3
Arduino Compatible Nokia 5110 Prototype Proto Shield Expansion Board
- Supports Nokia5110 display
- Standard 0.1"x0.1" prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- Â IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- Reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- Surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability
EYE BLINKING SENSOR
- Working Voltage +5V DC
- TTL output 5V or 0VSimple setup.
- Remote detection - no mechanical contact with the eye.
- Stray visible and IR light not affected.
- Our system does not require the restraint of the external eyelids.
- Head movement not affected.
- Excellent frequency characteristics (DC to more than 500 Hz).
- Excellent working distance (15-25 mm).
- Difficult to calibrate using common units of eye blink measurement. (e.g. mm of eyelid displacement)
HC-06 Bluetooth Module
- Input Supply voltage: 3.6 - 6V
- Input current: 50 (mA)
- Maximum Operating Range: 10m
- Operating Frequency: 2.4GHz ISM band
- Modulation: GFSK (Gaussian Frequency Shift Keying)
- Emission power: 4dBm, Class 2
- Sensitivity: -84dBm at 0.1% BER
- Operating Temperature: -20 ~ +75 degree C
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps (Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
Air Pressure Sensor MPX 10
- Pressure Type: Differential Sensitivity
- Operating Pressure Min: 0kPa
- Operating Pressure Max: 0-10kPa
- Minimum Supply Voltage: 3V
- Maximum Supply Voltage: 6V
- of Pins: 4Pins
- Operating Temperature Min: -40°C
- Operating Temperature Max: 125°C
- Low Cost
- Patented Silicon Shear Stress-Strain Gauge Design
- Ratiometric to Supply Voltage
- Easy to Use Chip Carrier Package Options
- Differential and Gauge Options
- Durable Epoxy Unibody Element or Thermoplastic
- (PPS) Surface Mount Package
Tilt Sensor / Vibration Sensor
3 Axis Accelerometer ADXL 335
IR Receiver Black 3mm
- Spectral range (nm):700-1050
- Light Current IL ≥3mA
- Dark current ID< 0.1uA
- Breakdown Voltage> 30
- Maximum forward current 25mA
- Power dissipation Pd(mw): 100
- Package: Through-hole
- Diameter: 3mm
- Maximum reverse voltage 5V
- Maximum Forward Voltage 2 V-1.3V
- Operating Temperature(Celsius) -40°C- +100°C
- Fast Response
- High photosensitivity
- High reliability
Sonar Range Finder -High Performance Ultrasonic Sensor Module
- Low-cost ultrasonic rangefinder
- Size less than 1 cubic inch with easy mounting
- Resolution of 1mm
- 100mS measurement cycle
- The free run operation uses a 2Hz filter, with 100mS measurement and output cycle
- Operating temperature range from -15°C to +65°C
- Operating voltage from 2.5V to 5.5V
- Nominal current draw of 2.5mA at 3.3V, and 3.1mA at 5V